Home > InFocus > Projector > InFocus Projector CP-S245 CP-X255 User Manual

InFocus Projector CP-S245 CP-X255 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual InFocus Projector CP-S245 CP-X255 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 493 InFocus manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    51
    
    Troubleshooting
    Regarding the indicator lamps (continued)
    POWER 
    indicatorLAMP indicatorTEMP indicatorDescription
    Blinking
    In Red
    or
    Lighting
    In Red
    Turned
    off
    Blinking
    In Red
    The cooling fan is not operating.
    Please turn the power off, and allow the projector to 
    cool down at least 20 minutes. After the projector has 
    sufficiently cooled down, please make confirmation 
    that no foreign matter has become caught in the fan, 
    etc., and then turn the power on again.
    If the same indication is displayed after the remedy, 
    please contact your dealer or service company.
    Blinking
    In Red
    or
    Lighting
    In Red
    Turned
    off
    Lighting
    In Red
    There is a possibility that the interior portion 
    has become heated.
    Please turn the power off, and allow the projector to 
    cool down at least 20 minutes. After the projector has 
    sufficiently cooled down, please make confirmation of 
    the following items, and then turn the power on again.
    • Is there blockage of the air passage aperture?
    • Is the air filter dirty?
    • Does the peripheral temperature exceed 35°C?
    If the same indication is displayed after the remedy, 
    please set FAN SPEED of the SERVICE item in the 
    OPTION menu to HIGH.
    Lighting
    In Green
    Simultaneous
    blinking in Red
    It is time to clean the air filter.
    Please immediately turn the power off, and clean or 
    change the air filter referring to the section “Air Filter”. 
    After cleaning or changing  the air filter, please be sure 
    to reset the filter timer. After the remedy, reset the 
    power to ON.
    Blinking in 
    Green for 
    approx. 3 
    seconds Turned
    off
    Turnedoff
    At least 1 “Power ON” schedule is saved to the 
    projector.
    (Please refer to the User’s Manual-Network Functions: 
    Schedule Settings for more information.)
    NOTE  • When the interior portion has become overheated, for safety 
    purposes, the power source is automatically turned off, and the indicator lamps 
    may also be turned off
    . In such a case, press the “” (OFF) side of the power 
    switch, and wait at least 45 minutes.  After the projector has sufficiently cooled 
    down, please make confirmation of the attachment state of the lamp and lamp  cover, and then turn the power on again. 
    						
    							
    52
    
    Troubleshooting
    Phenomena that may be easy to be mistaken for machine defects
    WARNING  ►Never use the projector if abnormal operations such as 
    smoke, strange odor, excessive sound, damaged casing or elements or cables, 
    penetration of liquids or foreign matter, etc. should occur. In such cases, 
    immediately turn off the power switch and then disconnect the power plug from 
    the power outlet. After making sure that the smoke or odor has stopped, contact 
    your dealer or service company.
    1. Before requesting repair, please check in 
    accordance with the following chart.  This 
    operation sometimes resolves your problem.
    If the situation cannot be corrected, 
    2. The projector’s microprocessor may need to be 
    reset. Please push the Restart switch by using a cocktail stick or similar and 
    the projector will restart.
    3. Some setting may be wrong.  Please use the FACTORY RESET function of the 
    SERVICE item in the OPTION menu
     (39 ) to reset all settings to factory default.
    Then, if the problem is not removed after the remedy, please contact your dealer 
    or service company.
    PhenomenonCases not involving a machine defectReference
    page
    Power does not 
    come on.
    The electrical power cord is not plugged in.Correctly connect the power cord.14
    The power switch is not set to the on position.Set the power switch to [ | ] (On).17
    The main power source has been interrupted during operation such as by a power outage (blackout), etc.Please turn the power off, and allow the projector to cool down at least 2 minutes, then turn the power on again.
    17
    Either there is no lamp and/or lamp cover, or either 
    of these has not been properly fixed.
    Please turn the power off, and allow the projector to cool down 
    at least 45 minutes. After the projector has sufficiently cooled 
    down, please make confirmation of the attachment state of the 
    lamp and lamp cover, and then turn the power on again.43, 44
    Neither sounds
    nor pictures are
    outputted.
    The signal cables are not correctly connected.Correctly connect the connection cables.12, 13
    Signal source does not correctly work.Correctly set up the signal source device by referring to the manual of the source device.–
    The input changeover settings are mismatched.Select the input signal, and correct the settings.18
    The RGB IN2 port is assigned to an RGB out while an RGB input signal is inputted to the port.Push the RGB IN OUT switch to switch the function  of the port.12 
    						
    							
    53
    
    Phenomena that may be easy to be mistaken for machine defects (continued)
    PhenomenonCases not involving a machine defectReference
    page
    Sound does not 
    come out.
    The signal cables are not correctly connected.Correctly connect the audio cables.12,13
    The MUTE function is working.Restore the sound pressing the MUTE or VOLUME button on the remote control.18
    The volume is adjusted to an extremely low level.Adjust the volume to a higher level using the menu function or the remote control.18
    The AUDIO setting is not correct.Correctly set the AUDIO item in the SETUP menu.34
    No pictures are 
    displayed.
    The lens cap is attached.Remove the lens cover.17
    The signal cables are not correctly connected.Correctly connect the connection cables.12, 13
    The brightness is adjusted to an extremely low level.Adjust BRIGHTNESS to a higher level using the menu function or the remote control.25
    The computer cannot detect the projector as a plug 
    and play monitor.
    Make sure that the computer can detect a plug and play 
    monitor using another plug and play monitor.11
    Video screen
    display freezes.The FREEZE function is working.Press the FREEZE button to restore the screen to normal.22
    Colors have a
    faded- out
    appearance, or
    Color tone is  poor.
    Color settings are not correctly adjusted.Perform picture adjustments by changing the COLOR 
    TEMP, COLOR, TINT and/or COLOR SPACE settings, using the menu functions.
    25, 28, 
    32
    COLOR SPACE setting is not suitable.Change the COLOR SPACE setting to AUTO, RGB, SMPTE240, REC709 or REC601. 32
    Troubleshooting 
    						
    							
    54
    
    Phenomena that may be easy to be mistaken for machine defects (continued)
    PhenomenonCases not involving a machine defectReference
    page
    Pictures appear 
    dark.
    The brightness and/or contrast are adjusted to an extremely low level.Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.
    25
    The WHISPER function is working.Select NORMAL for the WHISPER item in the SETUP menu.25
    The lamp is approaching the end of its product lifetime.Replace the lamp.43, 44
    Pictures appear
    blurry.
    Either the focus and/or horizontal phase settings are not properly adjusted.Adjust the focus using the focus ring, and/or H PHASE using the menu function.
    30
    The lens is d irty or misty.Clean the lens referring to the section “Caring for the lens”.48
    Troubleshooting
    NOTE  • Although bright spots or dark spots may appear on the screen, this 
    is a unique characteristic of liquid crystal displays, and it does not constitute or 
    imply a machine defect. 
    						
    							
    55
    
    Warranty And After-Ser vice
    Warranty and after-service
    If a problem occurs with the equipment, first refer to the “Troubleshooting” and run 
    through the suggested checks. If this does not resolve the problem, please contact your 
    dealer or service company. They will tell you what warranty condition is applied.
    Specifications
    Specifications
    NOTE  • These specifications are subject to change without notice.
    Item Specification
    Product nameLiquid crystal projector
    Liquid
    Crystal
    panel
    Panel size1.5 cm (0.6 type)
    Drive systemTFT active matrix
    PixelsCP-S245 : 480,000 pixels (800 horizontal x 600 vertical)
    CP-X255 : 786,432 pixels (1024 horizontal x 768 vertical)
    LensZoom lens F=1.7 ~ 1.9 f=18.9 ~ 22.6 mm
    Lamp180W UHB
    Speaker1W x 1
    Power SupplyAC100-120V/3.1A, AC220-240V/1.7A
    Power Consumption290W
    Temperature range
    5 ~ 35°C (Operating)
    Size
    306 (W) x 86 (H) x 249 (D) mm 
    (Not including protruding parts)
    • Please refer to the following figure.
    Weight (mass)
    3.0 kg
    Ports
    Optional 
    parts
    LampDT00731
    Air filter
    NJ22222
    Others • Please consult your dealer.
    RGB input: RGB IN1 ..D-sub 15pin mini x1RGB IN2 /OUTD-sub 15pin mini   ................x1(select RGB IN2 or RGB OUT)
    Audio input:AUDIO 1 ..........Stereo mini x1AUDIO 2 ..................... RCA x2
    Audio output:
    AUDIO OUT  ...Stereo mini x1 Video input:
    COMPONENT VIDEO 
      (Y, 
    CB/PB, CR/PR) ......
    RCA x3 
    S-Video  ................................1
    Video  ....................................1
    Communication port: CONTROL  ............D-sub 9pin x1USB .......................USB(B) x1 LAN ..........................RJ-45 x1 
    						
    							
    56
    Specifications
    Specifications (continued)
    Y R
    L
    AUDIO IN2AUDIO OUTCONTROL RGB IN1
    RGB IN2 USB
    RGB OUTAUDIO IN1LANLINKACTVIDEOS-VIDEO
    CB/PBCR/PRK
    306 mm
    249 
    mm
    100
     mm86 mm 
    						
    All InFocus manuals Comments (0)

    Related Manuals for InFocus Projector CP-S245 CP-X255 User Manual