InFocus Projector IN1142 User Manual

							2
1. Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from overhea\
ting, it is recommended that you install the projector in a location that does not block ventilation. For example, do\
 not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or cabinet that restricts air flow .
2. Do not use the projector near water or moisture. To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture.
3. Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emit heat.
4. Do not use the projector in direct sunlight.
5. Do not use near any appliance generating a strong magnetic field.
6. Do not use the projector in areas susceptible to excessive dust and dirt.
7. Turn off the product before cleaning.
8. Disconnect the power cord if the product is not being used for a long period of time.
9. Ensure that the ambient room temperature is within 0- 40°C (32-104°F).
10. Ensure that relative humidity is 5 - 35°C (41- 95°F), 80% (\
Max.), non-condensing.
11. Do not drop, throw or try to bend your product.
12. Dispose of your projector in an environmentally appropriate manner and according to local disposal laws. Disposing the projector in a fire may cause an explosion.
13. Clean only with dry cloth.
14. Only use attachments/accessories specified by the manufacturer.
15. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to):a Unit has been dropped.a Charger or plug has been damaged.a Liquid has been spilled on the projector.a Projector has been exposed to rain or moisture.a Something has fallen into the projector or something is loose inside.Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Pl\
ease contact your local reseller or service center before you send the unit for repair.
16. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock.
17. Follow all warnings and cautions in this manual and on the projector\
.
18. The unit should only be repaired by appropriate service personnel.
19. The projector surface gets hot when run for long periods of time. Avoid touching the projector until it has been turned off and has cooled down.
Important Safety InStructIon
eye Safety WarnIngS
Avoid staring/facing directly into the projector beam at all times. Keep your back to the beam as much as possible.
A stick or laser pointer is recommended to avoid the need for the user t\
o enter the beam.
When projector is used in a classroom, adequately supervise students whe\
n they are asked to point out something on the screen. 
In order to minimize power, use room blinds to reduce ambient light leve\
ls.
© Copyright 2014. All rights reserved.
The manufacturer reserves the right to make technical changes. The manufacturer assumes no liability for damages incurred directly or i\
ndirectly from errors, omissions, or discrepancies between the device and this documentation.  Other brands or logos are trademarks or registered trademarks of their r\
espective companies.
This device is not intended for use in the direct field of view at visual display workplaces. 
copyrIght / trademark
cautIon
rISk of eXpLoSIon If Battery  IS repLaced 
By an Incorrect type.
When dISpoSIng BatterIeS, Be Sure to 
do So In  an enVIronmentaLL y proper        
manner. 
						

							3
decLaratIon of conformIty
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA
We declare under our sole responsibility that this projector conforms to the following directives and norms:
 EMC Directive 2004/108/EC
 ErP Directive 2009/125/EC
 EMC:   EN 55022: 2010
    EN 55024: 2010
    EN 61000-3-2: 2006+A2:2009
    EN 61000-3-3:2008
 Low Voltage Directive 2006/95/EC
 Safety: IEC 60950-1:2005; EN 60950-1:2006+A12:2011
trademarkS
Apple, Macintosh, iPod, iPod nano, and iPhone are trademarks or register\
ed trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. 
Microsoft, PowerPoint, and Windows are trademarks or registered trademar\
ks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. InFocus, In Focus, INFOCUS (stylized), MondoCenter, Mondopad, BigTouch, JTouch, and LitePro are either registered trademarks or trademarks of InFocus Corporation in the United\
 States and other countries.
NOTE: This product is covered electrical and electronic equipment under the European Union's Waste from Electrical and Electronic Equipment ("WEEE") Directive (2002/96/EC). The WEEE Directive requires that covered equipment be collected and managed separately from typical household waste in all EU member states. Please follow the guidance of y\
our local environmental authority or ask the shop where you purchased the product for collection or recycling options.
fcc WarnIng
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  This device may not cause harmful interference, and (2) this device must accept any interference received, including i\
nterference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference i\
n a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the i\
nstructions, may cause harmful interference to radio communications. How\
ever , there is no guarantee that interference will not occur in a particular install\
ation. If this equipment does cause harmful interference to radio or tel\
evision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by o\
ne or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation m\
ay void authority to operate the equipment.
canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
agency approV aLS
FCC, CE, and CB
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory model IN1142.
Input ratings: AC 110-240V, 9-4A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time without notice. 
						

							4
product oVerVIeW
5V/1A
89
10111213
15
45
7
3
1
6
2
141617
product oVerVIeW
1. Focus Dial2.    Kensington Lock3. Power Button () 4. Up Button ()5. Menu Button (MENU)6.  Left Button ()7.  Down Button ()8. Auto Source Button ()9.  Right Button ()
NoteItems 4~10 are also function buttons. Functions vary depending on the cu\
rrent mode.
10. USB Connector (Service Only)11. HDMI Connector12. Audio Output Connector13.   IR  Receiver14. Lens15.  DC Input16.  Screw Hole for Tripod17. Elevator  Foot 
124
6
8
10
3
5
7
9
Remote Control
1.   Power  Button2.  Up Button3.  
Auto Source Button4. Menu Button5.  Enter Button6.  Left Button7.  Right Button8.  Zoom Button9. Aspect Ratio Button10. Down  Button
poWer on / off
5V/1A
1. Connect the power cord to the DC input jack on the rear of the projector.
2.  Insert the plug at the other end of the power cord into a power outlet.The status LED lights red in standby mode.
3.    Press the Power button () to turn the projector on or off.The status LED turns green when the projector is turned on.5V/1A
Standard Accessory1.  Power cord / AC adaptor2. HDMI cable3.  Remote control (batteries not included)4.  Carrying case
acceSSory oVer VIeW
12
34
Note• IN1142 does not have EZ Suite.• PC, COMP., HDMI, VIDEO, MEDIA, and DOUSB are not supported in IN1142.
Note• The standard accessories may vary in each region due to different applications.• The inclusive power cord varies per region.• CR2025 battery required for remote control. 
						

							5
1.  Connect the HDMI device using an appropriate cable.
2.  After powering on, the projector will automatically detect the HDMI inpu\
t.
5V/1A
adjuSt projected Image heIghtadjuSt the projected Image
The projector is equipped with an elevator foot for adjusting the projec\
ted image height.
To adjust the height:Turn the elevator foot to adjust the projected image position to the desi\
red height.
5V/1A
Adjust the focus until the image is clear.
connect Input Source - hdmI
Note1. All other brand and product names are trademarks or registered trademark\
s of their respective companies. 2. iPod nano/iPod touch/iPhone/iPod classic (version 5 and above)3. Designed for iPod/iPhone/Mobile phone/PMP with TV out functions. Using with devices with audio signal voltage > 0.3Vrms is not recommended.
5V/1A
HDMI
Apple Digital AV Adapter
IPad
IPhone 4
connect Input Source - compoSIte a V In
or
or
NoteIf Auto Keystone is enabled and there are no changes within 2-3 seconds, the projector will automatically adjust the image display via the Auto Keystone function.
Screen Size - Diagonal Projection Distance Screen Size - WidthScreen Size - Height(D)(A)(B)(C)(inch)(mm)(inch)(meter)(inch)(mm)(inch)(mm)2050823.620.60 16.97431 10.59269 40101647.641.21 33.94862 21.18538 60152471.261.81 50.871292 31.81808 80203294.882.41 67.831723 42.401077 1002540118.903.02 84.802154 52.991346 1203048142.523.62 101.772585 63.581615 1403556166.144.22 118.703015 74.211885 1604064189.764.82 135.673446 84.802154 1804572213.785.43 152.643877 95.392423 
NoteThe tripod is an optional accessory. 
Screw a standard tripod into the screw hole on the projector.
Screw hole for tripod
*Standard Tripod
mount the projector 
						

							6
hoW to uSe the menu
Menu Items
PICTURE menu
Menu Operation
pSelect main menu
uEnter current submenu
qHide OSD menu
Submenu Operation
pMove uptAdjust settingqMove downu
Entering Menu Mode 
Press  on the remote control or  on the control panel to enter the menu mode.
SCREEN menu
SETTING menuOPTIONS menu 
						

							7
MenuMenu itemDescription
PICTURE
Display ModeSet the brightness of the display.
BrightnessAdjust the brightness of the image.
ContrastAdjust the contrast of the image.
SharpnessAdjust the sharpness or softness of the image.
Advanced
Set advanced settings for projected image.
GammaAdjust the color gamma differences between the dark and bright portions of the input signal.
BrilliantColorIncrease the brightness by changing the colors.
Color TemperatureSelect the color temperature in the display.
Color SpaceAdjust the color for projected image from a video input signal.
ExitReturn to the PICTURE submenu.
SCREEN
Aspect RatioSelect the aspect ratio of the display.
Digital ZoomDigitally enlarge the projected image.
Auto KeystoneAutomatically adjust the trapezoidal (keystone) distortion of the proj\
ected image.
Manual KeystoneManually adjust the trapezoidal (keystone) distortion of the projected\
 image.
SETTING
LanguageSet the on-screen display language.
Projector PositionSelect the projector position.
Menu PositionSet the display position of the OSD menu.
MuteTemporarily turn off the sound.
VolumeAdjust the volume of the built-in speaker.
OPTIONS
Fan ModeSet the fan speed according to altitude.
Background ColorSet the background screen color when there is no input signal.
InformationDisplay the projector information.
Advanced
Configure other general settings.
Direct Power OnTurn on the projector power automatically when the power supply is switch\
ed on.
Auto Power OffSet the projector to automatically turn off if it is left idle at the preset time.
Reset All SettingsReset all settings to the factory default settings.
ExitReturn to the OPTIONS submenu.
 uSIng the maIn menu
Refer to the below table for menu item details. 
						

							www.infocus.com/supportRegulatory Model: IN1142Part Number: 4J.10801.001
If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local retailer o\
r service center.
Image Problems
P No image appears on-screen 
•   Ensure the power cord is correctly and securely connected.
•   Ensure the pins of connectors are not crooked or broken.
•   Make sure the projector is switched on.
P Image is out of focus
•   
Adjust the Focus Dial.
•    Make sure the projection screen is between the required distance 0.9 to 2.4 meters (2ft 11in to 7ft 10in) from the projector. See page 5.
P Image is too small or too large 
•   Move the projector closer to or further from the screen.
Audio Problems
P No sound
•   During music playback, press t/u on the remote control or / on the control panel.
trouBLeShootIng
NoteWhen the projector temperature reaches 85°C, the projector automatica\
lly shuts down due to the built-in temperature protection. This is not a malfunction. Let the projector cool down before switching it on again.
SpecIfIcatIonS
ItemDescription
ModelIN1142
ImagerDMD WXGA 0.45"
Native Resolution1280x800 WXGA
Projection Distance0.9-2.4 m (3'0" to 7'11")
Projection Screen Size20"-150" (0.5m to 3.81m)
FocusManual
Throw Ratio1.4
Vertical Keystone±40°
Projection ModesTable Top, Front Projection, Rear Projection
Standard Input Resolutionsup to SXGA+ (60Hz)
SDTV/EDTV/HDTV480i, 480p, 576i, 576p, 720p, 1080i
Horizontal Frequency30.5 - 91.1kHz
Vertical Frequency50 - 85Hz
Safety CertificationsCE, CB, FCC
Operating Temperature0 - 40°C (32ºF-104ºF)
Dimensions (WxHxD)170 x 42.5 x 138mm (6.7" x 1.7" x 5.4")
Power InputAC adapter 100~240 V, 50Hz/60Hz
Power ConsumptionTypical 60W@110Vac
Standby