Indesit Pwse 6108 W Instructions For Use

							1
GB
English, 1
GB
WASHING MACHINE
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine, 4-5
Control panel
Display
Running a wash cycle, 6
Wash cycles and options, 7
Table of programmes and wash cycles
Wash options
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Precautions and advice, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
PWSE 6108 S
Instructions for use
CIS
Русский,13
   
						

							2
GB
Installation
! This instruction manual should be kept in a safe place for 
future reference. If the washing machine is sold, transferred 
or moved, make sure that the instruction manual remains 
with the machine so that the new owner is able to 
familiarise himself/herself with its operation and features.
! Read these instructions carefully: they contain vital 
information relating to the safe installation and operation of 
the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been 
damaged during the transportation process. If it has been 
damaged, contact the retailer and do not proceed any 
further with the installation process.
3. Remove the 4 protective 
screws (used during 
transportation) and the 
rubber washer with the 
corresponding spacer, 
located on the rear part of 
the appliance (see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them 
again if the washing machine needs to be moved to 
another location.
! Packaging materials should not be used as toys for 
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without 
resting it up against walls, furniture cabinets or anything 
else.
2. If the floor is not perfectly 
level, compensate for any 
unevenness by tightening or 
loosening the adjustable front 
feet (see figure); the angle 
of inclination, measured in 
relation to the worktop, must 
not exceed 2°.
Levelling the machine correctly will provide it with stability, 
help to avoid vibrations and excessive noise and prevent it 
from shifting while it is operating. If it is placed on carpet or 
a rug, adjust the feet in such a way as to allow a sufficient 
ventilation space underneath the washing machine.
Connecting the electricity and water 
supplies
Connecting the water inlet hose
1. Connect the inlet hose 
by screwing it to a cold 
water tab using a 3/4 gas 
threaded connection (see 
figure).
Before performing the 
connection, allow the 
water to run freely until it is 
perfectly clear.
2. Connect the inlet hose 
to the washing machine 
by screwing it onto the 
corresponding water inlet 
of the appliance, which is 
situated on the top right-
hand side of the rear part of 
the appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the range of 
values indicated in the Technical data table (see next page).
! If the inlet hose is not long enough, contact a specialised 
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
    
						

							3
GBConnecting the drain hose
Connect the drain hose, 
without bending it, to a 
drain duct or a wall drain 
situated between 65 and 
100 cm from the floor;
alternatively, place it over 
the edge of a basin, sink 
or tub, fastening the duct 
supplied to the tap (see 
figure). The free end of 
the hose should not be 
underwater.
! We advise against the use of hose extensions; if it is 
absolutely necessary, the extension must have the same 
diameter as the original hose and must not exceed 150 cm 
in length.
Electrical connections
Before plugging the appliance into the electricity socket, 
make sure that: 
•	 the	socket	is	earthed	and	complies	with	all	applicable	
laws;
•	 the	socket	is	able	to	withstand	the	maximum	power	
load of the appliance as indicated in the Technical data 
table (see opposite);
•	 the	power	supply	voltage	falls	within	the	values	
indicated in the Technical data table (see opposite);
•	 the	socket	is	compatible	with	the	plug	of	the	washing	
machine. If this is not the case, replace the socket or the 
plug.
! The washing machine must not be installed outdoors, 
even in covered areas. It is extremely dangerous to leave 
the appliance exposed to rain, storms and other weather 
conditions.
! When the washing machine has been installed, the 
electricity socket must remain within easy reach. 
! Do not use extension cords or multiple sockets.
65 - 100 cm
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by 
authorised technicians.
Warning! The company shall not be held responsible in the 
event that these standards are not observed.
The first wash cycle
Once the appliance has been installed, and before you use 
it for the first time, run a wash cycle with detergent and no 
laundry, using wash cycle number 2.
Technical data
Model
PWSE 6108 S
Dimensions width 59.5 cm
height 85 cm
depth 44,5 cm
Capacity from 1 to 6 kg 
Electrical 
connections please refer to the technical data plate 
fixed to the machine
Water connections maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 40 litres
Spin speed up to 1000 rotations per minute
Energy rated 
programmes 
according to 
regulation 
EN 60456 programme 2; temperature 60°C;
using a load of 6 kg.
This appliance conforms to the following 
EC Directives:
- 89/336/EEC dated 03/05/89 (Electro-
magnetic Compatibility) and subsequent 
modifications
- 2006/95/EC (Low Voltage)
- 2002/96/EC
   
						

							4
GB
Description of the washing 
machine
Control panel
TEMPERATURE button
WASH CYCLE SELECTOR KNOB
Detergent dispenser drawer
ON/OFF button
SPIN button START/PAUSE button and indicator light
DISPLAY
DELAYED 
START button
OPTION buttons and indicator lightsDOOR 
LOCKED indicator light
Detergent dispenser drawer: used to dispense 
detergents and washing additives ( see “Detergents and 
laundry”).
ON/OFF  button: press this briefly to switch the 
machine on or off. The START/PAUSE indicator light which 
flashes slowly in a blue colour shows that the machine is 
switched on. To switch off the washing machine during the 
wash cycle, press and hold the button for approximately 3 
seconds; if the button is pressed briefly or accidentally the 
machine will not switch off.
If the machine is switched off during a wash cycle, this 
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the 
desired wash cycle (see “Table of programmes and wash 
cycles”).
OPTION buttons and indicator lights: press to select the 
available options. The indicator light corresponding to the 
selected option will remain lit.
SPIN  button: press to reduce or completely exclude 
the spin cycle; the value appears on the display.
TEMPERATURE   button: press to reduce or 
completely exclude the temperature; the value appears on 
the display.
DELAYED START  button: press to set a delayed start 
for the selected wash cycle; the delay period appears on 
the display. 
START/PAUSE  button and indicator light: when the 
blue indicator light flashes slowly, press the button to start 
a wash cycle. Once the cycle has begun the indicator light 
will remain lit in a fixed manner. To pause the wash cycle, 
press the button again; the indicator light will flash in an 
amber colour. If the  symbol is not illuminated, the door 
may be opened. To start the wash cycle from the point at 
which it was interrupted, press the button again.
DOOR LOCKED  indicator light:
The lit symbol indicates that the door is locked. To prevent 
any damage, wait until the symbol turns off before opening 
the door.
To open the door while a cycle is in progress, press the 
START/PAUSE button; if the DOOR LOCKED  symbol is 
switched off the door may be opened.
Standby mode
This washing machine, in compliance with new energy 
saving regulations, is fitted with an automatic standby 
system which is enabled after a few minutes if no activity is 
detected. Press the ON-OFF button briefly and wait for the 
machine to start up again.
 
						

							5
GBDisplay
B
C
A
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED 
START option has been set, the countdown to the start of the selected wash c\
ycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperatu\
re values attained by the 
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The hour-glass flashes while the machine is processing data, depending on the wash cycle and Smart level selected. 
After a maximum of 10 minutes, the “hour-glass” icon remains lit in a fixed manner and the final amount of time remaining 
is displayed. The hour-glass icon will then switch off approximately 1 minute after the final amount of time remaining has 
appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of\
 the running wash cycle 
appear in section B:
 Main wash
 Rinse
 Spin
 Drain
The icons corresponding to “temperature”, “spin” and “delayed start” (working from the left) are displayed in section C.
The “temperature” bars  indicate the maximum temperature level which may be selected for the set cycle.
The “spin” bars  indicate the maximum spin level which may be selected for the set cycle\
.
The “delay” symbol , when lit, indicates that the set “delayed start” value has appea\
red on the display.
 
						

							6
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the  button; 
the START/PAUSE indicator light will flash slowly in a 
blue colour.
2. LOAD THE LAUNDRY.  Open the porthole door. 
Load the laundry, making sure you do not exceed 
the maximum load value indicated in the table of 
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the 
detergent dispenser drawer and pour the detergent into 
the relevant compartments as described in “Detergents 
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE 
SELECTOR knob to select the desired wash cycle. A 
temperature and spin speed is set for each wash cycle; 
these values may be adjusted. The duration of the cycle 
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant 
buttons:
   Modify the temperature and/or spin 
speed. The machine automatically displays the 
maximum temperature and spin speed values set for 
the selected cycle, or the most recently-used settings 
if they are compatible with the selected cycle. The 
temperature can be decreased by pressing the  
button, until the cold wash “OFF” setting is reached. 
The spin speed may be progressively reduced by 
pressing the  button, until it is completely excluded 
(the “OFF” setting). If these buttons are pressed again, 
the maximum values are restored.
 Setting a delayed start.
To set a delayed start for the selected cycle, press the 
corresponding button repeatedly until the required delay 
period has been reached. When this option has been 
activated, the  symbol lights up on the display. To 
remove the delayed start setting, press the button until 
the text “OFF” appears on the display.
    Modify the cycle settings.
•	 Press	the	button	to	enable	the	option;	the	indicator	
light corresponding to the button will switch on.
•	 Press	the	button	again	to	disable	the	option;	the	
indicator light will switch off.
! If the selected option is not compatible with the set 
wash cycle, the indicator light will flash and the option 
will not be activated.
! If the selected option is not compatible with 
a previously selected one, the indicator light 
corresponding to the first function selected will flash and 
only the second option will be activated; the indicator 
light for the option which has been activated will be 
illuminated.
Note: if the SMART option has been selected, none of 
the incompatible options may be activated.
! The options may affect the recommended load value 
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will 
turn blue, remaining lit in a fixed manner, and the door 
will be locked (the DOOR LOCKED  symbol will be lit). 
To change a wash cycle while it is in progress, pause 
the washing machine using the START/PAUSE button 
(the START/PAUSE indicator light will flash slowly in an 
amber colour); then select the desired cycle and press 
the START/PAUSE button again.
To open the door while a cycle is in progress, press the 
START/PAUSE button; if the DOOR LOCKED  symbol 
is switched off the door may be opened. Press the 
START/PAUSE button again to restart the wash cycle 
from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be 
indicated by the text “END” on the display; when the 
DOOR LOCKED  symbol switches off the door may be 
opened. Open the door, unload the laundry and switch 
off the machine.
! If you wish to cancel a cycle which has already begun, 
press and hold the  button. The cycle will be stopped 
and the machine will switch off.
Load balancing system
Before every spin cycle, to avoid excessive vibrations 
before every spin and to distribute the load in a uniform 
manner, the drum rotates continuously at a speed which 
is slightly greater than the washing rotation speed. If, 
after several attempts, the load is not balanced correctly, 
the machine spins at a reduced spin speed. If the load is 
excessively unbalanced, the washing machine performs 
the distribution process instead of spinning. To encourage 
improved load distribution and balance, we recommend 
small and large garments are mixed in the load.
 
						

							7
GB
Wash cycles and options
Wash options
The  option optimises washing to suit the quantity 
of laundry loaded into the machine, thereby reducing the 
overall wash cycle duration while minimising water and energy 
consumption. Press the  button to select the type of 
wash cycle desired:
Intensive: vigorous wash cycle for garments with a heavy soil 
level.
4 You: standard wash cycle for garments with a normal soil level.
Fast: quick wash cycle for garments with a light soil level.
! This may only be used in conjunction with wash cycles 1, 2, 
3, 4, 5, 6 (all three levels) and 7, 8, 9 (4 You and Fast levels).
 Extra Rinse
By selecting this option, the efficiency of the rinse is increased 
and optimal detergent removal is guaranteed. It is particularly 
useful for sensitive skin.
! It cannot be used in conjunction with wash cycles 9, , .
 Easy iron
By selecting this function, the wash and spin cycles will be 
modified in order to reduce the formation of creases. At the end 
of the cycle the washing machine will perform slow rotations of 
the drum, while the EASY IRON and START/PAUSE indicator 
lights will flash (blue and orange respectively). To end the cycle, 
press the START/PAUSE button or the EASY IRON button. 
For wash cycles number 11-13, the machine will end the 
cycle while the laundry is soaking; the EASY IRON and 
START/PAUSE indicator lights will flash. 
To drain the water so that the laundry may be removed, 
press the START/PAUSE button or the EASY IRON button.
! It cannot be used in conjunction with wash cycles 9, 10, 
12, , . 
 Stain removal
This function is particularly 
useful for the removal of 
stubborn stains. Insert extra 
compartment 4 (supplied 
with the appliance) into 
compartment 1. When pouring 
in the bleach, be careful not to 
exceed the “max” level marked 
on the central pivot (see figure). 
To bleach laundry with no 
other washing action, pour the 
bleach into extra compartment 4, select the “Rinse” cycle  
and activate the “Stain removal” option . To bleach during 
a wash cycle, pour in the detergent and any fabric softener 
you wish to use, select the desired wash cycle and enable the 
“Stain removal”  option. The use of extra compartment 4 
excludes the pre-wash function.
! It cannot be used in conjunction with wash cycles 1, 7, 9, 
10, 11, 12, 13, , . 
For all Test Institutes: 1) Test wash cycle in compliance with regulation EN 60456: select wash cycle 2 with a temperature of 60°C. 2) Long wash cycle for cottons: select wash cycle 2 with a temperature of 40. 3) Short wash cycle for cottons: select wash cycle 4 with a temperature of 40.
Table of programmes and wash cycles
42
3
14
2
1
3
Wash cycles
Description of the wash cycle Max. 
temp.  (°C) Max. 
speed  (rpm) Detergents
Max. 
load (kg) Cycle 
duration
Pre-wash Main wash BleachFabric
softener
Smart cycles
The duration of the wash cycles can be checked on the display.
1 Cottons with Pre-wash: extremely soiled whites. 90°1000 

-
6
2 White Cottons:  extremely soiled whites. 90°1000 -

6
2 White Cottons (1):  heavily soiled whites and resistant colours. 60°1000 -

6
2 White Cottons (2):  heavily soiled whites and delicate colours. 40°1000 -

6
3 Cottons:  heavily soiled whites and resistant colours. 60°1000 -

6
4 Coloured Cottons(3):  lightly soiled whites and delicate colours. 40°1000 -

6
5 Synthetics: heavily soiled resistant colours. 60°800 - 

2,5
6 Synthetics: lightly soiled resistant colours. 40°800 - 

2,5
7 Jeans
40°800 - 
-
2,5
8 Shirts
40°600 - 

2
9 Mix-Cool 30’: to refresh lightly soiled garments quickly (not sui-
table for wool, silk and clothes which require washing by hand). Cold 
water 800
- 
-
3
Special cycles
10 Wool:  for wool, cashmere, etc. 40°600 - 
-
1,5
11 Silk/Curtains: for garments in silk and viscose, lingerie. 30°0 - 
-
1
12 Sport Shoes
30°600 - 
-Max.2 
paires
13 Outwear
30°400 - 
--1,5
Partial cycles
Rinse -1000 - -

6
Spin -1000 - --- 6
Drain -0 - --- 6
 
						

							8
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct 
dose of detergent: adding too much detergent will not 
necessarily result in a more efficient wash, and may in 
fact cause build up on the inside of your appliance and 
contribute to environmental pollution.
! Do not use hand washing detergents; they create too 
much foam.
Open the detergent 
dispenser drawer and pour 
in the detergent or washing 
additive, as follows.
Compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra 
compartment 4 has been removed.
Compartment 2: Washing detergent (powder or 
liquid)
Liquid detergent should only be poured in immediately 
prior to the start of the wash cycle.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid. 
extra compartment 4: Bleach
Preparing the laundry
•	 Divide	the	laundry	according	to:
 - the type of fabric/the symbol on the label
 - the colours: separate coloured garments from whites.
•	 Empty	all	garment	pockets	and	check	the	buttons.
•	 Do	not	exceed	the	listed	values,	which	refer	to	the	
weight of the laundry when dry:
 Durable fabrics: max. 6 kg
 Synthetic fabrics: max. 2,5 kg
 Delicate fabrics: max. 2 kg
 Wool: max. 1,5 kg
 Silk: max. 1 kg
How much does your laundry weigh?
 1 sheet 400-500 g
 1 pillow case 150-200 g
 1 tablecloth 400-500 g
 1 bathrobe 900-1.200 g
 1 towel 150-250 g
Special wash cycles
Jeans: turn the garments inside out before washing and 
use liquid detergent. Use wash cycle 7.
4
2
3
14
2
1
3
Shirts: use special wash cycle 8 to wash shirts in various 
fabrics and colours.
It guarantees maximum care is taken of the garments and 
minimises the formation of creases.
Mix-Cool 30’: this wash cycle was designed to wash 
lightly soiled garments quickly: it lasts just 30 minutes 
and therefore saves both energy and time. By selecting 
wash cycle 9, it is possible to wash different fabrics 
(except for wool and silk items) using a cold cycle, up to 
a maximum load of 3 kg.
Wool: wash cycle 10 can be used to wash all woollen 
garments in the machine, even those carrying the “hand 
wash only”  label. To achieve the best results, use a 
special detergent and do not exceed the maximum load of 
1,5 kg.
Silk: use special wash cycle 11 to wash all silk garments. 
We recommend the use of special detergent which has 
been designed to wash delicate clothes.
Curtains: we recommend you fold the curtains and place 
them in a pillow case or mesh bag. Use wash cycle 11.
Sport Shoes (wash cycle 12): is for washing sports 
shoes; for best results, do not wash more than 2 pairs 
simultaneously. 
Outwear (wash cycle 13): is studied for washing water-
repellent fabrics and winter jackets (e.g. Gore-Tex, 
polyester, nylon); for best results, use a liquid detergent 
and dosage suitable for a half-load; pre-treat necks, 
cuffs and stains if necessary; do not use softeners or 
detergents containing softeners. Stuffed duvets cannot 
be washed with this programme.
    
						

							9
GB
Precautions and tips
Opening the porthole door manually
In the event that it is not possible to open the porthole door 
due to a powercut, and if you wish to remove the laundry, 
proceed as follows:
1. Remove the plug from the 
electrical socket..
2. Make sure the water level 
inside the machine is lower 
than the door opening; if 
it is not, remove excess 
water using the drain hose, 
collecting it in a bucket as 
indicated in the figure.
3. Remove the cover panel on the lower front part of the 
washing machine (see overleaf).
4. Pull outwards using the tab as indicated in the figure, 
until the plastic tie-rod is freed from its stop position; pull 
downwards and open the door at the same time.
5. Reposition the panel, making sure the hooks are 
securely in place before you push it onto the appliance.
! This washing machine was designed and constructed 
in accordance with international safety regulations. The 
following information is provided for safety reasons and 
must therefore be read carefully.
General safety
•	 This	appliance	was	designed	for	domestic	use	only.
•	 The	washing 	machine 	must 	only 	be 	used 	by 	adults, 	in	
accordance with the instructions provided in this manual.
•	 Do	not	touch	the	machine	when	barefoot	or	with	wet	or	
damp hands or feet.
•	 Do	not	pull	on	the	power	supply	cable	when	unplugging	
the appliance from the electricity socket. Hold the plug 
and pull. 
•	 Do	not	open	the	detergent	dispenser	drawer	while	the	
machine is in operation.
•	 Do	not	touch	the	drained	water	as	it	may	reach	
extremely high temperatures.
•	 Never	force	the	porthole	door.	This	could	damage	the	
safety lock mechanism designed to prevent accidental 
opening.
•	 If	the	appliance	breaks	down,	do	not	under	any	
circumstances access the internal mechanisms in an 
attempt to repair it yourself.
•	 Always	keep	children	well	away	from	the	appliance	while	
it is operating.
•	 The 	door 	can 	become 	quite 	hot 	during 	the 	wash 	cycle.
•	 If	the	appliance	has	to	be	moved,	work	in	a	group	of	two	
or three people and handle it with the utmost care. Never 
try to do this alone, because the appliance is very heavy.
•	 Before	loading	laundry	into	the	washing	machine,	make	
sure the drum is empty.
Disposal
•	Disposing	of	the	packaging	materials:
  observe local regulations so that the packaging may be 
re-used.
•	The	European	Directive	2002/96/EC	relating	to	Waste	
Electrical and Electronic Equipment (WEEE) states 
that household appliances should not be disposed of 
using the normal solid urban waste cycle. Exhausted 
appliances should be collected separately in order to 
optimise the cost of re-using and recycling the materials 
inside the machine, while preventing potential damage 
to the atmosphere and to public health. The crossed-out 
dustbin is marked on all products to remind the owner of 
their obligations regarding separated waste collection.
 For more information relating to the correct disposal of 
household appliances, owners should contact their local 
authorities or appliance dealer.
   
						

							10
GB
Care and maintenance 
Cutting off the water and electricity 
supplies
•	 Turn	off	the	water	tap	after	every	wash	cycle.	This	will	
limit wear on the hydraulic system inside the washing 
machine and help to prevent leaks.
•	 Unplug	the	washing	machine	when	cleaning	it	and	
during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance 
can be cleaned using a soft cloth soaked in lukewarm 
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser 
drawer
To remove the drawer, press 
lever (1) and pull the drawer 
outwards (2) (see figure).
Wash it under running water; 
this procedure should be 
repeated frequently.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump 
which does not require any maintenance. Sometimes, 
small items (such as coins or buttons) may fall into the 
protective pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and unplug the 
appliance.
To access the pre-chamber:
1. Take off the cover panel 
on the front of the machine 
by first pressing it in the 
centre and then pushing 
downwards on both sides 
until you can remove it (see 
figures).
2
1
1
23
2. Unscrew the lid by 
rotating it anti-clockwise 
(see figure): a little water 
may trickle out. This is 
perfectly normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks are 
securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any 
cracks, it should be replaced immediately: during the wash 
cycles, water pressure is very strong and a cracked hose 
could easily split open.
! Never use second-hand hoses.