InFocus Projector IN136UST User Manual

							IN134UST/IN136UST User’s Manual 
Network 
 
ITEM DESCRIPTION 
Network State Displays the network connection status. 
DHCP  Press 
◄► to turn DHCP On or Off.  
Note:  If you select DHCP Off, complete the IP  Address, Subnet Mask, Gateway, and 
DNS fields. 
IP Address   Enter a valid IP address if DHCP is turned off. 
Subnet Mask  Enter a valid Subnet Mask if DHCP is turned off. 
Gateway  Enter a valid Gateway address if DHCP is turned off. 
DNS Enter a valid DNS name if DHCP is turned off. 
Apply Press  (Enter) / ► to confirm settings. 
 
— 34 —  
						

							IN134UST/IN136UST User’s Manual 
For simplicity and ease of operation, the projector provides diverse networking and remote management 
features. 
The LAN/RJ45 feature allows the projector to be connected to a network and remotely managed. Available 
remote management controls incl ude: Power On/Off, Video-Source, Br ightness and Contrast settings, 
Sound-Mute, etc.
 
 
 
 
Enter the Projector IP address shown in the SETUP >> Basic >> Lan Control Setting >> Net-
work State menu. Note: DHCP must be on. The LAN/RJ45 Web Control window displays as 
follows: 
 
Preparing Email Alerts   
1.  Make sure that user can access the hom epage of LAN RJ45 function by web browser (for ex-
ample, Microsoft Internet Explorer v6.01/v8.0).  
–  35  –  
						

							IN134UST/IN136UST User’s Manual 
2.  From the Homepage of LAN/RJ45, click Alert Mail Settings. 
 
3.  By default, the input boxes in  Alert Mail Settings are blank.  
 
4.  To setup email alerts, input the following: 

　The  SMTP  field is the mail server for sendi ng out email (SMTP protocol).  
This is a required field. 

　The  To field is the recipient’s email address (for  example, the projector administrator). This 
is a required field.  

　The  Cc field sends a carbon copy of the alert to the specified email address.  
This is an optional field (for example, t he projector administrator’s assistant).  

　The  From field is the sender’s email address (for  example, the projector administrator). 
This is a required field.  

　Select the alert conditions by  checking the desired boxes.  
— 36 —  
						

							IN134UST/IN136UST User’s Manual 
 
Note: Fill in all fields as specified. Select the desired alert condition and click Submit to 
conduct an Email Alert Test . A successful test alerts the designated email accounts. To 
create an email alert, you must select alert  conditions and enter a correct email address.   
Group  and Name  identify the alerting projector and are locate d at the button of the alert mail as shown 
below: 
 
 
–  37  –  
						

							IN134UST/IN136UST User’s Manual 
Factory Reset 
Press the ▲▼ buttons to move up and down in the  Installation II menu. Select the  Factory Reset 
sub menu and press 
 (Enter) /  ► to reset all the menu items to t he factory default values (except 
Language and Security Lock). 
 
Status 
Press the ▲▼  buttons to move up and down in the  Installation II menu. Select the   
Installation II sub menu and press 
 (Enter) /  ► to enter the  Status sub menu.
 
 
ITEM DESCRIPTION 
Active Source  Displays the current active source type. 
Video Information Displays resolution/video information for t
he RGB source and color standard for the 
Video source. 
Lamp Hours 
(Normal, Bright)  Displays the number of normal and br
ight hours that the lamp has been used. 
Software version Displays the Software version of the projector. 
— 38 —  
						

							IN134UST/IN136UST User’s Manual 
– 39  – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in  accordance with the regulations of your local  
authority. 
Warning: 
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to 
do so could result in a severe burn. 
 
Caution: 
In rare cases the lamp bulb may burn out during  normal operation and cause glass dust or shards 
to be discharged outward from the rear exhaust vent. 
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.  
Always keep your face away from the exhaust ve nt so that you do not suffer from the gas and 
broken shards of the lamp. 
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the 
projector. Glass fragments could fall if the lamp has been burned out.  
！ IF A LAMP EXPLODES 
If a lamp explodes, the gas and brok en shards may scatter inside the projector and they may come 
out of the exhaust vent. The gas contains toxic mercury. 
Open windows and doors for ventilation. 
If you inhale the gas or the shards of the broken lamp enter your  eyes or mouth, consult a doctor 
immediately.   
1.  Remove the single screw 
on the lamp compartment 
cover. 
  
						

							IN134UST/IN136UST User’s Manual 
 
2.  Remove the lamp 
compartment cover. 
 
3.  Loosen the two screws 
from the lamp module. 
4.  Lift the module handle up. 
5.  Pull firmly on the module  
handle to remove the lamp 
module. 
 
6.  Reverse steps 1 to 5 to 
install the new lamp 
module.  
While installing, align the 
lamp module with the  
connector and ensure it is 
level to avoid damage. 
Note: The lamp module 
must sit securely in place 
and the lamp connector 
must be connected 
properly before tightening 
the screws. 
 
 
— 40 —  
						

							IN134UST/IN136UST User’s Manual 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 
1.  Press the MENU button to open 
the OSD menu. 
2.  Press the  ◄► buttons to move to 
the Installation II  menu. Press 
the cursor button to move down to 
Advanced . 
3.  Press the ▼▲ buttons to move 
down to Lamp Hour Reset. 
4.  Press the  ► or Enter button.  
A message screen appears. 
5.  Press the arrow keys in the 
following order to reset the lamp 
hours:  ▼▲◄►   
6.  Press the  MENU button to return 
to Installation II. 
 
–  41  –  
						

							IN134UST/IN136UST User’s Manual 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Cleaning the Projector Mirror: 
 
1.  Remove dust the lens with a lens blower  (available from most camera shops) to prevent 
scratching the mirror when it is wiped. 
2. Gently wipe the lens with a  lens cleaning cloth, or alternately, use a lens cleaning tissue in 
conjunction with a small amount of lens cleaning fluid. 
Cautions: 
1. Always turn the projector off and allow to cool for at least 30 minutes prior to cleaning. 
2. Never touch the projector mirror or lens directly by hand. 
3. Only use lens cleaning tissues. Rough cloth can damage the lens and mirror. 
4. Do not use abrasive cleaners, solvents or other harsh chemical cleaners. 
 
—  42 —  
						

							IN134UST/IN136UST User’s Manual 
Cleaning the Case 
Follow these instructions to clean the projector case: 
1. Wipe off dust with a clean dampened cloth. 
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then 
wipe the case. 
3. Rinse all detergent from the cl oth and wipe the projector again. 
Caution: 
To prevent discoloration or fading of the case, do not use abrasive  alcohol-based cleaners. 
 
Warning: 
1. Be sure to turn off and unplug the projector at  least 30 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector inte rior while cleaning, leave it unplugged in a well-
ventilated room for several hours before using. 
4. If a lot of water gets into the projector inte rior when cleaning, have the projector serviced. 
 
 
 
 
 
 
 
 
 
 
– 43  –