InFocus Projector IN134UST User Manual

IN134UST/IN136UST User’s Manual 
Rear view 
1516
123
456
789
10
14 13
12 11
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  Security bar  For security purposes 
2.  Kensington lock Secure to a permanent object with a Kensington® 
Lock system 44 
3.  3D SYNC Connect the 3D IR glasses transmitter 
(Note: For Vivitek brand 3D IR glasses only) 
4.  AUDIO IN Connect an AUDIO cable from the 
audio device. (Supports audio for 
VGA IN-1, VGA IN-2, Composite, and S-video sources.) 
5.  AUDIO OUT  Connect an AUDIO cable to...

IN134UST/IN136UST User’s Manual 
– 5  – 
ITEM  LABEL  DESCRIPTION SEE PAGE 
14.  VIDEO   Connect a composite cable from a video device 
15.  HDMI Connect an HDMI cable from a HDMI device 
16.  RJ45 Connect a LAN cable from Ethernet 
Note: 
If your video equipment has various input sources,  it is recommended that you connect the cables 
in the following order for the best picture quality  : HDMI/DVI, component (thru VGA), Composite. 
 
Warning: 
As a safety precaution, disconnect all power to the...

IN134UST/IN136UST User’s Manual 
Bottom view 
— 6 — 
247.
01
135.51
12221
1
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  Tilt adjustor  Rotate adjuster lever to adjust angle position 14 
2.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
 
Note: 
When installing, ensure that you us
e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of...

IN134UST/IN136UST User’s Manual 
Remote Control Parts 
123
4
5
6
7
89
10
11
12
13
14 15
 
Important: 
1.
 Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the  remote control and the projector. If the path 
between the remote control and the  projector is obstructed, you can bounce the signal off certain 
reflective surfaces such  as projector screens....

IN134UST/IN136UST User’s Manual 
— 8 — 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Up cursor   Navigates and changes settings in the OSD 
2.  Enter  Changes settings in the OSD 
16 
3.  Power  Turns the projector on or off 11 
4.  Right cursor   Navigates and changes settings in the OSD  
5.  Volume +  Increases volume 
6.  Volume -  Decreases volume 
15 
7.  Mute Mutes the built-in speaker 
8.  Freeze  Freeze/unfreezes the on-screen picture 
9.  Source  Selects the input device 
10.  Auto Auto adjustment for...

IN134UST/IN136UST User’s Manual 
– 9  – 
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a...

IN134UST/IN136UST User’s Manual 
— 10 — 
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow (A). Pull out the 
cover  (B). 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution:  
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector...

IN134UST/IN136UST User’s Manual 
Starting and Shutting down the Projector 
1.  Connect the power cord to the 
projector. Connect the other end to 
a wall outlet. 
2.  Turn on the connected devices. 
 
3.  Ensure the POWER LED displays a 
solid green. Then press the POWER  
button 
of the remote to turn on the 
projector.  
 
The projector splash screen displays 
and connected devices are 
detected. 
 
See Setting an Access Password 
(Security Lock)  on page 12 if 
security lock is enabled.

 
4.  If more...

IN134UST/IN136UST User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See  Navigating the 
OSD  on page  16 and Setting the OSD Langua
 ge on page  17 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password,...

IN134UST/IN136UST User’s Manual 
 
4.  Press the ▲▼ buttons to select  
Security Lock . 
5.  Press the ◄► buttons to enable or 
disable security lock function. 
A password dialog box automatically  
appears. 
6.  You can use the cursor buttons 
▲▼◄►  
on IR remote control for password 
entry. You can use any combination 
including the same arrow five times, 
but five characters must be used. 
Press the cursor buttons in any order 
to set the password. Push the  MENU 
button  to exit the  dialog box. 
7....