Husqvarna P-zt 60 Manual

Moving Machine By Hand
When pushing or pulling the mower, engage the bypass linkages with the hydro release levers. The levers are located on each side of the rear of the unit below the engine plate.
  WARNING!  Bypass linkages are located close to the muffler. To prevent burns, the engine should be shut off and allowed to cool before the bypass linkage levels are handled.
  WARNING!  Do not make adjustments unless:
• the engine stopped,
• the ignition key removed,
• the park brake activated
1. Raise the...

Maintenance Schedule
Following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop 
MAINTENANCE
DAILY
AT  LEAST ONCE EACH YEAR
MAINTENANCE INTERVAL IN HOURS
BEFOREAFTER50250500
CHECK
Park brake for adjustment●●●●●
Engine’s oil level (every refueling)■
Safety system●
For fuel and oil leakages♦
For damage♦♦♦♦
For loose hardware (screws,...

  WARNING!  Before performing service or adjustment:
• Engage the park brake.• Place the Blade-switch in the disengaged position.• Turn the ignition switch to OFF position and remove the key.• Make sure the blades and all moving parts have completely stopped.
  WARNING! Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is...

Battery
Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• See chart for charging times.
Battery Removal
Corrosion and dirt on the battery and terminals can cause the battery to lose power.
1. Lift the seat and rotate fully forward until supported by the seat rod.
2. Loosen the two wingnuts attached to...

Safety System
The machine is equipped with a safety system that prevents starting or driving under the following conditions.
The engine can only be started when:
• the mower deck is disengaged.
• the steering controls are in the outer, locked neutral position.
• the park brake is on.
IMPORTANT INFORMATION  To be able to drive, the driver must sit in the seat and release the park brake before the steering controls can be moved into the neutral position, otherwise the engine will stop.
Tire Pressures
All...

Deck Belt
Deck Belt Removal
Park on a level surface. Apply park brake. Lower the deck into the lowest cutting position.
1. Remove foot plate and belt shields.
2. Remove dirt or grass that may have accumulated around the cutter housings and entire deck surface.
3. With a 1/2" breaker bar and using the square opening in the idler arm, shift the arm counter clockwise to relieve the tension on the belt.
4. Carefully lift the belt over the top of the cutter housing pulleys.
5. Remove the belt guide...

Cutting Blades
To attain the best mowing effect, it is important that blades are well sharpened and not damaged.
Replace blades that have been bent or cracked when hitting obstacles.
Let the service workshop decide whether a blade with large nicks can be repaired/ground or must be replaced. Balance the blades after sharpening.
Check the blade mounts.
Blade Replacement
1. Remove blade bolt by turning it counter clockwise.
2. Install new or re-sharpened blade with stamped GRASS SIDE facing towards...

Anti-scalp Rollers
Anti-scalp rollers keep the deck in the proper position to help prevent scalping in most terrain conditions. Do not adjust the rollers to support the deck.
IMPORTANT INFORMATION  Adjust anti-scalp rollers with the mower on a flat level surface.
To avoid deck damage, the anti-scalp rollers must not be adjusted to support the deck.
Anti-scalp rollers can be set in three positions.
• Upper position 1-1/2" to 2-1/2" grass
• Middle position 2-1/2" to 4" grass
• Lower...

ZT-3400 Powertrain
General
Remove the ignition key to prevent unintentional movements during lubrication.
When lubricating with an oil can, it must be filled with engine oil.
When lubricating with grease, unless otherwise stated, use high grade molybdenum disulphide grease.
For daily use, the machine should be lubricated twice weekly.
* Change hydraulic drive filters.
p Change engine oil every 50 hours.
12/12Every yearLubricate with grease gun
1/52Every WeekFilter change
1/365Every dayOil change
Level...

Drain old oil filters of all free-flowing oil prior to disposal. Place used oil in appropriate containers and dispose of it in accordance with laws in your area.
Transaxle Fluid Change
This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life, an oil filter change interval of every 200 hours is recommended.
The following procedure is performed with the transaxles installed in the mower and the mower on level ground. Apply the pump...