InFocus Projector In102 User Manual

							Positioning your projector 11
How to determine the position of the projector 
for a given screen size
1. Select your screen size.
2. Refer to the table and find the closest match to your screen size in the left 
columns labelled 4:3 screen diagonal. Using this value, look across this row 
to the right to find the corresponding average distance from screen value in 
the column labelled Average. This is the projection distance.
3. On that same row, look across to the right column and make note of the 
Vertical offset value. This will determine the final vertical offset placement of 
the projector in relation to the edge of the screen.
4. The recommended position for the projector is aligned perpendicular to the 
horizontal center of the screen, at the distance from the screen determined in 
step 2 above, and offset by the value determined in step 3 above.
For example, if you are using a 108-inch screen, the average projection distance is 
4320 mm (170”) and with a vertical offset of 82 mm (3.2”).
If you place the projector in a different position (to that recommended), you will have 
to tilt it down or up to center the image on the screen. In these situations, some 
image distortion will occur. Use the Keystone function to correct the distortion. See 
Correcting keystone on page 26 for details.
How to determine the recommended screen size 
for a given distance
This method can be used for situations where you have purchased this projector 
and would like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room. 
1. Measure the distance between the projector and where you want to position 
the screen. This is the projection distance.
2. Refer to the table and find the closest match to your measurement in the 
average distance from screen column labelled Average. If the min and max 
values are available on the table, check that your measured distance is 
between the min and max distances listed on either side of the average 
distance value.
3. Using this value, look across that row to the left to find the corresponding 
screen diagonal listed in that row. That is the projected image size of the 
projector at that projection distance.
4. On that same row, look across to the right column and make note of the 
Vertical offset value. This will determine the final placement of the screen in 
relation to the horizontal plane of the projector. 
For example, if your measured projection distance was 4.5 m (177”), the closest 
match in the Average column is 4320 mm (170”). Looking across this row shows 
that a 108-inch screen is required. 
						

							Positioning your projector 12
Projection dimensions
Refer to Dimensions on page 53 for the center of lens dimensions of this projector 
before calculating the appropriate position.
There is 3% tolerance among these numbers due to optical component variations. InFocus 
recommends that if you intend to permanently install the projector, you should physically test 
the projection size and distance using the actual projector before you permanently install it, 
so as to make allowance for this projectors optical characteristics. This will help you 
determine the exact mounting position so that it best suits your installation location.
4:3 screen diagonalRecommended projection distance from 
screenVertical offset
Min length 
(with max. 
zoom)AverageMax length 
(with min. 
zoom)
Feet Inches mm mm Inches mm Inches mm Inches mm Inches
4 48 1219 1829 72 1920 76 2011 79 37 1.4
59 1500 2250 89 2362 93 2475 97 45 1.8
5 60 1524 2286 90 2400 94 2514 99 46 1.8
6 72 1829 2743 108 2880 113 3017 119 55 2.2
79 2000 3000 118 3150 124 3300 130 60 2.4
7 84 2134 3200 126 3360 132 3520 139 64 2.5
8 96 2438 3657 144 3840 151 4023 158 73 2.9
98 2500 3750 148 3937 155 4124 162 75 3.0
9 108 2743 4114 162 4320 170 4526 178 82 3.2
118 3000 4499 177 4724 186 4949 195 90 3.5
10 120 3048 4571 180 4800 189 5029 198 91 3.6
138 3500 5249 207 5512 217 5774 227 105 4.1
12 144 3658 5486 216 5760 227 6034 238 110 4.3
157 4000 5999 236 6299 248 6599 260 120 4.7
15 180 4572 6857 270 7200 283 7543 297 137 5.4
197 5000 7499 295 7874 310 8249 325 150 5.9
18 216 5486 8229 324 8640 340 9051 356 165 6.5
236 6000 8999 354 9449 372 9899 390 180 7.1
25 300 7620 11429 450 12000 472 12571 495 229 9.0
Projection distanceCenter of lens Screen
Vertical offset Maximum zoom
Minimum zoom 
						

							Connection 13
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted. 
In the connections shown below, some cables may not be included with the projector (see 
Shipping contents on page 4). Additional cables can be purchased from InFocus.com in 
select areas, your dealer and/or from a commercial electronics store. 
						

							Connection 14
Connecting a computer or monitor
Connecting a computer
The projector provides a VGA input socket that allows you to connect it to both 
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are 
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket 
of the computer.
2. Connect the other end of the VGA cable to the COMPUTER IN1/COMPUTER 
IN2 signal input socket on the projector.
3. If you wish to make use of the projector (mixed mono) speaker in your 
presentations, take a suitable audio cable and connect one end of the cable to 
the audio output socket of the device, and the other end to the AUDIO IN 
socket of the projector.
4. If you wish, you can use another suitable audio cable and connect one end of 
the cable to the AUDIO OUT jack of the projector, and the other end to your 
external speakers (not supplied).
Once connected, the audio can be controlled by the projector On-Screen 
Display (OSD) menus. See Adjusting the sound on page 35 for details.
The built-in speaker will be muted when the AUDIO OUT jack is connected.
The final connection path should be like that shown in the following diagram:
Many notebooks do not turn on their external video ports when connected to a projector. 
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a 
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press 
FN and the labeled function key simultaneously. Refer to your notebooks documentation to 
find your notebooks key combination.
Notebook or desktop computer
Audio cable VGA cable
Audio cable Speakers 
						

							Connection 15
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the 
screen, you can connect the MONITOR OUT signal output socket on the projector 
to an external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in Connecting a computer 
on page 14.
2. Take a suitable VGA cable (only one supplied) and connect one end of the 
cable to the D-Sub input socket of the video monitor. 
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A 
cable and connect the DVI end of the cable to the DVI input socket of the video 
monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the 
projector.
The final connection path should be like that shown in the following diagram:
• The D-Sub output only works when an appropriate D-Sub input 
is made to the COMPUTER IN1 jack.
• If you wish to use this connection method when the projector is in standby mode, make 
sure the VGA Out function is turned on in the SYSTEM SETUP: Advanced menu. See VGA 
Out on page 43 for details.
Monitor
(VGA) (DVI-A)or
(VGA) 
						

							Connection 16
Connecting video source devices
You can connect your projector to various video source devices that provide any 
one of the following output sockets:
 Component video
 S-Video
 Video (composite)
You only need to connect the projector to a single video source device; however 
each provides a different level of video quality. The method you choose will most 
likely depend upon the availability of matching terminals on both the projector and 
the video source device as described below:
Best video quality
The best available video connection method is Component video (not to be 
confused with composite video). Digital TV tuner and DVD players output 
Component video natively, so if available on your devices, this should be your 
connection method of choice in preference to (composite) video.
See Connecting a Component video source device on page 17 for how to connect 
the projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard 
composite video. If you have both composite video and S-Video output terminals on 
your video source device, you should elect to use the S-Video option.
See Connecting an S-Video source device on page 18 for how to connect the 
projector to an S-Video device.
Good video quality
Composite video is analog video and will result in a perfectly acceptable, but less 
than optimal result from your projector. The other methods described above provide 
better video quality.
See Connecting a composite video source device on page 19 for how to connect 
the projector to a composite video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic 
audio functionality accompanying data presentations for business purposes only. It 
is not designed for, nor intended for stereo audio reproduction use as might be 
expected in home theater or home cinema applications. Any stereo audio input (if 
provided), is mixed into a common mono audio output through the projector 
speaker.
If you have a separate sound system, you will most likely want to connect the audio 
output of your video source device to that sound system, instead of to the mono 
audio projector. The audio connections are provided for informational purposes 
only. You need not connect audio to the projector if there is an alternate sound 
system available, or if audio is not required. 
						

							Connection 17
Connecting a Component video source device
Examine your video source device to determine if it has a set of unused Component 
video output sockets available: 
 If so, you can continue with this procedure.
 If not, you will need to reassess which method you can use to connect to the 
device.
To connect the projector to a Component video source device:
1. Take a Component video to VGA (D-Sub) adaptor cable and connect the end 
with 3 RCA type connectors to the Component video output sockets of the 
video source device. Match the color of the plugs to the color of the sockets; 
green to green, blue to blue, and red to red.
2. Connect the other end of the Component video to VGA (D-Sub) adaptor cable 
(with a D-Sub type connector) to the COMPUTER IN1/COMPUTER IN2 
socket on the projector.
3. If you wish to make use of the projector (mixed mono) speaker in your 
presentations, take a suitable audio cable and connect one end of the cable to 
the audio output socket of the device, and the other end to the AUDIO IN 
socket of the projector.
4. If you wish, you can use another suitable audio cable and connect one end of 
the cable to the AUDIO OUT jack of the projector, and the other end to your 
external speakers (not supplied).
Once connected, the audio can be controlled by the projector On-Screen 
Display (OSD) menus. See Adjusting the sound on page 35 for details.
The built-in speaker will be muted when the AUDIO OUT jack is connected.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting audio on page 16 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
RS-232
MONITOR OUT COMPUTER IN1 COMPUTER IN2 VIDEO S -VIDEO AUDIO IN  AUDIO OUT
AV device
Component video
to VGA (D-Sub)
adaptor cable
Audio cableSpeakers
Audio cable 
						

							Connection 18
Connecting an S-Video source device
Examine your video source device to determine if it has an unused S-Video output 
socket available: 
 If so, you can continue with this procedure.
 If not, you will need to reassess which method you can use to connect to the 
device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of 
the video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the 
projector.
3. If you wish to make use of the projector (mixed mono) speaker in your 
presentations, take a suitable audio cable and connect one end of the cable to 
the audio output socket of the device, and the other end to the AUDIO IN 
socket of the projector. 
4. If you wish, you can use another suitable audio cable and connect one end of 
the cable to the AUDIO OUT jack of the projector, and the other end to your 
external speakers (not supplied).
Once connected, the audio can be controlled by the projector On-Screen 
Display (OSD) menus. See Adjusting the sound on page 35 for details.
The built-in speaker will be muted when the AUDIO OUT jack is connected.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting audio on page 16 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• If you have already made a Component video connection between the projector and this S-
Video source device using Component video connections, you need not connect to this 
device using an S-Video connection as this makes an unnecessary second connection of 
poorer picture quality. See Connecting video source devices on page 16 for details.
RS-232
MONITOR OUT COMPUTER IN1 COMPUTER IN2 VIDEO S -VIDEO AUDIO IN  AUDIO OUT
AV device
S-Video cable
Audio cable
Audio cable 
						

							Connection 19
Connecting a composite video source device
Examine your video source device to determine if it has a set of unused composite 
video output sockets available:
 If so, you can continue with this procedure.
 If not, you will need to reassess which method you can use to connect to the 
device.
To connect the projector to a composite video source device:
1. Take a video cable and connect one end to the composite video output socket 
of the video source device.
2. Connect the other end of the video cable to the VIDEO socket on the 
projector.
3. If you wish to make use of the projector (mixed mono) speaker in your 
presentations, take a suitable audio cable and connect one end of the cable to 
the audio output socket of the device, and the other end to the AUDIO IN 
socket of the projector. 
4. If you wish, you can use another suitable audio cable and connect one end of 
the cable to the AUDIO OUT jack of the projector, and the other end to your 
external speakers (not supplied).
Once connected, the audio can be controlled by the projector On-Screen 
Display (OSD) menus. See Adjusting the sound on page 35 for details.
The built-in speaker will be muted when the AUDIO OUT jack is connected.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting audio on page 16 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• You need only connect to this device using a composite video connection if Component 
video and S-Video inputs are unavailable for use. See Connecting video source devices 
on page 16 for details.
RS-232
MONITOR OUT COMPUTER IN1 COMPUTER IN2 VIDEO S -VIDEO AUDIO IN  AUDIO OUT
AV  d e v i c e
Video cable 
Audio cable
Audio cable 
						

							Operation 20
Operation
Starting up the projector
1. Plug the power cord into the projector and 
into a wall socket. Turn on the wall socket 
switch, if applicable. Check that the POWER 
indicator light on the projector lights 
orange after power has been applied.
2. Remove the lens cap. If it is closed, it could 
become deformed due to the heat 
produced by the projection lamp.
3. Press POWER on the projector or 
remote control to start the projector. The 
POWER indicator light flashes green and 
stays green when the projector is on.
The start up procedure takes about 30 
seconds. In the later stage of start up, a 
startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
• If the projector is still hot from previous activity, it will run the cooling fan for 
approximately 90 seconds before energizing the lamp. 
• To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before 
turning it off.
4. If you are prompted for a password, press the arrow keys to enter a six-digit 
password. See Utilizing the password function on page 22 for details.
5. Switch all of the connected equipment on.
6. The projector will start to search for input signals. The current input signal 
being scanned displays in the upper left corner of the screen. If the projector 
doesnt detect a valid signal, the message No Signal will continue displaying 
until an input signal is found.
You can also press SOURCE on the projector or remote control to select your 
desired input signal. See Switching input signal on page 24 for details.
If the frequency/resolution of the input signal exceeds the projectors operating range, you will 
see the message Out of Range displayed on a blank screen. Please change to an input signal 
which is compatible with the projectors resolution or set the input signal to a lower setting. 
See Timing chart on page 53 for details.
II