Huawei B593 Manual

 
20 
Connecting the CPE 
Before you connect the CPE, read Warnings and Precautions carefully. 
 
Power off the CPE and remove all cables from the CPE in thunderstorms. 
Do not touch the external antenna of the CPE, which may be heated in use. 
 
Placing the CPE 
 Place  the  CPE  in  open environments. Otherwise, concrete  and  wooden  walls may 
affect the transmission of wireless signals. 
 Keep  the  CPE  away  from  the  household  electrical  appliances  that  produce  strong 
electric  or...

 
21 
 
 
  

 
22 
To connect devices to the CPE, do as follows: 
1.  Connect the CPE to the power. 
Connect the AC outlet of the power adapter to the POW ER port of the CPE. 
2.  Connect other devices to the CPE. 
 Connect LAN devices, such as computers or switches, to the LAN ports of the CPE by 
using cables. 
 Connect telephones or faxes to the TEL ports of the CPE by using telephone lines. 
3.  Start the CPE. 
Press the POW ER button to start the CPE. 
 
After the CPE is started, you can modulate the position...

 
23 
Configuration Requirements for the PC 
Your  PC  must  meet  the  following  requirements  for  configuring  the  CPE. Otherwise,  the 
operation performance may be degraded. 
Item Requirement 
CPU Pentium 500 MHz or higher 
Memory 128 MB RAM or higher 
Hard disk Available space of 50 MB 
Operating system Microsoft: W indows XP, W indows Vista, and W indows7 
Mac: Mac OS X 
Screen resolution 1024 x 768 pixels or higher 
Internet browser Internet  Explorer  7.0  or  later  versions,  Firefox  3.5 or...

 
24 
Accessing the Web-Based Utility 
The  Web-Based  Utility  of  the  CPE  is  a  web  browser-based  configuration  interface  that 
allows easy device setup, configuration and management through Internet browser. 
For example, to access the Web-Based Utility of the CPE from a PC that runs on W indows 
XP and uses IE 7.0, do as follows: 
1.  Ensure that the hardware of the CPE is connected correctly. 
2.  Set  the  IP  address  of  the  connected  computer  and  ensure  that  the  IP  address  of...

 
25 
 
By  default,  the  IP  address  of  the  CPE  is 192.168.1.1 and  the  subnet  mask  is 
255.255.255.0.  If  the  CPE  is  working  as  a  router,  it  is  recommended  that  the  IP 
address and DNS settings be obtained automatically. 
3.  Run the Internet Explorer, enter http://192.168.1.1 in the address bar and press Enter. 
4.  Enter  the  password  in  the  login  window  that  opens,  and  then  select Log In.  After  the 
password is verified, you can perform operations on the Web-Based...

 
26 
FAQ 
The power indicator is not on. 
 Check whether the power supply is properly connected. 
 Check whether the power adapter meets the requirements on specifications. 
Calls cannot get through. 
 Ensure  that  the  telephone  is  working  normally  and  the  telephone  line  is  connected 
correctly. 
 Ensure that the CPE works in LTE mode. Otherwise, the VoIP service cannot be used. 
 Ensure that the VoIP service is correctly configured in the Web-Based Utility. 
If the problem persists,...

 
27 
If the problem persists, contact the local service provider. 
The wireless network cannot be detected. 
 Check whether the power adapter is correctly connected. 
 Ensure  that  the  CPE  is  placed  in  open environments and  far  away  from  concrete  or 
wooden obstacles. 
 Keep the  CPE away  from  the  household  electrical  appliances  that  produce  strong 
electric  or magnetic  fields,  such  as  micro-wave  ovens,  refrigerators,  or  disc  satellite 
antennas. 
If the problem persists,...

 
28 
Specifications 
Wireless Network 
Standard FDD-LTE R8 2009Q4 
WCDMA/HSDPA R5/HSUPA R6/HSPA+ R7/DC-HSPA+ R8 
GSM/GPRS/EGPRS R99 
Frequency LTE: DD800, 900, 1800, 2100, 2600 
UMTS: 900, 2100 
GSM: 850, 900, 1800, 1900 
Port 
LAN Four Fast Ethernet (FE) ports 
TEL Two common telephone ports 
USB Two USB host ports 
SIM One SIM slot  

 
29 
Wi-Fi 
Standard IEEE 802.11b, IEEE 802.11g, IEEE 802.11n 
Others 
Ambient  temperature  for 
operation 
0˚C to 40˚C 
Relative  humidity  for 
operation 
5% to 95%, non-condensing 
Power adapter input 100 to 240 V AC, 50 Hz 
Power adapter output 12 V DC, 2 A 
Power consumption < 20 W 
Weight About 500 g 
Dimensions (L x W  x H) About 190 mm x 35 mm x 165 mm