Huawei B593 Manual

 
10 
 Norway: This subsection does not apply for the geographical area within a radius of 20 
km from the centre of Ny-Ålesund.  

 
11 
Thank You for Purchasing the LTE CPE! 
Generally, the LTE CPE will be replaced by the CPE in this guide. The following symbols are 
used in this guide: 
 A note provides additional information about a topic. 
 A tip provides an alternative method or shortcut to perform an action. 
 
A caution warns you about potential problems or specific precautions that need to 
be taken. 
 
 
Copyright Notification                                                                                    
 LTE is a...

 
12 
Before You Begin 
Check the following items in the product package: 
 LTE CPE B593 
 Power adapter 
 Ethernet cable 
 USB cable 
 Quick Start Guide 
 If you find anything missing or damaged, contact the vendor.   

 
13 
Getting to Know the CPE 
 The figures in this guide are provided only for reference, see the actual product for 
details. 
 
Exterior 
 
   

 
14 
1 POWER indicator 2 WLAN indicator 3 WPS indicator 
4 TEL indicator 5 MODE indicator 6 SIGNAL indicator 
7 SIM card slot 8 POWER button 9 USB host 
10 POWER port 11 USB port 12 TEL ports 
13 LAN ports 14 LAN indicators 15 WPS button 
16 RESET button 17 WLAN button   
 
Indicator 
The  CPE provides  indicators  on  the  front  and rear panels.  The  following  table 
describes the states of each indicator.  
Indicator State Description 
POWER On The CPE is powered on. 
Only when the POW ER indicator...

 
15 
Indicator State Description 
Off The CPE is powered off. 
TEL1/TEL2 On This  indicator  is  on  when  the  CPE  of  the  calling  or  called party is in off-hook state. 
Blinking This  indicator  blinks  when  the  CPE  is  not  switched  to the off-hook state during a call. 
Off This indicator is off when the CPE is hooked off and there is no calling party. 
MODE Blue This  indicator  is constantly blue  when  the  CPE  has accessed the LTE network but no data is transferred. 
This indicator is...

 
16 
Indicator State Description 
Red This  indicator  is constantly red  when  the  CPE  fails  to access  the  wireless  network or  the  CPE  does  not  access the wireless network. 
Mulberry This indicator is on when the SIM cannot be identified or the PIN is not entered or the PIN check fails. 
Off This  indicator  is  off  when  the  CPE  does  not  access  the wireless network. 
WLAN On The W LAN function is enabled. 
Blinking This  indicator  is  blinking  when data  is transferred through the W...

 
17 
Indicator State Description 
WPS Regular blinking Authentication  for  W PS  accessing  is  implementing.  The indicator blinks not more than two minutes. 
Irregular blinking An event or alarm occurs. You need to log in to the W EB UI and perform related operations. 
On The W PS function is enabled. 
Off The W PS function is disabled. 
All  indicators except  the POWER indicator 
Blinking The CPE is performing an update configuration, such as an upgrade  or  resetting.  In  this  period, to...

 
18 
 
Ports and Buttons 
Item Description 
POWER This port is for connecting to a power adapter. 
TEL1/TEL2 These ports are connecting to telephones or faxes (optional). 
LAN1–LAN4 These ports are for  connecting  to computers,  switches,  or  other  LAN 
devices. 
RESET  You  can  restart  the  CPE  by  holding  down  this  button  for  2 to 5 
seconds. 
 You can restore the default settings of the CPE by holding down this 
button for more than 5 seconds. 
Restoring  the  default  settings  of  the...

 
19 
Item Description 
 You  can  enable  the Wi-Fi  function by  holding  down  this  button  for 
more than 3 seconds. 
WPS This is the W PS switch. 
SIM This slot is for inserting the SIM. 
USB This port is for inserting the USB device. 
 This port is not for connecting the USB host device, such as a PC.