InFocus Projector In102 User Manual

							Operation 41
FUNCTIONDESCRIPTION
Presentation 
TimerReminds the presenter to finish the presentation within a 
certain time frame. See Setting the presentation timer on 
page 33 for details.
LanguageSets the language for the On-Screen Display (OSD) menus. 
See Using the menus on page 21 for details.
Projector 
PositionThe projector can be installed on a ceiling or behind a screen. 
See Choosing a location on page 9 for details.
Auto Power 
OffAllows the projector to turn off automatically if no input signal is 
detected after a set period of time. See Setting Auto Power 
Off on page 45 for details.
Blank TimerSets the image blank time when the Blank feature is activated, 
once elapsed the image will return to the screen. See Hiding 
the image on page 34 for details.
Panel Key 
LockDisables or enables all panel key functions except POWER 
on the projector and keys on the remote control. See Locking 
control keys on page 34 for details.
Timer 
ControllerSets the auto-shutdown timer. The timer can be set to a value 
between 30 minutes and 12 hours.
Splash 
ScreenAllows you to select which logo screen will display during 
projector start-up. Three options are available: InFocus logo, 
Black screen, or Blue screen.
4. SYSTEM SETUP: Basic 
menu
II 
						

							Operation 42
FUNCTIONDESCRIPTION
Quick 
Cooling
Selecting On enables the function and the projector cooling 
time will be shortened to a few seconds.
If you attempt to restart the projector right after the quick 
cooling process, it may not be turned on successfully and will 
rerun its cooling fans.
High Altitude 
ModeA mode for operation in high altitude areas. See Operating in a 
high altitude environment on page 35 for details.
Audio 
SettingsMute
Volume
See Adjusting the sound on page 35 for details.
Menu 
Settings
Menu display time
Sets the length of time the OSD will remain active after your last 
key press. The range is from 5 to 30 seconds in 5-second 
increments.
Menu position
Sets the On-Screen Display (OSD) menu position.
Closed 
Caption
Closed Caption Enable
Activates the function by selecting On when the selected input 
signal carries closed captions.
 Captions: An on-screen display of the dialogue, narration, 
and sound effects of TV programs and videos that are 
closed captioned (usually marked as CC in TV listings).
Caption Version
Selects a preferred closed captioning mode. To view captions, 
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the 
primary language in your area).
5. SYSTEM SETUP: Advanced menu 
						

							Operation 43
FUNCTIONDESCRIPTION
VGA Out
Selecting On enables the function. The projector can output a 
VGA signal when it is in standby mode and the D-SUB IN and 
D-SUB OUT sockets are correctly connected to devices. See 
Connecting a monitor on page 15 for how to make the 
connection.
Enabling this function slightly increases the standby power 
consumption.
Lamp 
Settings
Lamp mode
See Setting Lamp mode as Economic on page 45 for details.
Reset lamp timer
See Resetting the lamp timer on page 49 for details.
Equivalent lamp hour
S
ee Getting to know the lamp hour on page 45 for details 
on how the total lamp hour is calculated.
Security 
Settings
Change password
You will be asked to enter the current password before 
changing to a new one.
Power on lock
See Utilizing the password function on page 22 for details.
Reset All 
SettingsReturns all settings to the factory preset values.
The following settings will still remain: Position, Phase, H. Size, 
User, Language, Projector Position, High Altitude Mode, 
Security Settings.
Current 
System 
Status
Source
Shows the current signal source.
Preset Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
5. SYSTEM SETUP: Advanced menu
6. INFORMATION menu 
						

							Maintenance 44
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular 
basis is to keep the lens clean.
Never remove any parts of the projector except the lamp. If your projector needs 
service, contact InFocus Corporation (www.infocus.com/support) or your dealer for 
assistance.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. 
 Use a canister of compressed air to remove dust.
 If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with 
lens cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown 
procedure as described in Shutting down the projector on page 36 and unplug the 
power cord.
 To remove dirt or dust, wipe the case with a soft, lint-free cloth.
 To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral 
pH detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions 
below:
 Make sure the temperature and humidity of the storage area are within the 
recommended range for the projector. Please refer to Specifications on page 
52 or consult your dealer about the range.
 Retract the adjuster feet.
 Remove the battery from the remote control.
 Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. 
						

							Maintenance 45
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is 
automatically calculated by the built-in timer. The timer displays lamp hours used in 
Normal mode, plus equivalent Economic mode hours. Equivalent Economic 
mode hours are calculated as follows:
1 lamp hour (in Normal mode) = 1.33 lamp hours (in Economic mode)
See Setting Lamp mode as Economic below for more information on Economic mode.
To obtain the lamp hour information:
1. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: 
Advanced menu is highlighted.
2. Press  to highlight Lamp Settings and press MODE/ENTER. The Lamp 
Settings page displays.
3. You will see the Equivalent lamp hour information displaying on the menu.
4. To leave the menu, press MENU/EXIT.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as 
possible, you can do the following settings via the OSD menu.
Setting Lamp mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If 
the Economic mode is selected, the light output will be reduced and result in 
darker projected pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set 
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > 
Lamp mode menu and press  / .
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is 
detected after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off 
menu and press  / . The time period can be set from 5 to 30 minutes in 5-minute 
increments. If the preset time lengths are not suitable for your presentation, select 
Disable. The projector will not automatically shut down in a certain time period. 
						

							Maintenance 46
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time 
to replace the lamp, please install a new lamp or consult your dealer. An old lamp 
may cause a malfunction in the projector and in some instances the lamp may 
explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
still lights up after turning the power back on, please contact your dealer. See Indicators on 
page 50 for details.
The following lamp warning displays will remind you to change the lamp.
StatusMessage
The lamp has been in operation for 3500 
hours. Install a new lamp for optimal 
performance. If the projector is normally run 
with Economic selected (See Setting Lamp 
mode as Economic on page 45), you may 
continue to operate the projector until the 
3950 hour lamp warning appears.
The lamp has been in operation for 3950 
hours. A new lamp should be fitted to avoid 
the inconvenience when the projector runs 
out of lamp time.
The lamp has been in operation for 4000 
hours.
It is strongly recommended that you replace 
the lamp at this age. The lamp is a 
consumable item. The lamp brightness 
diminishes with use. This is normal lamp 
behavior. You can replace the lamp whenever 
you notice that the brightness level has 
significantly diminished. If the lamp is not 
replaced beforehand, it must be replaced 
after 4000 hours usage.
The lamp life has expired. The lamp must be 
replaced.
OK
Order Replacement Lamp
Lamp > 3500 Hours
Notice
OK
Replace Lamp Soon 
Lamp > 3950 Hours
Notice
OK
Replace Lamp Now 
Lamp > 4000 Hours
Lamp usage time exceeded
Notice
OK
Out of Lamp Usage Time
Replace lamp (refer to User Manual)
Then reset lamp timer
Notice 
						

							Maintenance 47
Replacing the lamp
WARNING
Hg - Lamp contains mercury. Manage in accordance with local 
disposal laws. See www.lamprecycle.org
• To reduce the risk of electrical shock, always turn the projector off and disconnect the 
power cord before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution 
when removing lamp glass that has shattered into sharp pieces. Before replacing the 
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp 
edges in the lamp compartment. Wash hands after lamp replacement.
• Only InFocus certified lamps are tested with this projector.  Use of other lamps may cause 
electrical shock and fire.
1. Turn the power off and disconnect 
the projector from the wall socket. If 
the lamp is hot, avoid burns by 
waiting for approximately 45 
minutes until the lamp has cooled.
2. Turn the projector over. Then loosen 
the screws on the lamp cover.
3. Remove the lamp cover from the 
projector.
WARNING
• Do not turn the power on with the lamp 
cover removed.
• Do not insert your fingers between the 
lamp and the projector. The sharp edges 
inside the projector may cause injuries.
4. Loosen the screw that secures the 
lamp. 
						

							Maintenance 485. Pull out the lamp connector from a 
slot in the lamp compartment. 
Disconnect it from the projector as 
illustrated.
6. Lift the handle so that it stands up. 
Use the handle to slowly pull the 
lamp out of the projector.
CAUTION
• Pulling it too quickly may cause the lamp 
to break and scatter broken glass in the 
projector.
• Do not place the lamp in locations where 
water might splash on it, children can 
reach it, or near flammable materials.
• Do not insert your hands into the projector 
after the lamp is removed. If you touch the 
optical components inside, it could cause 
color unevenness and distortion of the 
projected images.
7. Insert the new lamp into the 
lamp compartment and 
make sure it fits in the 
projector.
8. Reconnect the lamp 
connector and place it back 
into its slot to be flush with 
the projector.
1
2
2 
						

							Maintenance 49 13. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-
Screen Display (OSD) menu. Go to the 
SYSTEM SETUP: Advanced > Lamp 
Settings menu. Press MODE/ENTER. 
The Lamp Settings page displays. 
Press  to highlight Reset lamp timer 
and press MODE/ENTER. A warning message displays asking if you want to 
reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp 
time will be reset to 0.
CAUTION
Do not reset if the lamp is not new or replaced as this could cause damage. 
9. Tighten the screw that secures the 
lamp.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screw.
10. Ensure the handle is fully laid flat 
and locked in place.
11. Replace the lamp cover on the 
projector.
12. Tighten the screws that secure the 
lamp cover.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screws.
Reset Lamp Timer?
Reset
Cancel
Notice 
						

							Maintenance 50
Indicators
LightStatus & Description
PowerTe m pLamp
Power events
Orange Orange OrangeThe projector has just been connected to a power 
outlet.
Orange Off OffStand-by mode
Green
FlashingOff OffPowering up
Green Off OffNormal operation
Orange
FlashingOff Off
1. The projector needs 90 seconds to cool down as it 
was abnormally shut down without the normal 
cooling down process. Or
2. The projector needs to cool for 90 seconds after 
the power is turned off.
Orange
FlashingOff OffThe projector has shutdown automatically. If you try to 
re-start the projector, it will shutdown again. Please 
contact your dealer for assistance.
Lamp events
Orange
FlashingOff RedThe projector has shutdown automatically. If you try to 
re-start the projector, it will shutdown again. Please 
contact your dealer for assistance.
Off Off Red1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
Green Off RedThe lamp life has expired. Please replace the lamp.
Thermal events
Off Red Off
The projector has shutdown automatically. If you try to 
re-start the projector, it will shutdown again. Please 
contact your dealer for assistance.
Off Red Red
Off Red Green
Off Red Orange
Red Red Red
Red Red Green
Red Red Orange
Green Red Red
Green Red Green
Green Red Orange
Orange Red Red
Orange Red Green
Orange Red Orange
Off Green Red
Off Green Green