Iiyama Prolite T1730sr User Manual

							ENGLISH
COMPUTER SETTING
„Signal Timing
Change to the desired signal timings listed on page 21 in COMPLIANT TIMING.
„Windows 95/98/2000/Me/XP/Vista Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on
Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with
the Signal Cable supplied. Windows 95/98/2000/Me/XP Monitor Information File for iiyama monitors
may be necessary for your computer and obtained via the Internet, using the address:
http://www.iiyama.com
„For additional information on how to download the driver for your monitor, please
access one of the internet sites noted above.
„Monitor Drivers are not required in most cases for Macintosh or Unix operating systems.
For further information, please contact your computer dealer first for advice.
„Procedure for turning ON the Power Switch
Turn ON the monitor first, and then the computer.
„Touch screen driver software
Touch screen driver software and system may not start when you start your computer while
touching the screen.
Touch screen driver software may not run due to the power saving function depending on the
BIOS of your computer. In this case, set the power saving function to off.NOTE
ADJUSTING THE VIEWING ANGLE
„For optimal viewing it is recommended to look at the
full face of the monitor, then adjust the monitor’s angle
to your own preference.
„Hold the panel so that the monitor does not topple
when you change the monitor’s angle.
„You are able to adjust the monitor’s angle up to 90
degrees upward, 5 degrees downward.
NOTE„Do not touch the LCD screen when you
change the angle. It may cause damage
or break the LCD screen.
„Careful attention is required not to catch
your fingers or hands when you change
the angle.
90˚
5˚
BEFORE YOU OPERATE THE MONITOR     8
 
						

							ENGLISH
9     OPERATING THE MONITOR
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 21. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 13 for SCREEN ADJUSTMENTS.
( (( (
(Press the Menu Button to start the On Screen Display feature. There are
additional menu pages which can be switched by using the 
/ Buttons.
NOTEUse the +/– Buttons to change the vertical position settings. The vertical position of the overall
display should be changing accordingly while you are doing this.
B BB B
BUse the +/– Buttons to make the appropriate adjustment or setting.
Adjustments for Clock, Phase and Position are saved for each signal timing. Except for these
adjustments, all other adjustments have only one setting which applies to all signal timings. „For example, to correct for vertical position, press the Menu Button. Then, select       (V-
POSITION) by using the 
/ Buttons.
Any changes are automatically saved in the memory when the On Screen Display 
disappears.
Turning off the power should be avoided while using the Menu.„
1280x1024
Adjustment icon
Menu page ANALOG
EXIT SELECT
Page
Page
CONTRAST
BRIGHTNESS 
VOLUME 
AUTO TUNE 
H-POSITION 
V-POSITION 
LANGUAGE
EXIT
1280x1024
ANALOG
EXIT SELECT
Page
Page
CONTRAST
BRIGHTNESS 
VOLUME 
AUTO TUNE 
H-POSITION 
V-POSITION 
LANGUAGE
EXIT
The bar shows 
the progress of the 
adjustment being made.
Direct
z  Key Lock Mode:
With the power is off, press the 
 Button while pressing the Power Switch will switch the Key
Lock Mode On to Off. Adjustment items are locked out when the Key Lock Mode is active.
 
						

							ENGLISH
ADJUSTMENT MENU CONTENTS
Adjustment Item Problem / Option                       Button to Press
Page : 1
ANALOG Input
Direct
z  BRIGHTNESS:Press the  Button when the Menu is not displayed.
z  VOLUME: Press the + Button when the Menu is not displayed.
z  MUTE:Press the + Button when the Menu is not displayed, and then press the + and –
Buttons at the same time. To cancel MUTE, press the + Button.
OPERATING THE MONITOR     10
H : 60KHz 
V : 75Hz
50
§¥

b
b

1280x1024
ANALOG
EXIT SELECT
Page
Page
CONTRAST
BRIGHTNESS 
VOLUME 
AUTO TUNE 
H-POSITION 
V-POSITION 
LANGUAGE
EXIT
CONTRAST
BRIGHTNESS *
1Direct
AUTO TUNE *2
EXIT V-POSITION H-POSITION
LANGUAGE
Return to Menu.
RETURN TO MENU
VOLUMEToo dull
Too intense
Too dark
Too brightDirectToo soft
Too loud
Adjust Clock, Phase, V-Position and H-Poshition
automatically.
NOTE
The screen becomes dark for approximately five seconds during the adjustment.
„
Precision of adjustment is different by indicated pattern on the screen.
„
Too far to the left
Too far to the right
Too low
Too high
English
DeutschEnglish
German
Français French
Japanese Italiano Italian
Simplified Chinese
Español SpanishTraditional Chinese
*
1Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright.
*
2See page 13 for SCREEN ADJUSTMENTS.
You can skip the menu pages and display an adjustment scale directly by
using the following button operations. Exit OSD adjustments.
 
						

							ENGLISH
11     OPERATING THE MONITOR
To correct flickering text or lines
CLOCK
To correct flickering text or lines
Adjustment ItemProblem / Option                                           Button to Press
Page : 2
ANALOG Input1280x1024
ANALOG
EXIT SELECT
Page
Page
CLOCK
PHASE
RED 
GREEN 
BLUE 
COLOR TEMP.
RESET
EXIT
PHASE
RED
GREEN
COLOR TEMP.
RESET
EXITToo weak
Too strong
Too weak
Too strong
Reddish white
Bluish white Too weak
Too strong
Normal white
Factory-preset data is restored. Warm
Cool
Normal
Exit OSD adjustments. BLUE
 
						

							ENGLISH
Direct
Direct
OPERATING THE MONITOR     12
Adjustment Item Problem / Option                       Button to Press
Page : 1
DIGITAL Input
Direct
z  BRIGHTNESS:Press the  Button when the Menu is not displayed.
z  VOLUME: Press the + Button when the Menu is not displayed.
z  MUTE:Press the + Button when the Menu is not displayed, and then press the + and –
Buttons at the same time. To cancel MUTE, press the + Button. CONTRAST
BRIGHTNESS *
LANGUAGE
Return to Menu.
RETURN TO MENU VOLUMEToo dull
Too intense
Too dark
Too bright
Too soft
Too loud
English
DeutschEnglish
German
Français
Japanese Italiano Italian
Simplified Chinese
Español SpanishTraditional Chinese
* Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright.
You can skip the menu pages and display an adjustment scale directly by
using the following button operations.
COLOR TEMP.Reddish white
Bluish white
Normal white Warm
Cool
Normal
EXITExit OSD adjustments.
1280x1024
DIGITAL
EXIT SELECT
Page
Page
CONTRAST
BRIGHTNESS 
VOLUME 
LANGUAGE 
COLOR TEMP.
EXIT
French
 
						

							ENGLISH
13     OPERATING THE MONITOR
SCREEN ADJUSTMENTS
„The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
„ProLite T1530SR is designed to provide the best performance at resolution of 1024 × 768, but can not
provide the best at resolutions of less than 1024 × 768, because the picture is automatically stretched
to fit the full screen or displayed at optimum resolution. It is recommended to operate at resolution of
1024 × 768, in normal use.
„ProLite T1730SR and ProLite T1930SR are designed to provide the best performance at resolution
of 1280 × 1024, but can not provide the best at resolutions of less than 1280 × 1024 because the
picture is automatically stretched to fit the full screen or displayed at optimum resolution. It is
recommended to operate at resolution of 1280 × 1024 in normal use.
„Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
„It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
„Perform adjustments after a warm-up period of at least thirty minutes.
„Additional adjustments may be required after the Auto Set up depending on the resolution or signal timing.
„The Auto Set up may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Clock, Phase and
Position. The other way is performing each adjustment manually.
Perform the Auto Set up first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Set up, manual adjustments are required. Both adjustments should be made by
using the screen adjustment patterns in the Adjustment Program obtained via the iiyama web site
(http://www.iiyama.com).
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista.
A AA A
AStart “Adjustment Program”.
B BB B
BSelect the resolution for your monitor and the adjustment pattern appears.
[Adjustment pattern]
Zebra pattern
Color bar
Picture frame
16-level gray scale
 
						

							ENGLISH
F FF F
FAdjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.
NOTE„When the left side of the picture frame moves away from the left edge of the display
area during the Clock adjustment, adjust Clock and H-Position alternately.
„Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
„The picture may flicker during the V-Position, H-Position and Clock adjustment.
„In case the picture frame is bigger or smaller than the data display area after the Clock
adjustment, repeat the adjustments from step 
C.
„In the case that a strong flicker or blurs remain on a part of the screen, repeat the
adjustments from step 
E to readjust the Clock. If the flicker or blurs still remain then
set the refresh rate to 60Hz and repeat the adjustments from step 
C.
„Adjust the H-Position after the Phase adjustment if the horizontal position moves
during the adjustment. C CC C
CPress the Auto Button. (Direct adjustment)
Or perform the Auto Set up.
D DD D
DAdjust the image manually by following procedure below when the screen has a flicker
or blur, or the picture does not fit in the display area after performing the Auto Set up.
E EE E
EStretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
G GG G
GSelect “Position” in the Adjustment Program and adjust the V-Position and H-Position
so that the frame of cross-hatch pattern fits into the display area.
OPERATING THE MONITOR     14
 
						

							ENGLISH
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.NOTE
POWER MANAGEMENT FEATURE
„
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly. „
The monitor may not be restored from the power management depending on your
computer system even if the screen is touched again. In this case, set the power
management feature to off. „ Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the
monitor enters into Power Management Mode which reduces the power consumption to less than
2W. The screen becomes dark, and the power indicator turns to orange. From Power Management
Mode, the image reappears in several seconds when either the keyboard or the mouse are
touched again. The power management feature of this product complies with every power saving requirement of
VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the
monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system
manual for information on how this can be configured.
„
0  2 W 100% POWER
CONSUMPTION
Green
Orange
Power Indicator
NORMAL MODE
POWER MANAGEMENT MODE
H HH H
HSelect “Brightness” in the Adjustment Program and adjust the Back Light and
Contrast so that all 16 levels of gray in the grayscale pattern are visible.
Click on “FINISH” to close the Adjustment Program.
15     OPERATING THE MONITOR
 
						

							ENGLISH
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you
have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for
further assistance. 3.
Problem Check
The picture does
not appear.
(Power indicator
does not light up.)The Power Cable is firmly seated in the socket. †
†
†The AC socket is live. Please check with another piece of equipment.
†If the blank screen saver is in active mode, touch the keyboard or the
mouse.
†
Increase the Contrast and/or Back Light level.
The computer is ON.
†
The Signal Cable is properly connected. †The Power Switch is turned ON. A
(Power indicator
is green.)
†The signal timing of the computer is within the specification of the monitor.
(Power indicator
is orange.)
The computer is ON.
The Signal Cable is properly connected. †
† †
If the monitor is in power management mode, touch the keyboard or the
mouse.
The screen is not
synchronized.†The Signal Cable is properly connected.
†The signal timing of the computer is within the specification of the monitor. B†
The signal timing of the computer is within the specification of the monitor.
†The video output level of the computer is within the specification of the
monitor.
The screen
position is not in
the center.†The signal timing of the computer is within the specification of the monitor.
The screen is
too bright or too
dark.
The screen is
shaking. C
D
EThe video output level of the computer is within the specification of the
monitor. †
†The power voltage is within the specification of the monitor.
†
The signal timing of the computer is within the specification of the monitor. 1.
F†The RS-232C Cable or the USB Cable is firmly seated in the socket.
†
Touch screen driver software is installed. The touch
screen shows
no response.
G†The calibration function set up correctly.
The touch
position does not
deviate.
TROUBLE SHOOTING     16
 
						

							ENGLISH
17     APPENDIX
APPENDIX
4.3kg / 9.5lbs
SPECIFICATIONS : ProLite T1530SR
LCD
PanelDriving system
Sizea-Si TFT Active Matrix
Diagonal: 38cm  / 15.0
0.297mm H × 0.297mm V
Response time Pixel pitch
Display Colors Approx. 16.2 million
Sync FrequencyHorizontal: 31.0-60.0kHz, Vertical: 60-75Hz
Dot Clock80MHz maximum
Maximum Resolution 1024 × 768
Input Connector
Separate sync: TTL, Positive or Negative Plug & Play VESA DDC2B
TM
23W maximum, Power management (VESA DPMS) : 2W (Max)
Dimensions 351.0 × 314.5 × 140.0mm / 13.8 × 12.4× 5.5 (W×H×D)
Input Video Signal Analog:  0.7Vp-p  (Standard),  75Ω, Positive
Digital: DVI(Digital Visual Interface standard Rev.1.0)compliance
Viewable angle
Maximum Screen Size 304.1mm W × 228.1mm H / 12.0 W × 9.0 H
Power Source
Environmental
Considerations
Approvals
10 to 90% (No condensation)5 to 35°C / 41 to 95°F
-20 to 60°C / -4 to 140°F Operative temperature:
Storage temperature:
Storage humidity :20 to 80% (No condensation) Operative humidity: Touch
ScreenTechnology
Surface processing
Light transmissionResistive Film
Anti-glare treatment
USB serial transfer or RS-232C serial transfer Communication
system
DC12V, 4A
Power Consumption Input Sync Signal80%
Net Weight
CE, TÜV-SUD, FCC-B, UL / cUL,
VCCI-B D-Sub mini 15pin Brightness 280cd/m
2 (With touch panel)
500 : 1 (With touch panel) Contrast ratio
Horizontal: 120 degrees, Up: 40 degrees, Down: 60 degrees
16ms (Black, white, black   Typical)
DVI-D 24pin
Input Audio  Signal 0.7Vrms maximum
Speakers 1W × 2 (Stereo speakers)
Input Audio  Connector ø 3.5mm mini jack (Stereo)
Up: 90 degrees, Down: 5 degrees Tilt Angle
Model NameProLite T1530SR-1 ProLite T1530SR-2
200cd/m
2 (With touch panel)
8ms (Black, white, black   Typical)
CE, TÜV-SUD