InFocus LP1200 Projector User Manual

21
ENGLISH
U OPTION
MOTION/STILL . Select MOTION when motion images are mainly projected.  Select STILL when still images
such as PC-CARD images are mainly projected.  It works only when inputting personal
computers of SXGA signals or inputting video signal.
SQUEEZE ........... Set to switch the normal image (4:3) and HDTV (16:9) automatically or not, depending on the
image signals.
MENU POSITION .Use to select the position where the menu is displayed (top or bottom on the screen).
AUTO POWER OFF ..Use...

22
ENGLISH
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers.  In this case, press AUTO POSITION
button.  If the images are still not projected correctly,
use MENU display to adjust the projected images
from personal computers.  Also available to memorize
the setting.
Adjusting the images form personal
computers in MENU display
Adjust as below for the following...

23
ENGLISH
Specification of RGB signals in each computer mode of the projector
Signal mode resolution horizontal Vertical Normal Native (H x V) frequency (kHz) frequency (Hz) (H x V)  (H x V)
TV60 Ð 15.73 59.94 1024 x 768 (640 x 480)
TV50 Ð 15.63 50.00 1024 x 768 (640 x 480)
HiVision Ð 33.75 60.00 1024 x 576 (882 x 496)
PC98 640 x 400 24.82 56.42 1024 x 640 640 x 400
CGA70 640 x 400 31.47 70.09 1024 x 640 640 x 400
CGA84 640 x 400 37.86 84.13 1024 x 640 640 x 400
CGA85 640 x 400 37.86 85.08 1024 x 640...

24
ENGLISH
GAMMA CORRECTION menu
The proportion of the brightness of input signals to that of output signals can be corrected effectively by adjusting
GAMMA.
1. Select  GAMMA CORRECTION of PICTURE menu
and then press the ENTER button. (The GAMMA
CORRECTION menu appears on-screen display.)
Horizontal axis: brightness of the input signals
Vertical axis: brightness of the output signals
Inclination: GAMMA
2. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select...

25
ENGLISH
Advanced feature for presentation
Cursor operation
1. Press the CURSOR button.
The cursor appears on the screen.
2. Press the START/STOP button to ON.
The operation indicator will be illuminated.
(The operation indicator will turn off if the remote
control is not used for a period of five minutes.)
3. Move the cursor by using the remote control.
4. Press the START/STOP button to momentarily
freeze the cursor movement. Press again to resume
moving.
5. Press the CURSOR button to cause the cursor...

26
ENGLISH
Advanced feature for presentation (Continue)
Expand
By pressing the EXPAND button on the remote con-
trol, you can view the detailed image of the picture.
Setting the Expand mode
1. Press the MENU button once to display the on-
screen menu.
2. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
PinP/EXPAND.
3. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control).
4. Press the
 or buttons on the control panel (or
$ or...

27
ENGLISH
PC-CARD
The projector can play back an image by using the PC-
CARD.
Using the PC-CARD
Use only the flash memory card of PCMCIA¥ATA com-
patible type II.
¥ Due to PC-CARD type, some images can not be prop-
erly recorded.  Please contact your dealer.
Setting up the PC-CARD
1. Set the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
2. Open PC-CARD cover on the left side of the projec-
tor.
3. Make sure the PC card is going to be inserted in
right...

28
ENGLISH
PC-CARD (Continue)
To automatically change the image, follow the steps
as shown below.
1. Press the MENU button.
2. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select PC
CARD AUTO  PLAY.
3. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control).
4. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
AUTO SLIDE TIME.
5. Press the » or ¼ buttons on the control panel (or
{ or }...

29
ENGLISH
Advanced feature with PC
There are three types of application software provided.
1. PCV (PC Card Viewer)
2. PCGC (Personal Computer Graphic Controller)
3. SpacePointer (Driver for PC control by the remote
controller)
Environment
The following system software and hardware are nec-
essary to use the projector.
When you use Macintosh
¥ Macintosh series loading more than 68030 in
CPU and a video card with which more than
256 colors are available
¥ System7.1 or newer
¥ 8MB of Random-access memory...

30
ENGLISH
Advanced feature with PC (Continue)
Starting up PCV (For Windows)
For Windows 95 or Windows NT
1. Start up Windows.
2. Insert the PC card to the PC Card slot on the per-
sonal computer.
3. Start up Program Manager.
Click the [Start] button and select the [Program
(
P)]Ô[Pcv]Ô[PCV]command.
For Windows 3.1
1. Start up Windows.
2. Insert the PC card to the PC Card slot on the per-
sonal computer.
3. Double click the [PCV] icon in the PCV folder.
Command reference (For Windows 95 or
Windows NT)...