Home > InFocus > Projector > InFocus Projector CP-S245 CP-X255 User Manual

InFocus Projector CP-S245 CP-X255 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual InFocus Projector CP-S245 CP-X255 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 493 InFocus manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    21
    
    Using the magnify feature
    1. Press the ON button of MAGNIFY on the remote control.   
    The “MAGNIFY” indication will appear on the screen 
    (although the indication will disappear in several seconds with 
    no operation), and the projector will enter the MAGNIFY mode.
    2. Use the cursor buttons ▲/▼ to adjust the zoom level. 
    To move the zoom area
    , press the POSITION button in the MAGNIFY mode, 
    then use the cursor buttons ▲/▼/◄/► to move the area.  And to finalize the 
    zoom area, press the POSITION button again.
    To exit the MAGNIFY mode and restore the screen to normal, press the O
    FF 
    button of MAGNIFY on the remote control.
     
    ●  The projector automatically exits the MAGNIFY mode when the input signal is 
    changed, or when the display condition is changed. 
    ● Although in the MAGNIFY mode, the keystone distortion condition may vary, it 
    will be restored when the projector exits the MAGNIFY mode.
    Operating
    Correcting the keystone distortions
    1. Press the KEYSTONE button on the remote control.  A 
    dialog will appear on the screen to aid you in correcting the 
    distortion.
    2. Use  the  cursor  buttons ▲/▼  to correct  the  distortion. 
    To  close  the  dialog  and  complete  this  operation,  press  the 
    KEYSTONE  button  again.
      Even  if  you  don’t  do  anything,  the 
    dialog will automatically disappear after a few seconds.
    ● The adjustable range for correction will vary among inputs. For some input, this 
    function may not work well.
    ● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the 
    SETUP menu, if the projector screen is inclined or angled downward, this 
    function may not work correctly.
    ● When the zoom adjustment is set to the TELE (telephoto focus), this correction  may be excessive. This function should be used when the zoom adjustment is 
    set to the WIDE (wide-angle focus) whenever possible.
    HOMEPAGE UP
    PAGE DOWNEND
    VIDEO RGBSEARCH
    FREEZE
    OFF
    ONMAGNIFY
    ASPECT AUTOBLANK
    MUTE
    VOLUME
    KEYSTONE
    POSITION
    ES
    C ENTE
    RMENU
    RESE
    T
    HOMEPAGE UP
    PAGE DOWNEND
    VIDEO RGBSEARCH
    FREEZE
    OFF
    ONMAGNIFY
    ASPECT AUTOBLANK
    MUTE
    VOLUME
    KEYSTONE
    POSITION
    ES
    C ENTE
    RMENU
    RESE
    T 
    						
    							
    22
    
    Freezing the screen
    1. Press the FREEZE button on the remote control.  
    The “FREEZE” indication will appear on the screen, and the 
    projector will enter the FREEZE mode.
    To exit the 
    FREEZE mode and restore the screen to normal, 
    press the FREEZE button again. 
    ● The projector automatically exits the FREEZE mode when the input signal  changes, or when one of the projector’s buttons or the remote control buttons 
    of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME, 
    MUTE, KEYSTONE, POSITION and MENU is pressed.
    ● If the projector continues projecting a still image for long time, the LCD panel 
    might possibly be printed. Do not leave the projector in the FREEZE mode for 
    too long.
    Temporarily blanking the screen
    1. Press the BLANK button on the remote control.  
    The blank screen will be displayed instead of the screen of 
    input signal. Please refer to the BLANK item in the SCREEN 
    menu (35).
    To exit the blank screen and return to the input signal screen, press the  
    BLANK button again. 
    ● The projector automatically returns to the input signal screen when the input 
    signal is changed, or  when one of the projector’s buttons or the remote control 
    buttons is pressed.
    Operating
    HOMEPAGE UP
    PAGE DOWNEND
    VIDEO
    RGBSEARCH
    FREEZE
    OFF
    ONMAGNIFY
    ASPECT AUTOBLANK
    MUTE
    VOLUME
    KEYSTONE
    POSITION
    ES
    C ENTE
    RMENU
    RESE
    T
    HOMEPAGE UP
    PAGE DOWNEND
    VIDEO RGBSEARCH
    FREEZE
    OFF
    ONMAGNIFY
    ASPECT AUTOBLANK
    MUTE
    VOLUME
    KEYSTONE
    POSITION
    ES
    C ENTE
    RMENU
    RESE
    T 
    						
    							
    23
    
    Operating
    Operating the computer screen
    CAUTION  ►Mistaken use of the mouse/keyboard control could damage 
    your equipment. 
    • While using this function, please connect only with a computer. 
    • Before connecting, read the manuals of the computer you will connect. 
    NOTE  • It may not be possible to control notebook PC, and other computers with 
    built-in pointing device (e.g. track ball), using this remote control. In this case, before 
    connecting go into BIOS (system setup) and select external mouse, and disable the 
    pointing device. In addition, the mouse may not function if the computer does not have 
    the needed utility program. See your computer’s hardware manual for details.
    • The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be 
    possible to use the remote control, depending on the computer’s configurations and 
    mouse drivers.
    • The USB control can be used only for the functions listed below. You cannot do things 
    like press two buttons at once (for instance, pressing two buttons at the same time to 
    move the mouse pointer diagonally).
    • This function is not available while the lamp is warming up (the POWER indicator 
    flashes green), and while adjusting the volume and display, correcting for trapezoidal 
    distortion, zooming in on the screen, using the BLANK function, or displaying the menu 
    screen.
    USB mouse and keyboard control
    1. Connect the projector’s USB port to the computer via the mouse cable.
    HOMEPAGE UP
    PAGE DOWNEND
    VIDEO
    RGBSEARCH
    FREEZE
    OFF
    ONMAGNIFY
    ASPECT AUTOBLANK
    MUTE
    VOLUME
    KEYSTONE
    POSITION
    ES
    C ENTE
    RMENU
    RESE
    T
    Available functionRemote control operation
    Move pointerUse ▲, ▼, ◄, ► buttons
    Left click with mousePress ENTER button
    Right click with mouse Press RESET button
    Press keyboard’s HOME key
    Press HOME button
    Press keyboard’s END key
    Press END button
    Press keyboard’s PAGE UP key Press PAGE UP button
    Press keyboard’s PAGE DOWN keyPress PAGE DOWN button
    Press keyboard’s ESC key
    Press ESC button 
    						
    							
    24
    Multifunctional settings
    Multifunctional settings
    Using the menu function
    This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, 
    OPTION, NETWORK and EASY MENU. EASY MENU cosists of functions often used, 
    and the other menus are classified into each purpose. Each of these menus is operated 
    using the same methods. The basic operations of these menus are as follows.
    1. Press the MENU button on the remote control or one of 
    the cursor buttons on the projector.
       
    The Advanced MENU or EASY MENU will appear
    . 
    In the EASY MENU
    2. If you want to change it to the Advanced MENU, select the 
    "Go to Advanced Menu"
    3. Use the cursor buttons ▲/▼ to select an item to operate.
    4. Use the cursor buttons◄/► to operate the item.
    In the Advanced MENU
    2. Use the cursor buttons ▲/▼ to select a menu. 
    If you want to change it to the EASY MENU, select the 
    EASY MENU.
     
    Then press the cursor button ► on the projector or remote 
    control, or the ENTER button on the remote control to select 
    an item. The display of the selected menu will be active.
    3. Use the cursor buttons ▲/▼ to select an item to operate. 
    Then press the cursor button ►  on the projector or remote control,  or the ENTER button 
    on the remote control to progress. The operation menu of the selected item will appear.
    4. Use the cursor buttons▲/▼ to operate the item.
    ● When you want to reset the operation, press the RESET button on the remote control 
    during the operation. Note that items whose functions are performed simultaneously 
    with operation (ex. LANGUAGE, H PHASE, VOLUME etc.) cannot be reset. 
    ● In the advanced menu, when you want to return to the previous display, press the cursor 
    button ◄ on the projector or remote control, or the ESC button on the remote control.
    5. Press the MENU button on the remote control again to close the menu 
    and complete this operation. Even if you don't do anything, the dialog will 
    automatically disappear after about 10 seconds.
    ● Some functions cannot be performed when a certain input port is selected, or 
    when a certain input signal is displayed.
     EASY MENU ASPECT             4:3
    +0
    +0
    +0+0+0 3
     Go To Advance Menu...
    NORMAL
    NORMALNORMAL
       0hENGLISH
    KEYSTONEMODEBRIGHTNESSCONTRASTCOLORTINTSHARPNESSWHISPERMIRRORRESETFILTER TIMELANGUAGE
     MENU [RGB]
     IMAGE SETUP
     PICTURE INPUT
     OPTION SCREEN SHARPNESS        3
     BRIGHTNESS     +0 CONTRAST       +0
     COLOR           +0 TINT            +0 COLOR TEMP   MIDDLE GAMMA        DEFAULT 1
     MY MEMORY    SAVE 1
       :SELECT
     NETWORK EASY MENU PROGRESSIVE  TURN OFF
    RESET button
    ENTER button
    MENU button
    Cursor buttons
    HOMEPAGE UPPAGE DOWNEND
    VIDEO
    RGBSEARCH
    FREEZE
    OFFONMAGNIFYASPECT AUTOBLANK
    MUTEVOLUME
    KEYSTONEPOSITION
    ES
    C ENTERMENU
    RESET
    HOMEPAGE UP
    PAGE DOWNEND
    VIDEO RGBSEARCH
    FREEZE
    OFF
    ONMAGNIFY
    ASPECT AUTOBLANK
    MUTE
    VOLUME
    KEYSTONE
    POSITION
    ES
    C ENTE
    RMENU
    RESE
    T 
    						
    							
    25
    Multifunctional settings
    EASY Menu
    ItemDescription
    ASPECTUsing the buttons ◄/► switches the mode for aspect ratio. 
    See the ASPECT item in the IMAGE menu
     (30).
    KEYSTONE
    Using the buttons ◄/► corrects the keystone distortion.See the item KEYSTONE of section SETUP menu. (21)
    MODE
    Using the buttons ◄/► switches the mode of picture type. The modes of picture type are combinations of a mode of GAMMA and 
    a mode of COLOR TEMP. Choose a suitable mode according to the projected source.
    NORMAL 
      CINEMA  DYNAMIC       
    NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT)
    CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT)
    DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)
    • When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the MODE 
    is “CUSTOM”. Please refer to the GAMMA (27) and COLOR 
    TEMP (28) items in the PICTURE menu.• Wh en this fun ction is performed,  a certain extra such as a line may appear.
    BRIGHTNESSUsing the buttons ◄/► adjusts the brightness.See the item BRIGHTNESS in the PICTURE menu (27).
    CONTRASTUsing the buttons ◄/► adjusts the contrast.See the item CONTRAST of section PICTURE menu (27).
    COLOR Using the buttons ◄/► adjusts the strength of whole color.See the COLOR item in the PICTURE menu (28).
    TINTUsing the buttons ◄/► adjusts the tint.See the 
    TINT item in the PICTURE menu (28).
    SHRPNESS
    Using the buttons ◄/► adjusts the sharpness.See the SHARPNESS item in the PICTURE menu (28).• There may be some noise when an adjustment is made. This is not a malfunction.
    WHISPER Using the buttons ◄/► turns off/on the whisper mode.See the WHISPER item in the SETUP menu (34).
    With the EASY MENU, items shown in the table below can 
    be performed. 
    Select an item using the cursor buttons ▲/▼ on the 
    projector or remote control. Then perform it referring to the 
    following table. 
     EASY MENU ASPECT             4:3
    +0
    +0
    +0+0+0 3
     Go To Advance Menu...
    NORMAL
    NORMALNORMAL
       0hENGLISH
    KEYSTONEMODEBRIGHTNESSCONTRASTCOLORTINTSHARPNESSWHISPERMIRRORRESETFILTER TIMELANGUAGE 
    						
    							
    26
    
    Multifunctional settings
    ItemDescription
    MIRRORUsing the buttons ◄/► switches the mode for mirror status.
    See the MIRROR item in the SETUP menu (34).
    RESETPerforming this item resets all of the items of EASY MENU except 
    FILTER TIME and LANGUAGE. 
    A dialog is displayed for confirmation. Selecting RESET using the 
    button ▲ performs resetting.
    FILTER TIME Performing this item resets the filter timer which counts usage time 
    of the air filter.
    A dialog is displayed for confirmation. Selecting RESET using the 
    button ▲ performs resetting. 
    See the FILTER TIME item in the OPTION menu (38).
    LANGUAGESelect the LANGUAGE item to toggle the menu language. Refer to 
    description of LANGUAGE in the SCREEN menu (35).
    Go To
    Advanced Menu Select “Go To Advanced Menu” to use the menu of PICTURE, 
    IMAGE, INPUT, SETUP, SCREEN or OPTION.
    EASY Menu (continued) 
    						
    							
    27
    
    Multifunctional settings
    PICTURE Menu
    ItemDescription
    BRIGHTNESSUsing the buttons ▲/▼ adjusts the brightness. :    Light  Dark
    CONTRASTUsing the buttons ▲/▼ adjusts the contrast. :    Strong  Weak
    GAMMA
    Using the buttons ▲/▼ switches the GAMMA mode.
    #1 DEFAULT 
      #1 CUSTOM  #2 DEFAULT 
    #3 CUSTOM
      #3 DEFAULT  #2 CUSTOM
    To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM
    Selecting a mode of CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.
    Choose an item using the buttons ◄/►, and  adjust the level using the buttons ▲/▼. 
    Y ou can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as 
    below.
      No pattern  Gray scale of 9 steps 
                     Ramp  Gray scale of 15 steps
    The  eight   equalizing  bars  correspond  to  eight  tone  levels  of  the 
    test  pattern  except  the  darkest  in  the  left  end.  If  you  want  to  adjust 
    the  2nd  tone  from  left  end  on  the  test  pattern,  use  the  equalizing 
    adjustment  bar  “1”.  The  darkest  tone  at  the  left  end  of  the  test 
    pattern cannot be controlled with any of equalizing adjustment bar .
    • When this function is performed, a certain extra such as a line 
    may appear.
    With  the PICTURE   menu,  the  items  shown  in  the  table 
    below can be performed. 
    Select an item using the cursor buttons ▲/▼ on the 
    projector or remote control, and press the cursor button ► 
    on the projector or remote control, or the ENTER button 
    on the remote control to execute the item. Then perform it 
    referring to the following table. 
    1
    +02
    +03
    +04
    +05
    +06
    +07
    +08
    +0
    GAMMA [CUSTOM 1]
    ENTER :
     MENU [RGB]
     IMAGE
     SETUP
     PICTURE
     INPUT
     OPTION SCREEN
     SHARPNESS        3
     BRIGHTNESS     +0 CONTRAST       +0
     COLOR           +0 TINT            +0
     COLOR TEMP   MIDDLE GAMMA        DEFAULT 1
     MY MEMORY    SAVE 1
       :SELECT
     NETWORK EASY MENU PROGRESSIVE  TURN OFF 
    						
    							
    28
    
    Multifunctional settings
    ItemDescription
    COLOR TEMP
    Using the buttons ▲/▼ switches the mode of color temperature.
    HIGH  MIDDLE  LOW  CUSTOM     
    To adjust CUSTOM
    Selecting the CUSTOM and then pressing the button ► or the ENTER button displays a dialog 
    to aid you in adjusting the OFFSET and/or GAIN 
    of the CUSTOM mode.
    OFFSET adjustments change the color intensity 
    on the whole tones of the test pattern.
    GAIN adjustments mainly affect color intensity 
    on the brighter tones of the test pattern.
    Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼. 
    You can display a test pattern for checking the effect of your 
    adjustment by pressing the ENTER button.  Each time you press the ENTER button, the pattern changes as 
    below.
      No pattern  Gray scale of 9 steps 
                     Ramp  Gray scale of 15 steps
    • When this function is performed, a certain extra such as a line 
    may appear.
    COLOR
    Using the buttons ▲/▼ adjusts the strength of whole color.
    Strong   Weak
    • This item can be selected only for a video signal.
    TINT
    Using the buttons ▲/▼ adjusts the tint.
    Green  Red
    • This item can be selected only for a video signal except for SECAM.
    SHARPNESS
    Using the buttons ▲/▼ adjusts the sharpness.
    Strong  Weak• 
    There may be some noise and/or the screen may flicker for a 
    moment when an adjustment is made. This is not a malfunction.
    PICTURE Menu (continued)
    R
    +0
    G
    +0
    B
    +0COLOR TEMP
    ENTER :OFFSETR
    +0
    G
    +0
    B
    +0
    GAIN 
    						
    							
    29
    
    Multifunctional settings
    ItemDescription
    PROGRESSIVE
    Using the buttons ▲/▼ switches the progress mode.
    TV  FILM  TURN OFF
    • This function is performed only for an interlaced signal of a VIDEO 
    input, an S-VIDEO input or CONPONENT VODEO input of 525i 
    (480i) or 625i (576i) signal.
    • When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture 
    for a quick moving object. In such a case, please select TURN OFF, 
    even though the screen image may lose the sharpness.
    MY MEMORY Selecting a mode of MY MEMORY using the buttons ▲/▼ and then 
    pressing the button ► or the ENTER button performs each function.
    LOAD1  LOAD2  LOAD3  LOAD4
    SAVE4 
     SAVE3  SAVE2  SAVE1
    This projector has 4 numbered memories for adjustment data.  Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds to the c
    ommand’s number, and adjusts the picture automatically depending on the data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 saves the current adjustment data on the memory whose number corresponds to the 
    command’s number. 
    • The current adjustment data of the items in the PICTURE menu is 
    stored, except for the adjustment data in the CUSTOM modes for 
    the GAMMA and COLOR TEMP items.
    •  There may be some noise and/or the screen may flicker for a 
    moment when data is loaded to memory. This is not a malfunction.
    PICTURE Menu (continued) 
    						
    							
    30
    
    Multifunctional settings
    IMAGE Menu
    ItemDescription
    ASPECT
    Using the buttons ▲/▼ switches the mode for aspect ratio. 
    For an RGB signal4:3  16:9  NORMAL   
    For a video signal / no signal4:3  16:9  SMALL    
    • The NORMAL mode keeps the original aspect ratio of the signal.• For an HDTV signal of 1125i (1080i) or 750p (720p) as the 
    COMPONENT VIDEO input, this item can't be selected. 
    OVER SCAN
    Using the buttons ▲/▼ adjusts the over-scan ratio.
    Large (It reduces picture)   Small (It magnifies picture)
    • This item can be selected only for a video signal.
    •  When this adjustment is too large, certain degradation may appear 
    at the frame area of the picture. In such a case, please adjust small.
    V POSITION
    Using the buttons ▲/▼ adjusts the vertical position.
    Up  Down• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs please reset the vertical position to the 
    default setting. Pressing the RESET button when V POSITION is 
    selected will reset the V POSITION to the default setting.
    H POSITION
    Using the buttons ▲/▼ adjusts the horizontal position.
    Left  Right• Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to 
    the default setting. Pressing the RESET button when H POSITION 
    is selected will reset the H POSITION to the default setting.
    H PHASE
    Using the buttons ▲/▼ adjusts the horizontal phase to eliminate 
    flicker.
    Right  Left
    • This item can be selected only for an RGB signal or a component video signal. Note that this does not work with the input signal of 
    525i(480i)/625i(576i)/SCART RGB from the component video port.
    With the IMAGE menu, items shown in the table below can 
    be performed. 
    Select an item using the cursor buttons ▲/▼ on the 
    projector or remote control, and press the cursor button ► 
    on the projector or remote control, or the ENTER button 
    on the remote control to execute the item. Then perform it 
    referring to the following table. 
     MENU [RGB]
     IMAGE PICTURE
       :SELECT
     AUTO ADJUST EXECUTE
     ASPECT         4:3 OVER SCAN      5
     H PHASE        16 H SIZE         1344
     H POSITION     142 V POSITION     25 SETUP INPUT
     OPTION NETWORK EASY MENU
     SCREEN 
    						
    All InFocus manuals Comments (0)

    Related Manuals for InFocus Projector CP-S245 CP-X255 User Manual