Husqvarna X 4000 Manual

Soff-Cut 4000
Please read the operator’ s manual carefully and make sur e you 
understand the instructions befor e using the machine.GB
Operator’s manual 

CONTENTS
Content            Page 
Table of contents   …………………………..  2Unpacking ..................................................  2Transporting ...............................................  2
Sound Data ................................................  2
Introduction, personal safety ......................  3 
Registration of the product …………………  4
General safety message ............................  4
Safety warnings .........................................  5
Excel series blades...

INTRODUCTION
 
Common sense:
The focus of this manual is HOW to operate and service the equipment saf\
ely.  
It is not possible to cover every conceivable situation you can face whe\
n using this equipment.  Therefore use this product only in a manner described in this manual.  Operation or handling the machine in any other manner can 
lead to serious injury or death.
If a situation is not described in this manual it should be considered d\
angerous - and not be done.
If you are unfamiliar with this...

4
REGISTER THE PRODUCT
Please register your new Soff-Cut 4000 with Husqvarna Construction Products by mailing
in the registration card that came with the machine or you can register on the internet site  
www.husqvarnawarranty.com
Registration will allow us to contact in case of any critical updates or\
 recalls on this machine.   
Warranty registration has also been found to be helpful in tracing stolen equipment.
Record the following information for your records:
PURCHASE DATE: ________________
MODEL...

5
SAFETY WARNINGS
WARNING 
Failure to comply with the following warnings could 
result in serious bodily injury or death!
PERSONAL SAFETY
• Read and understand instructions before operating saw.
• Always wear safety approved hearing, eye, head and 
  respiratory protection.
• Wear boots with non-slip soles to provide proper footing.         
  Steel-toed safety boots are recommended.
• Wear rubber work gloves to avoid contact with wet concrete  
  which can cause serious skin irritation.
• Know how to...

6
EXCEL SERIES BLADES
The Excel Series of diamond blades have been designed specifically for the Soff-Cut Ultra Early Entry dry cutting system of 
green concrete. These specialty blades are designed to increase speed and life while cut\
ting a wide range of aggregates. 
Choose the correct specification of diamond blade for your area as follows:
 Purple Excel Series 1000    XL14-1000 Ultra hard aggregate and non abrasive sand
 Green Excel Series 2000    XL14-2000 Hard to ultra hard aggregate and non...

WHAT IS WHAT
HC
B
I
A
O
F
What is what?     
 
A. Oil fill cap
B. Oil filter
C. Engine on/off switch
D. Air cleaner
E. Fuel filter
F. Choke lever
G. Oil dipstick
H. Battery box
I. Oil drain hose
J. Fuel tank
K. Fuel cap
L. Hour meter/Tachometer
M. Saw forward speed lever
N. Guide arm lever
O. Engine throttle control
P. Blade depth switch
Q. Transmission oil fill cap
R. Cut depth pointer 
Model number and serial 
number
7
Q
J
D
G
E
K
N
ML
R
P 

8
OPERATING INSTRUCTIONS
Experience is very important when running the  saw. A 
skilled worker is highly recommended. Always do an inspection of the saw before starting the engine. Check the fuel (J) and 
oil level (G) per the enclosed engine manual. SAE 10W/30 oil 
and unleaded gasoline with an 87 or higher octane should be 
used. The hydrostatic tansmission use Mobil DTE 26 hydraulic 
oil or equivalent (20W with viscosity of 68).  Observe all safety 
regulations for the safe handling of fuel . Always...

9
FUEL HANDLING
PROPER FUEL
Taking the following precautions will lessen the risk 
of injury and property damage:
- Use extreme care in handling gasoline. It is  
  extremely flammable and the vapors are explosive. 
- Extinguish all cigarettes, cigars, pipes, and other               
  sources of ignition.
- Use only approved gasoline containers.
- Never remove gas cap or add fuel with the engine     
  running.  Allow engine to cool a minimum of 3 
  minutes before refueling.
- Never fuel the machine...

10
Engine Oil
Checking, Adding and Changing Oil
Check the engine oil level (A) daily with saw fully lowered and 
the engine level. See the enclosed Kohler manual for more 
details.
Use SAE 10W-30 viscosity detergent automotive type with API 
service class SE or higher grade oil.
Note: Engine holds approximately 2 quart (1.9 liter) when 
changing oil and oil filter.
Changing the Oil 
Change oil after the first 5 to 8 hours of use.
Thereafter every 50 hours. 
ENGINE AND TRANSMISSION MAINTENANCE 
Fuel...