InFocus LP1200 Projector User Manual

11
ENGLISH
Adjusting the angle of projection
Screen on a flat wall with a 90 degree angle to the floor
by adjusting two foot adjustments on the bottom of the
projector.  If the angle cannot be corrected by them,
adjust the height and angle of screen.
1. Lift the projector to the right angle.
2. Press the release button for angle adjustment to take
the adjustment feet out of the projector.
3. Release the button and keep your hands away from
the projector.
4. Turn the both feet to right or left to adjust...

12
ENGLISH
Basic connections
The projector can be connected to equipment such as VCRs, video cameras, videodisc players, and personal comput-
ers having analog RGB input.
Important:
¥ Make sure that your equipment is turned off before connection.
¥ Match the color of video and audio plugs on the AV cable with each terminal.
¥ Plug in firmly and unplug by holding the plug, not by pulling the cable out.
¥ If connected units are set too close to one another, the image may be affected. Setting connected...

13
ENGLISH
Projector + IBM PC or IBM PC compatibles
Make sure that your equipment is turned off before connection.
Important:
¥ Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to
this projector.  Please contact your dealer.
¥ The audio input for a personal computer is the stereo mini-jack. There are some personal computers that have
different types of audio outputs or none at all. Please ask your dealer for details.
¥ For connection details, refer to...

14
ENGLISH
Projector + Macintosh
Make sure that your equipment is turned off before connection.
Important:
¥ A monitor output adapter is necessary for a Macintosh if it has no video port. Contact your dealer.
¥ If you use the RGB conversion adapter provided, set the dip switch to the appropriate position. See page 12.
¥ Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to
this projector.  Please contact your dealer.
¥ The audio input for a personal...

15
ENGLISH
Projector + NEC PC-98 series
Make sure that your equipment is turned off before connection.
Important:
¥ Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to
this projector.  Please contact your dealer.
¥ The audio input for a personal computer is the stereo mini jack. There are some personal computers that have
different type or no audio outputs. Please ask your dealer for details.
¥ For connection details, refer to the owners guide of each...

16
ENGLISH
To operate projector power ON
Numbers 1 - 9 correspond to the instruction numbers below.
Important:
¥ A darkened image may be seen right after pressing
the POWER button  due to warming up of this pro-
jector. When warming up, no other commands can
be accepted.
¥ When the lamp indicator is blinking red, the ser-
vice life of the lamp is about to end.  Replace the
lamp. See pages 40 and 44.
¥ The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not...

17
ENGLISH
AUTO POSITION button
When the source is selected to RGB1 or RGB2 and
the image is not in the right place, set to display as
blightest signal as possible, then press the AUTO
POSITION button. If the image is still not in the
right place.
¥ Set screen to the brightest display possible (e.g.,
full-screen display of the ÒTrashÓ window) before
deploying the automatic adjustment function.
¥ If the screen saver is running, turn off the screen
saver before using the automatic adjustment
button.
5....

18
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Brightness adjustment
1.  Press the MENU button.
2.  Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
PICTURE.
3.  Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control).
4.  Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
BRIGHTNESS.
5.  Press the » or ¼ buttons on the control panel (or
{ or }...

19
ENGLISH
Q SIGNAL
AUTO .................. Use to select AUTO, USER 1 or USER 2.
HORIZ. POSITION ....Use to adjust the horizontal position of the image.
VERT. POSITION .....Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
RGB/Y, CB, CR ...The unit adjusts itself automatically when connected to either DVD players with a
component...

20
ENGLISH
E PinP/EXPAND
This menu appears when either the display enlargement or PinP functions are used.
ZOOM MODE ..... Selects the desired type of expand mode, type1, 2, 3 or 4 (actual size display).
POSITION .......... Selects the desired position of the sub image in expand or PinP mode.
SIZE .................... Selects the desired size of the sub image in expand or PinP mode.
AUTO PIP ........... Sets to move the position of PinP pictures automatically or not, when it appears on the red
frame...