Icom Ic-r3 Communications Reciever Instruction Manual
Here you can view all the pages of manual Icom Ic-r3 Communications Reciever Instruction Manual. The Icom manuals for Communications receiver are available online for free. You can easily download all the documents as PDF.
Page 31
![Page 31
◊VFO scan watch
qSelect the desired memory channel to be watched.
wPush [V/M] to select VFO mode.
ePush [↔] for 2 sec. to start full scan, band scan or pro-
grammed scan. (p. 19)
rPush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
tRotate [DIAL] to select “Priority” or “PRIo.”
•“PRIo” disappears after 1 sec. and “oFF” and “PR” appears when
color LCD is OFF.
yPush [↔] or rotate the tuning dial while pushing [FUNC] to
select priority watch ON...](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-30.png "Page 31
◊VFO scan watch
qSelect the desired memory channel to be watched.
wPush [V/M] to select VFO mode.
ePush [↔] for 2 sec. to start full scan, band scan or pro-
grammed scan. (p. 19)
rPush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
tRotate [DIAL] to select “Priority” or “PRIo.”
•“PRIo” disappears after 1 sec. and “oFF” and “PR” appears when
color LCD is OFF.
yPush [↔] or rotate the tuning dial while pushing [FUNC] to
select priority watch ON...")
◊VFO scan watch qSelect the desired memory channel to be watched. wPush [V/M] to select VFO mode. ePush [↔] for 2 sec. to start full scan, band scan or pro- grammed scan. (p. 19) rPush [FUNC] + [(MODE) SET] momentarily to enter set mode. •Select a non-band scope screen in advance for color LCD. tRotate [DIAL] to select “Priority” or “PRIo.” •“PRIo” disappears after 1 sec. and “oFF” and “PR” appears when color LCD is OFF. yPush [↔] or rotate the tuning dial while pushing [FUNC] to select priority watch ON...
Page 32
![Page 32
28
8SUBAUDIBLE TONE OPERATION
Tone squelch operation
◊Operation
The tone squelch opens only when receiving a signal con-
taining a matching subaudible tone. You can silently wait for
calls from group members using the same tone in an ama-
teur band.
qSet the operating frequency in FM mode.
wSet the desired subaudible tone in set mode.
•See the following section for programming.
ePush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
rRotate...](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-31.png "Page 32
28
8SUBAUDIBLE TONE OPERATION
Tone squelch operation
◊Operation
The tone squelch opens only when receiving a signal con-
taining a matching subaudible tone. You can silently wait for
calls from group members using the same tone in an ama-
teur band.
qSet the operating frequency in FM mode.
wSet the desired subaudible tone in set mode.
•See the following section for programming.
ePush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
rRotate...")
28 8SUBAUDIBLE TONE OPERATION Tone squelch operation ◊Operation The tone squelch opens only when receiving a signal con- taining a matching subaudible tone. You can silently wait for calls from group members using the same tone in an ama- teur band. qSet the operating frequency in FM mode. wSet the desired subaudible tone in set mode. •See the following section for programming. ePush [FUNC] + [(MODE) SET] momentarily to enter set mode. •Select a non-band scope screen in advance for color LCD. rRotate...
Page 33
![Page 33
•Each operating band and each memory channel have indepen-
dent settings.
wPush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
eRotate [DIAL] until “Tone Freq.” or “tonE” appears.
•“tonE” disappears after 1 sec. and “Ct” appears.
rPush [↔] or rotate the tuning dial while pushing [FUNC] to
select a subaudible tone.
tPush [(MODE) SET] to exit set mode.
•Available subaudible tone frequencies (unit: Hz)](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-32.png "Page 33
•Each operating band and each memory channel have indepen-
dent settings.
wPush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
eRotate [DIAL] until “Tone Freq.” or “tonE” appears.
•“tonE” disappears after 1 sec. and “Ct” appears.
rPush [↔] or rotate the tuning dial while pushing [FUNC] to
select a subaudible tone.
tPush [(MODE) SET] to exit set mode.
•Available subaudible tone frequencies (unit: Hz)")
•Each operating band and each memory channel have indepen- dent settings. wPush [FUNC] + [(MODE) SET] momentarily to enter set mode. •Select a non-band scope screen in advance for color LCD. eRotate [DIAL] until “Tone Freq.” or “tonE” appears. •“tonE” disappears after 1 sec. and “Ct” appears. rPush [↔] or rotate the tuning dial while pushing [FUNC] to select a subaudible tone. tPush [(MODE) SET] to exit set mode. •Available subaudible tone frequencies (unit: Hz)
Page 34
![Page 34
30
8SUBAUDIBLE TONE OPERATION
tRotate [DIAL] until “Tone Squelch” or “tSqL” appears.
•“tSqL” disappears after 1 sec. and “to” appears when color LCD
is OFF.
yPush [↔] or rotate the tuning dial while pushing [FUNC] to
select “P BEEP” (pocket beep).
uPush [(MODE) SET] to exit set mode and start the pocket
beep.
•“P. B” or “T SQLë” appears in the function display.
iWhen a signal with the correct tone is received, the re-
ceiver emits beep tones for 30 sec. and flashes “P. B” or
“ë.”
oPush [SQL] to stop the...](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-33.png "Page 34
30
8SUBAUDIBLE TONE OPERATION
tRotate [DIAL] until “Tone Squelch” or “tSqL” appears.
•“tSqL” disappears after 1 sec. and “to” appears when color LCD
is OFF.
yPush [↔] or rotate the tuning dial while pushing [FUNC] to
select “P BEEP” (pocket beep).
uPush [(MODE) SET] to exit set mode and start the pocket
beep.
•“P. B” or “T SQLë” appears in the function display.
iWhen a signal with the correct tone is received, the re-
ceiver emits beep tones for 30 sec. and flashes “P. B” or
“ë.”
oPush [SQL] to stop the...")
30 8SUBAUDIBLE TONE OPERATION tRotate [DIAL] until “Tone Squelch” or “tSqL” appears. •“tSqL” disappears after 1 sec. and “to” appears when color LCD is OFF. yPush [↔] or rotate the tuning dial while pushing [FUNC] to select “P BEEP” (pocket beep). uPush [(MODE) SET] to exit set mode and start the pocket beep. •“P. B” or “T SQLë” appears in the function display. iWhen a signal with the correct tone is received, the re- ceiver emits beep tones for 30 sec. and flashes “P. B” or “ë.” oPush [SQL] to stop the...
Page 35
31 9DUPLEX OPERATION Duplex communication uses 2 different frequencies for trans- mitting and receiving. Generally, duplex is used in communi- cation through a repeater, some utility communications, etc. During duplex operation, the transmit station frequency is shifted from the receive station frequency by the offset fre- quency. Repeater information (offset frequency and shift di- rection) can be programmed into memory channels. (p. 14) This function is not available in the broadcast band (0.495 –1.620...
Page 36
![Page 36
32
9DUPLEX OPERATION
◊Offset frequency
During duplex operation, the transmit station frequency is
shifted from the receive station frequency by an amount de-
termined by the offset frequency.
qSelect VFO mode or desired memory channel to be pro-
grammed.
wPush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
eRotate [DIAL] until “Offset Freq.” or “oFFSEt” appears.
•“oFFSEt” disappears after 1 sec. and “oW” appears when the
color LCD is OFF....](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-35.png "Page 36
32
9DUPLEX OPERATION
◊Offset frequency
During duplex operation, the transmit station frequency is
shifted from the receive station frequency by an amount de-
termined by the offset frequency.
qSelect VFO mode or desired memory channel to be pro-
grammed.
wPush [FUNC] + [(MODE) SET] momentarily to enter set
mode.
•Select a non-band scope screen in advance for color LCD.
eRotate [DIAL] until “Offset Freq.” or “oFFSEt” appears.
•“oFFSEt” disappears after 1 sec. and “oW” appears when the
color LCD is OFF....")
32 9DUPLEX OPERATION ◊Offset frequency During duplex operation, the transmit station frequency is shifted from the receive station frequency by an amount de- termined by the offset frequency. qSelect VFO mode or desired memory channel to be pro- grammed. wPush [FUNC] + [(MODE) SET] momentarily to enter set mode. •Select a non-band scope screen in advance for color LCD. eRotate [DIAL] until “Offset Freq.” or “oFFSEt” appears. •“oFFSEt” disappears after 1 sec. and “oW” appears when the color LCD is OFF....
Page 37
![Page 37
33
10BAND SCOPE
The band scope function allows you to visually check a spec-
ified frequency range. Sweep range can be selected from ±5
kHz through ±500 kHz.
Receive audio is muted while monitoring the band scope.
Push [SQL] to cancel sweeping and receive the audio.
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON.
wPush [FUNC] + [↕] one or more times to select the band
scope screen.
eSet the desired frequency as band scope center frequency.
rPush [FUNC] + [V/M] momentarily to select the sweep...](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-36.png "Page 37
33
10BAND SCOPE
The band scope function allows you to visually check a spec-
ified frequency range. Sweep range can be selected from ±5
kHz through ±500 kHz.
Receive audio is muted while monitoring the band scope.
Push [SQL] to cancel sweeping and receive the audio.
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON.
wPush [FUNC] + [↕] one or more times to select the band
scope screen.
eSet the desired frequency as band scope center frequency.
rPush [FUNC] + [V/M] momentarily to select the sweep...")
33 10BAND SCOPE The band scope function allows you to visually check a spec- ified frequency range. Sweep range can be selected from ±5 kHz through ±500 kHz. Receive audio is muted while monitoring the band scope. Push [SQL] to cancel sweeping and receive the audio. qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON. wPush [FUNC] + [↕] one or more times to select the band scope screen. eSet the desired frequency as band scope center frequency. rPush [FUNC] + [V/M] momentarily to select the sweep...
Page 38
![Page 38
34
11TV OPERATION
TV operation
The receiver can receive TV (NTSC or PAL depending on ver-
sion). TV channels are preset depending on versions.
The received video and audio can be output from [A/V OUT] if
desired.
◊TV channel receiving
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if
desired.
•Only the audio part of the TV contents can be received.
wPush [↔] one or more times to select the TV channel
band.
•“tV” and channel number appear in the sub LCD.
•The squelch is automatically opened....](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-37.png "Page 38
34
11TV OPERATION
TV operation
The receiver can receive TV (NTSC or PAL depending on ver-
sion). TV channels are preset depending on versions.
The received video and audio can be output from [A/V OUT] if
desired.
◊TV channel receiving
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if
desired.
•Only the audio part of the TV contents can be received.
wPush [↔] one or more times to select the TV channel
band.
•“tV” and channel number appear in the sub LCD.
•The squelch is automatically opened....")
34 11TV OPERATION TV operation The receiver can receive TV (NTSC or PAL depending on ver- sion). TV channels are preset depending on versions. The received video and audio can be output from [A/V OUT] if desired. ◊TV channel receiving qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if desired. •Only the audio part of the TV contents can be received. wPush [↔] one or more times to select the TV channel band. •“tV” and channel number appear in the sub LCD. •The squelch is automatically opened....
Page 39
![Page 39
35
11TV OPERATION
◊TV frequency (AM TV) receiving
You can set the TV frequency instead of channel selection, if
desired.
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if
desired.
•The audio part of the TV contents can be received when the
color LCD is turned OFF.
wPush [↔] one or more times to select the band above 30
MHz.
•TV receiving does not function for less than 30 MHz.
ePush [FUNC] + [↕] one or more times to select the TV
screen.
•“tV” and frequency appear in the sub LCD.
•The squelch is...](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-38.png "Page 39
35
11TV OPERATION
◊TV frequency (AM TV) receiving
You can set the TV frequency instead of channel selection, if
desired.
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if
desired.
•The audio part of the TV contents can be received when the
color LCD is turned OFF.
wPush [↔] one or more times to select the band above 30
MHz.
•TV receiving does not function for less than 30 MHz.
ePush [FUNC] + [↕] one or more times to select the TV
screen.
•“tV” and frequency appear in the sub LCD.
•The squelch is...")
35 11TV OPERATION ◊TV frequency (AM TV) receiving You can set the TV frequency instead of channel selection, if desired. qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if desired. •The audio part of the TV contents can be received when the color LCD is turned OFF. wPush [↔] one or more times to select the band above 30 MHz. •TV receiving does not function for less than 30 MHz. ePush [FUNC] + [↕] one or more times to select the TV screen. •“tV” and frequency appear in the sub LCD. •The squelch is...
Page 40
![Page 40
36
11TV OPERATION
ATV operation
The IC-R3 ATV-type can receive an amateur TV (FM TV)
within 900–1300 and 2250–2450.095 MHz. The received
video and audio can be output from [A/V OUT] if desired. (p.
5)
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if
desired.
•Only the audio part of the TV contents can be received.
wPush [↔] one or more times to select the 1200 or 2400
MHz bands.
ePush [FUNC] + [↕] one or more times to select the ama-
teur TV screen.
•“FtV” and frequency appear in the sub LCD....](http://img.usermanuals.tech/thumb/2452/82811/w300_icom_r3-comms-scanner-reciever_manual_d-39.png "Page 40
36
11TV OPERATION
ATV operation
The IC-R3 ATV-type can receive an amateur TV (FM TV)
within 900–1300 and 2250–2450.095 MHz. The received
video and audio can be output from [A/V OUT] if desired. (p.
5)
qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if
desired.
•Only the audio part of the TV contents can be received.
wPush [↔] one or more times to select the 1200 or 2400
MHz bands.
ePush [FUNC] + [↕] one or more times to select the ama-
teur TV screen.
•“FtV” and frequency appear in the sub LCD....")
36 11TV OPERATION ATV operation The IC-R3 ATV-type can receive an amateur TV (FM TV) within 900–1300 and 2250–2450.095 MHz. The received video and audio can be output from [A/V OUT] if desired. (p. 5) qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if desired. •Only the audio part of the TV contents can be received. wPush [↔] one or more times to select the 1200 or 2400 MHz bands. ePush [FUNC] + [↕] one or more times to select the ama- teur TV screen. •“FtV” and frequency appear in the sub LCD....