Hyundai H Lcd3202 Instruction Manual

H-LCD3202
LCD TV   @DL?E?

2 Table of contentsTable of contents ......................................................................................................................................... 2
Important safety precautions ........................................................................................................................ 3
General introduction .................................................................................................................................... 5...

3 Important safety precautions Warning
Please unplug the power cord from the AC outlet and contact our service personnel to repair under the fol-lowing conditions:xAny obvious abnormality appears in the product, such as smoky, peculiar smell or strange sound.
xWhen a liquid has been spilled or other objects have fallen into the product.
xNo picture or sound.
xCover or panel is broken.
xAlthough you have operated the product by following the operating instructions, it still cannot work
normally....

4 xFasten the wheel of the product or shelf with wheels when installing this product. If it moves or is
tipped over, it may be damaged.
xDo not place any fire source such as candlelight close to this product or place it on this product.
If it is tipped over or fallen down, it may cause damage or fire.  Caution: Do not place the LCD TV into closed space of TV for better ventilation; it can reduce the
product lifetime. Keep a space at list 10cm at above, left, and right of the TV.
Remote control
xDo not...

5 General introductionxSize of the screen: 32/81 cm
xAspect ratio: 16:9
xScreen resolution: 1366 x 768
xBrightness: 500 cd/m2
xContrast: 2000:1
xWide viewing angle 170º/170º
xResponse time: 8 ms
xProgressive scan
xColor systems: PAL, SECAM
xDigital comb filter
xNICAM Stereo
x“Picture in picture”
xTeletext
xConvenient OSD menu in Russian and English languages
xConnections: 2 HDMI, VGA, component video input, composite video PC audio input, 2 SCART jacks,
RF antenna
xPC monitor compatible...

6 Controls and connection   Front panel  Right panel
Top panel button description
ButtonDescriptionAC (Power) switchTurn on the AC switch; the TV will enter into standby mode. When a complete turn-
ing off is required, please turn off the AC switch and unplug the power cable from
the power socket.TV/AVTo switch among the signal source.MENUOpen the menu or switch among the menus.CH+/-In T V mode, decrease/increase channel number. Select functions in menu operation.VOL+/-Decrease/increase the sound volume....

7 Rear panel
Rear panel terminals and controls
I temsConnection description1  HDMI 1, 2Connect one end of the HDMI cable with HDMI output port, connect the other
end of the HDMI cable with the HDMI port on the TV, and tighten the bolts
clockwise on the each end of HDMI cable.2 VGAConnect one end of the VGA cable with the VGA port on computer, connect the
other end of the VGA cable with the VGA port on the TV, and tighten the bolts
clockwise on the each end of VGA cable.3  PC audio inConnect it to the...

8Remote control (RC)
1.  POWER button. Press to turn on/off the TV
set or to switch it to standby mode.
2.  MUTE button. Press to turn off/on the sound.
3.  Number buttons. Press to input figures.
4.  LAST CHANNEL button. Press to switch to
the last watched channel.
5.  SYSTEM button. Press to adjust audio pa-
rameters.
6.  NICAM A2 button. Press to turn on/off the
NICAM function.
7.  VOL+/VOL- button. Press to adjust the sound
volume level.
8.  CH+/CH- button. Press to switch between
channels.
9....

9 Note:If the RC doesn’t react to pressing the buttons or the working range was decreased insert the new bat-
teries.
Use of RC
Use the RC by pointing it towards the RC sensor of the set. Objects between the RC and sensor may prevent
proper operation.
Note: The illustration is for your reference only; the remote sensor ma y locate different ly with different
model.
Cautions regarding use of RC
xDo not expose the RC to liquids, and do not place in an area with high humidity.
xDo not install or place the...

10 OSD operationsSEARCH Menu (in TV mode)
Press MENU button to display the OSD menu; press UP/DOWN buttons to
select the Search menu, then press RIGHT button to enter the menu. Now
you can use UP/DOWN buttons to select the submenu: Auto Tuning,
Search, Program Edit. Press MENU button to return to the main menu.
Press RIGHT button to enter the submenu.
Auto Tuning
Press UP/DOWN buttons to select Auto Tuning;
press RIGHT button to enter it.
S ys tem: It is conditioned by the Country item.
Auto Search:...