Home > Husqvarna > Sewing Machine > Husqvarna Designer 1 Service Manual

Husqvarna Designer 1 Service Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Husqvarna Designer 1 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 35 Husqvarna manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							              11 104 72 47-26
    Press
     Update of the memory
    The Designer 1 has a  memory in which the characteristics
    and stitches of the machine are stored.
    In order to update the memory the machine has an
    update mode.
    Revision of the program
    The revision of the program can be seen in
    the  lower right side of welcome screen or
    checked in the service program  menu 1
    How to update
    1 . Insert the disk with the new memory
    information in the floppy disk drive.
    2 . Get into the update mode of the machine
    by pressing the start/stop button
    and the stitch re-start button while
    the main switch (A) is turned on.
    3. The memory will now automatically
    be updated.
    4 . When the memory of the machine is correctly updated RESTART is indicated on the
    screen. Then...
    -Turn off the machine.
    -Remove the Floppy disk.
    5. Re-start the machine and check the revision (see above).
    NOTE! If the Main PC board is changed the memory always has to be updated with
    the latest version.
    Service Program 
    						
    							12104 72 47-26
    Upper rear cover
    1. Remove the five screws (A).
    2. Remove the two screws (B).
    3. Remove the screw (C).
    Lower rear cover
    1.Remove the  screw (D).
    2. Remove the lower rear cover pulling it backwards on the right-hand side and at the same
    time push the front covers upper and lower side of the free arm together.
    3. Remove the socket of the embroidery unit by bending it away from the snap in the in
     the cover with a screwdriver on the corner behind the socket.
    Covers 
    						
    							              13 104 72 47-26
    Front cover
    Dismounting
    1.  Dismount the rear covers.
    2.  Remove the button for the bobbin winding sensor stop, by pulling it straight out.
    3.  Remove the two screws (B) from behind.
    4.  Remove the two screws (C) in the base plate.
    5.  Turn the hand wheel until the needle is in its lowest position, so the thread take up lever
      is out of the way.
    6.  Carefully bend away the front cover from the hand wheel and pull it straight out.
         NOTE! Pull carefully the front cover away in order not to damage the cables.
    7.  Remove the cable (D) of theLCD transformer box and
         the cable(E) of the LCD .
    8.  Remove the band cable (G) of the touchpanel board
         from the circuit board by pulling the outer covering
         of the white switch outwards.
    9.  Remowe the cable (F) of the floppy disk drive
         from the circuit board by pulling the outer covering
         of the black switch outwards.
    10.  Remove the two cables (H) and (I)
         of the push button assembly .
    11. Remove the cable (K) of the thread tension.
    12 Remove the cable (M) of the lamp.
    13. Remove the earth cable from the LCD frame.
    Mounting
    Mount in reverse order
    Covers 
    						
    							14104 72 47-26
    Parts of the front cover
    LCD
    Dismounting
    1. Dismont the rear covers
    2. Dismount the front cover.
    3. Remove the LCD frame from the front cover by dismouning the 4 screws (A).
    4. Remove the LCD light cable (E)
    5. Remove the LCD  by dismounting the 4 screws (C).
    Mounting
    Mount in reverse order.
    Note! The black sealing should be on the the LCD.
    Touch Panel
    Can be removed after dismounting the LCD frame.
    Floppy disk drive
    Dismounting
    1. Dismont the rear covers
    2. Dismount the front cover.
    3. Remove the LCD  frame from the front cover by dismounting the 4 screws (A),
    4. Remove the transformer box by dismounting the screw (B).
    5. Remove the Floppy disk drive by dismount the 3 screws (D).
    6. Remove the cable from the floppy disk drive.
    Mounting
    Mount in reverse order.
    NOTE! When mounting the cable the contact area of the cable should be facing the floopy
    disk drive
    Covers 
    						
    							              15 104 72 47-26
    SETTINGS 
    						
    							16104 72 47-26
    1. The play of the hook gear
    It is impossible to obtain an equally large play in one rotation of the cog wheel, but it
    should be as small as possible at the tightest spot during the revolution.
    Check
    1. Rotate the hook back and forth and check the play.
    2. Do this check on at least 3 different spots during the revolution of the cog wheel.
       (Move the cog wheel with the hand wheel).
    Adjustment
    1. Loosen, screw (A) in the bearing clamp
    2. The play can now be adjusted by turning the eccentric bearing (C).
    NOTE! The hole (B) in the bearing shall always be on the lower half.
    Settings 
    						
    							              17 104 72 47-26
    2. Setting the hook in relation to the feeding eccentric
       (after feeding)
    Check
    1. The needle shall be in its centre position, straight stitching.
    2. Set the needle in its lowest turning postion.
    3. The tip of hook (A) shall now be centred behind the needle, and
         the tap of the worm gear should be positioned according to fig. 1.
    Note! The position of the pin shall be aligned with the frame opening.
    Adjustment
    1. Loosen screw (B). Remove the hook and set it into its correct position.
    Note! The position of the pin shall be aligned with the frame opening.
    Settings 
    						
    							18104 72 47-26
    3. Belt tension, arm/lower shaft belt
    1. Dismount rear cover and front cover.
    2. Dismount the bobbin winding device.
    3. Loosen the two screws (A) of the bearing clamps.
    4. The belt tension can now be adjusted by turning bearing (B) which is eccentric.
    NOTE! The hole (C) should always be on the front half.
    4. Belt tension, motor belt
    1. Dismount rear cover .
    2. Loosen the 2 screws (A) and adjust the belt tension by displacing the motor.
    NOTE! The adjustment of the arm/lower shaft belt affects this adjustment.
    Settings 
    						
    							              19 104 72 47-26
    5. Setting the feeding unit sideways
    Check
    1.  The distance A and B shall be equal between  the screw (C) and
      the edge of feeding device shaft (D).
    Adjustment
    1. Loosen the 2 screws  in the feeding device.
    2. Move the feeding device sideways until the distance A  and B  is equal between
        the screws (C) and the edge of feeding device shaft (D)
    3. Tighten the screws.
    Settings 
    						
    							20104 72 47-26
    Needle point
    6. Basic setting - the step motor of the needle
    Check
    1. Insert a new needle 90 in the machine.
    2. Set the needle in its upper turning position.
    3.The needle should always get to the centre position, when the main
       switch is turned on repeatedly.
    Check
    Get into the service program of the machine.
    The needle should be in its upper turning position.
    Touch Needle -
     , row 1.
    The needle should now take its centre position in the
    presser foot.
    Touch  Needle -
    , row 1.
    The needle shall now take its left position.
    The gap between the segment (A) and the calibration stop (B)
    should now be zero (0 mm).
    Note! The position of the eccentric.
    Settings 
    						
    All Husqvarna manuals Comments (0)

    Related Manuals for Husqvarna Designer 1 Service Manual