Huawei E352s 5 Manual

							 
 
 
 
Quick Start Guide  
						

							1 
Thank you for choosing the HUAWEI LTE E8372. The LTE 
E8372 provides high speed access to the wireless 
network.  Note: This guide briefly describes the appearance of the LTE E8372 and the steps for using the LTE E8372. For details about how to set the device and Wi-Fi management parameters, see help information on the device management web page at http://huawei.setup or http://192.168.8.1.  
						

							2 
Getting to Know Your LTE E8372 
The following figure shows the LTE E8372. The actual product may look different. 
 1
5
6
3
2
4  
						

							3 
 U S B  co n n ect o r 
Allows the LTE E8372 to connect to a computer or power adapter (not included). 
 Wi-F i  in d ica t o r 
Indicates the status of a Wi-Fi network.  
 Steady green: The Wi-Fi function is turned on.   Off: The Wi-Fi function is turned off or the LTE E8372 has been removed. 
 S M S  in d ica t o r 
Indicates the status of the SMS inbox. To view SMS messages and manage the inbox go to http://huawei.setup or http://192.168.8.1.  
 Steady green: There are unread messages in your inbox.  Blinking green once every 2 sec: The message storage is full.  Off: The LTE E8372 is powered off, there are no unread messages.     
						

							4 
 2 G/3G/LT E  in d i ca t o r 
Indicates the connection status to the Mobile network (connection to the internet).  Blinking green twice every 2 sec: The LTE E8372 is powered on.  Blinking green once every 0.2 sec: The software of the LTE E8372 is being upgraded.  Blinking green once every 2 sec: The LTE E8372 is registered with a 2G network.  Steady green: The LTE E8372 is connected to a 2G network.  Blinking blue once every 2 sec: The LTE E8372 is registered with a 3G network.  Steady blue: The LTE E8372 is connected to a 3G network.  Blinking cyan once every 2 sec: The LTE E8372 is registered with a LTE network.  Steady cyan: The LTE E8372 is connected to a 4G/LTE network.  Off: The LTE E8372 has been removed. 
 m i cr o S D card  s l ot 
microSD card holder for the LTE E8372.  
 S IM  ca rd  s lo t 
Subscriber Identity Module (SIM) card holder for the LTE E8372.  
						

							5 
Getting Started 
1.  Remove the cover from the LTE E8372 by sliding it off. Note: Make note of the SSID and Wi-Fi network key which are printed on the LTE E8372, as shown in the following diagram.    
  RESET
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx  
						

							6 
2.  Insert the SIM card and the microSD card (not included in package) into the corresponding card slot, as shown in the following figure.  3.  Replace the cover and slide it into place.  
  Note:   Ensure that the bevelled edge of the SIM card is properly aligned with that of the SIM card slot. 1
2
2
1  
						

							7 
 Do not remove the SIM card when the device is in use as it may get damaged and result in the data stored on the card becoming corrupted.  Please only use compatible SIM cards to avoid damage to your LTE E8372 and SIM card.   The microSD card is an optional accessory and is not included in the package.  Ensure that microSD card is inserted according to the direction (as labelled on the microSD card slot).  Do not remove the microSD when the device is in use as it may get damaged and result in the data stored on the card becoming corrupted.  
						

							8 
Con n ect i on  S cen a r i os 
Scenario 1: One-device Internet access using computer  
 
Scenario 2: Multi-device Internet access using Wi-Fi (connected to a computer)     
						

							9 
Scenario 3: Multi-device Internet access using Wi-Fi (connected to the power adapter)