Iiyama Prolite T1730sr User Manual
Have a look at the manual Iiyama Prolite T1730sr User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 49 iiyama manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![](/img/blank.gif)
USER MANUAL Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. DEUTSCH FRANCAIS ENGLISH NEDERLANDS
![](/img/blank.gif)
ENGLISH FCC DECLARATION OF CONFORMITY Model Number:PLT1500 / PLT1700 / PLT1900 The result of electromagnetic emission has been evaluated by Compliance Certification Service Inc. and showed in the test report. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for Class B Personal Computers and peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the device is operated in a residential environment. This device generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If you determine the device does cause harmful interference to radio or television reception (this may be determined by monitoring the interference while turning the device off and on), you are encouraged to try to correct the interference by one of the following measures: „Reorient or relocate the receiving antenna. „Increase the separation between the device and receiver. „Connect the device into an outlet on a circuit different from that to which the receiver is connected. „Consult the dealer or an experienced radio or TV technician for help. To meet the FCC requirements, you should use a signal cable with ferrite core at both ends. CAUTIONChanges or modifications not expressly approved by iiyama could void the users authority to operate the device under FCC compliance regulations. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulation of the Canadian department of communications. CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE STATEMENT „We reserve the right to change specifications without notice. „All trademarks used in this user manual are the property of their respective owners. CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC Directive 2004/108/EC “EMC Directive” and 2006/ 95/EC “Low Voltage Directive”. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.
![](/img/blank.gif)
ENGLISH TABLE OF CONTENTS FOR YOUR SAFETY .............................................................................. 1 SAFETY PRECAUTIONS................................................................. 1 SPECIAL NOTES ON LCD MONITORS............................................. 3 CUSTOMER SERVICE...................................................................... 3 CLEANING....................................................................................... 3 BEFORE YOU OPERATE THE MONITOR................................................ 4 FEATURES....................................................................................... 4 SPECIAL NOTES ON TOUCH PANEL............................................... 4 CHECKING THE CONTENTS OF THE PACKAGE............................. 5 WALL MOUNTING........................................................................... 5 CONTROLS AND CONNECTORS :................................................. 6 CONNECTING YOUR MONITOR :.................................................... 7 COMPUTER SETTING....................................................................... 8 ADJUSTING THE VIEWING ANGLE................................................. 8 OPERATING THE MONITOR................................................................... 9 ADJUSTMENT MENU CONTENTS.................................................... 10 SCREEN ADJUSTMENTS................................................................. 13 POWER MANAGEMENT FEATURE.................................................. 15 TROUBLE SHOOTING............................................................................ 16 APPENDIX.............................................................................................. 17 SPECIFICATIONS : ProLite T1530SR............................................... 17 SPECIFICATIONS : ProLite T1730SR............................................... 18 SPECIFICATIONS : ProLite T1930SR............................................... 19 DIMENSIONS.................................................................................... 20 COMPLIANT TIMING......................................................................... 21 We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address:http://www.iiyama.com You can access the Web page of different countries from there. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org). This information is only for U.S.A.. Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
![](/img/blank.gif)
ENGLISH FOR YOUR SAFETY WARNING STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock. DO NOT PUT ANY OBJECT INTO THE MONITOR Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fire, electric shock or damage. DO NOT DROP AND DO NOT GIVE A SHOCK The monitor may cause an injury if it falls or is dropped. Be careful with chips of glass, may cause injuring fingers or skin, when the glass is broken. Do not ingest the liquid crystal and do not touch the liquid crystal with skin or cloths if LCD panel is broken and liquid crystal leaks. If liquid crystal touch eyes, mouth, skin or cloths, immediately rinse with water for over 15 minutes. If ingested immediately rinse with water, and then spit out after drink water. After that, consult a doctor. DO NOT USE THE MONITOR NEAR WATER Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric shock. OPERATE UNDER THE SPECIFIED POWER SUPPLY Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will cause malfunction and may cause fire or electric shock. PROTECT THE CABLES Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy objects on the cables. If damaged, the cables may cause fire or electric shock. ADVERSE WEATHER CONDITIONS It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction. It is also advised not to touch the plug in these circumstances as it may cause electric shock. SAFETY PRECAUTIONS 1 FOR YOUR SAFETY
![](/img/blank.gif)
ENGLISH FOR YOUR SAFETY 2 CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located. Please also ensure that you do not place any heavy objects on the monitor, and that all cables are routed such that children may not pull the cables and possibly cause injury. MAINTAIN GOOD VENTILATION Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls. Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage. Operating the monitor on its back, side, upside down or on a carpet or any other soft material may also cause damage. We suggest installing a cooling fan when placing the monitor into a rack. DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal cable is disconnected. If you do not disconnect them, it may cause fire or electric shock. UNPLUG THE MONITOR If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents. HOLD THE PLUG WHEN DISCONNECTING To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself as this may cause fire or electric shock. DO NOT TOUCH THE PLUG WITH WET HANDS Pulling or inserting the plug with wet hands may cause electric shock. WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage your computer. ERGONOMIC RECOMMENDATIONS To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches) away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain. OTHERS
![](/img/blank.gif)
ENGLISH 3 FOR YOUR SAFETY NOTEThe fluorescent light used in the LCD monitor may have to be periodically replaced. For the warranty coverage on this component, please check with local iiyama service center. If you have to return your unit for service and the original packaging has been discarded, please contact your dealer or iiyama service center for advice or replacement packaging. „ „ WARNINGIf you drop any materials or liquids such as water into the monitor when cleaning, unplug the power cable immediately and contact your dealer or iiyama service center. „ CAUTIONFor safety reasons, turn off the power switch and unplug the monitor before you clean it. „ To protect the LCD panel, do not scratch or rub the screen with a hard object. „ Never use any of the following strong solvents. These will damage the cabinet and the LCD screen. Thinner Benzine Abrasive cleanerSpray-type cleaner Wax Acid or Alkaline solvent Touching the cabinet and the LCD screen with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet and the LCD screen. „ CABINETStains can be removed with a cloth lightly moistened with a mild detergent solvent. Then wipe the cabinet with a soft dry cloth. LCD SCREENPeriodic cleaning with a soft dry cloth is recommended. Don’t use tissue paper etc. because these will damage the LCD screen. Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then wipe the touch screen with a soft dry cloth. Don’t pour the detergent solvent on the touch screen. CUSTOMER SERVICE CLEANING „ NOTE The following symptoms are normal with LCD monitors and do not indicate a problem. NOTEWhen you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. „ Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. There is the possibility that the previous screen has been fixed. Pay attention sufficient when you use LCD Monitor. „You may find slightly uneven brightness on the screen depending on the desktop pattern you use. „ Contact your dealer or iiyama service center for the backlight replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself. „Due to the nature of the backlight, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. „ SPECIAL NOTES ON LCD MONITORS „Condensation may appear between Touch screen and LCD screen. It is the natural phenomenon and it is not a malfunction. Condensation disappears with slowly warming the whole unit. Non condensing when the unit is in-use, it will cause defective symptoms.
![](/img/blank.gif)
ENGLISH BEFORE YOU OPERATE THE MONITOR 4 FEATURES ‹ ‹‹ ‹ ‹ProLite T1530SR : 38cm (15.0) TFT Color LCD Monitor Resistive Film ‹ ‹‹ ‹ ‹ProLite T1730SR : 43cm (17.0) TFT Color LCD Monitor Resistive Film ‹ ‹‹ ‹ ‹ProLite T1930SR : 48cm (19.0) TFT Color LCD Monitor Resistive Film ‹ ‹‹ ‹ ‹ProLite T1530SR: Supports Resolutions up to 1024 × 768 ‹ ‹‹ ‹ ‹ProLite T1730SR / ProLite T1930SR : Supports Resolutions up to 1280 × 1024 ‹ ‹‹ ‹ ‹Digital Character Smoothing ‹ ‹‹ ‹ ‹Automatic Set-up ‹ ‹‹ ‹ ‹Plug & Play VESA DDC2B Compliant Windows ® 95/98/2000/Me/XP/Vista Compliant ‹ ‹‹ ‹ ‹Power Management (VESA DPMS Compliant) ‹ ‹‹ ‹ ‹ProLite T1530SR : VESA Standard (75mm×75mm) for Arm or Wall Mounting ‹ ‹‹ ‹ ‹ProLite T1730SR / ProLite T1930SR : VESA Standard (100mm×100mm) for Arm or Wall Mounting ‹ ‹‹ ‹ ‹Stereo Speakers BEFORE YOU OPERATE THE MONITOR SPECIAL NOTES ON TOUCH PANEL Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch. This could invalidate any remaining warranty. We recommend to use a plastic stylus (tip R0.8 or over) or finger.
![](/img/blank.gif)
ENGLISH The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office. CHECKING THE CONTENTS OF THE PACKAGE 5 BEFORE YOU OPERATE THE MONITOR CAUTION*1 1. TO USERS IN 120V AREA The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using a power supply higher than this rating, then a power cable with a rating of 10A/ 250V must be used. However, all guarantees and warranties are void for any problems or damage caused by a power cable or AC adapter not supplied by iiyama. 2. AC Adapter Type Name : LSE9901B1250 (LI SHIN INTERNATIONAL ENTERPRISE CORP.) * 2This CD-ROM contains the touch screen driver software. Install the Touch Panel Driver Disk after connecting the computer to the monitor with RS-232C Cable or USB Cable. For the details, see Readme file in the Touch Panel Driver Disk. Screw Chassis Mounting Stage L WALL MOUNTING WARNINGWhen you use with the wall mounting, in consideration of thickness of the mounting stage, tighten the M4 Screw with washer which “L” length is 6mm to fasten the monitor. Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor. 1530SR1730SR 1930SRProLite T Accessories User Manual AC Adapter* 1 Power Cable*1 D-Sub Signal Cable DVI-D Signal Cable RS-232C Cable USB Cable Audio Cable Touch Panel Driver Disk (CD-ROM)* 2 { {{ {{ {{ {{ {{ {{ {{ {{
![](/img/blank.gif)
ENGLISH BEFORE YOU OPERATE THE MONITOR 6 CONTROLS AND CONNECTORS A / Menu Button ( / MENU) B / Brightness Button ( / ) C+ / Volume Button (+ / ) D– / Input Button (– / INPUT ) With the OSD menu off, pressing the Input Button will switch the input signal from D- SUB to DVI. EPower Indicator Green: Normal operation Orange: Power Management The monitor enters into power management mode which reduces the power consumption to less than 2W when receiving no horizontal and/or vertical sync signal. FSpeakers GPower Switch ( ) Holding the Power Switch will turn off the power. HConnector for AC Adapter (DC-in)* 1 ID-Sub mini 15pin Connector (D-SUB) JDVI-D 24pin Connector (DVI) KAudio Connector (AUDIO in) LUSB Cable Connector ( ) MRS-232C Cable Connector ( ) NKeyhole for Security Lock* 3 „You can fasten a security lock and cable to prevent the monitor from being removed without your permission. OKeyhole for Security Lock* 4 „You can fasten a security lock and cable to prevent the monitor from being removed without your permission. PAC Connector (AC in)* 2 *1 Available for ProLite T1530SR only. * 2 Available for ProLite T1730SR and ProLite T1930SR only. * 3 Available for ProLite T1530SR and ProLite T1730SR only. * 4 Available for ProLite T1930SR only. NOTE NOTE NOTE NOTE NOTE
![](/img/blank.gif)
ENGLISH CONNECTING YOUR MONITOR [Example of Connection] AEnsure that both the computer and the monitor are switched off. BConnect the computer to the monitor with the Signal Cable. CConnect the computer to the monitor with the RS-232C Cable or the USB Cable. DConnect the monitor to the audio equipment with the Audio Cable when using the audio features. EConnect the Power Cable to the monitor first and then to the power supply. NOTE„The signal cables used for connecting the computer and monitor vary by the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office. „For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor. „Make sure you tighten the finger screws at each end of the Signal Cable and the RS- 232C Cable. „Dont connect the RS-232C cable and the USB cable to the computer at the same time. And cannot use those at the same time. < Back > Audio Cable (Accessory) RS-232C Cable (Accessory) Computer D-Sub Signal Cable (Accessory) DVI-D Signal Cable (Accessory) AC Adapter (Accessory) Power Cable (Accessory) USB Cable (Accessory) Power Cable (Accessory)*2 *1 *1 *1 Available for ProLite T1530SR only. * 2 Available for ProLite T1730SR and ProLite T1930SR only. 7 BEFORE YOU OPERATE THE MONITOR