Hughes JVC Projector G1500m Unstructions Manual

19
ENGLISH
Connecting to Various Devices
The following signals can be input to the projector:
nVideo signals
(1) Response to color systems
*
1 : Responds if Y/C output is available.
*
2 : Signifies that component signals (ÒY, PB, PR Ó / Ò Y, B-Y, R-YÓ / ÒG, B, R, H/CS, VÓ) conform to the signal timing (synchroniza-
tion and video period) of each color system. The color systems are used for convenience only.
(2) Response to double density (*1), high-vision signals
Color system
NTSC NTSC4.43 PAL SECAMInput...

20
Memo
¥ When connecting a video device, use a TBC along with it, or one
which has a built-in TBC.
¥ Use of an extension cable to connect a video device and the
projector could cause video degradation.
¥ When a signal with much jitter is reproduced on a VCR or special-
effect playback is performed, the upper part of the picture or the
picture itself may be erased or distorted.
YAUDIO
AUDIO OUT
REMOTEY/C
VIDEO
Y
P
B/B-Y
P
R/R-Y L
R
RS-232C
Connecting to Various Devices (Cont.)
Connecting to Video...

21
ENGLISH
Before connection, be sure to turn off both the projector and other devices to be connected.
¥ Read the manual thoroughly which comes with the device to be connected.
¥ Speakers with a built-in amplifier and game devices can be connected. Use the AV connection cable and audio cable supplied,
or the cable supplied with a game device.
Connecting to Devices which Control the Projector
Before connection, be sure to turn off both the projector and devices to be connected.
¥ Read the manual...

22
Connecting to Various Devices (Cont.)
Connecting to Computer Devices
Before connection, be sure to turn off both the projector and computer devices.
¥ Read the manual which comes with each device thoroughly.
nConnection to an IBM PC or IBM-compatible computer
¥ Use the supplied computer connection cable. Also, prepare cables required for connecting the devices connected.
PC
AUDIOAUDIO
AUDIO
REMOTEY/C
L
R
H
V R
G
B
COMPUTER
OUT
RS-232C
POWER
¥ Desktop type
¥ Note type
¥ Desktop type
To monitor...

23
ENGLISH
Before connection, be sure to turn off both the projector and computer devices.
¥ Read the manual which comes with each device thoroughly.
nConnection to Macintosh
¥ Use the supplied Personal computer connection cable and the supplied conversion adapter for Mac.
Connecting to Computer Devices (Cont.)
¥ Desktop type
Connecting to Various Devices (Cont.)
PC
AUDIOAUDIO
AUDIO
REMOTEY/C
L
R
H/C
S
V R
G
B
COMPUTER
OUT
RS-232C
¥ When connecting an audio output terminal such as a computer sound
source...

24
Connecting to Various Devices (Cont.)
After all devices have finished being connected, connect the projectorÕs power cord. At this time, do not turn on the MAIN
POWER switch yet.
Power cord (supplied)
Lens cap
CAUTION
To prevent fire and electric shock, observe the following:
¥ When you do not use devices, pull out their power cords
from wall outlets.
¥ Do not connect the devices with power cords other than
supplied.
¥ Do not use voltage other than the power voltage indicated.
¥ Do not scar, damage,...

25
ENGLISH
When Turning On the Devices Connected to the Projector
Turn on the switches of the projector and the devices connected in the following order.
Skip over unconnected devices if there is any.
Power switch of the monitor of the computer which provides input to the projector
Peripheral devices of the computer which provides input to the projector
(Hard disk, magneto optical disk, scanner, etc.)
Power switch of AV devices which provide input to the projector
Projector itself
Power switches of...

26
Basic Operations
nProjectorÕs buttons
nRemote control unit
MAIN POWER switch
The following describes the basic procedure for normal use of
the projector.
1Turn on the MAIN POWER
switch.
ON [ y ]:The main power turns on and the STAND BY
indicator comes on.
Projector Õs indicator
2Press the OPERATE button.
(Or press the remote controlÕs
OPERATE button for one second
or more.)
¥ The OPERATE indicator comes on.
¥ About 30 seconds after the MAIN POWER switch is
turned on, you can start projecting.
Notes
¥...

27
ENGLISH
nRemote control unit
Basic Operations (Cont.)
nProjectorÕs buttons2. Select the video input to be projected
Remote control unit Projector
Screen display
* When the input is switched, the line display (ex. VIDEO) and
the source display (ex. NTSC(480i)) are shown on the upper
part of the screen (they disappear in about five seconds).
However, they will not be shown if LINE DISPLAY in ÒSetting
and Adjusting Other Functions (OPTIONS)Ó on page 43 is set
to OFF.
(For setting the source, see page...

28
Basic Operations (Cont.)
4. Adjust focus
nAdjust focus with the remote controlÕs FOCUS (+/Ð)
buttons.
nTo focus on farther points:
Press the FOCUS (+) button.
nTo focus on nearer points:
Press the FOCUS (Ð) button.
Remote control unit
Note
¥ Focus adjustment can also be made on the setting menu. For operating the
setting menu, refer to ÒMaking Basic SettingsÓ on page 31.
5. Adjust sound volume
nAdjust sound volume with the remote controlÕs VOL.
(+/Ð) buttons.
nWhen you press the VOL. (+) button:
The...