HP Zr2040w User Guide

CAUTION:The HP Quick Release 2 can be installed directly to a wall to mount the monitor panel. It
is designed to support a maximum of up to 10.9 kg (24 lbs). If you are mounting to a wall, HP
recommends that you consult with a qualified engineering, architectural, or construction professional
to determine the appropriate type and quantity of mounting fasteners required for your application
and to ensure that the mounting solution is properly installed to support applied loads.
The weight for your model...

Mounting a Quick-Release Panel
The ZR2240w, ZR2440w and ZR2740w support mounting to VESA-compliant hardware in two ways:
●Remove the HP stand and use the 4 VESA mount threaded holes (100 x 100 pattern) that are in
the Quick Release 2 recess. Screws of the appropriate length are provided.
Figure 2-13  Mounting a VESA Arm
●Alternatively, follow the instructions below to use the HP Quick Release 2 feature with your
VESA mounting hardware.
Start by removing the pedestal.
Figure 2-14  Removing the Pedestal...

3.Slide the pedestal out of the recess.
4.Remove four screws holding the mounting plate to the head of the pedestal:
Figure 2-15  Removing the Mounting Plate from the Pedestal
5.Remove four screws to separate the mounting plate from its cover:
Figure 2-16  Removing the Cover from the Mounting Plate
Mounting the Monitor to User-Supplied Support Hardware 17
 

6.Attach the mounting plate to the wall or swing arm of your choice.
Figure 2-17  Installing the Mounting Plate
CAUTION:This monitor supports the VESA industry standard 100 mm mounting holes. To
attach a third-party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long
screws are required. Longer screws must not be used because they may damage the monitor. It
is important to verify that the manufacturer’s mounting solution is compliant with the VESA
standard and is rated to support the...

Identifying information is located on the pull-out card (instead of on labels on the back of the monitor).
Warranty support information (model number, serial number, product number) is printed on the front
of the card and regulatory information is printed on the back of the card.
Installing a Cable Lock
You can secure the monitor to a fixed object with an optional cable lock available from HP.
Figure 2-19  Installing a Cable Lock
Turning on the Monitor
1.If your monitor has a master power switch (located...

Adjusting the Monitor
1.Tilt the monitors panel forward or backward to set it to a comfortable eye level.
Figure 2-20  Adjusting the Tilt
2.If your monitor has the ability to swivel, adjust it to the left or right for the best viewing angle.
Figure 2-21  Adjusting the Viewing Angle (Select Models)
3.Models ZR2240w, ZR2440w, and ZR2740w provide for height adjustment. Adjust the monitors
height so that it is parallel to your eye height for a comfortable viewing position. A lock-down/
release button on the...

monitor is lifted. If the display head is locked in the lowest position, release and adjust it as
follows:
Figure 2-22  Adjusting the Height (Select Models)
a.Make sure that the monitor is safely positioned on a stable surface.
b.Gently push down on the display head (1).
c.While pushing down the display head, press the lock-down/release button on the back of
the column (2).
d.Guide the display head up to the desired height (3).
4.The default orientation of the monitor is landscape. If you want to change...

Portrait Orientation
The ZR2040w must be mounted in the orientation you wish to use. Other models can be pivoted after
mounting. To do this, raise the panel to its highest position and pivot it clockwise from landscape to
portrait.
Figure 2-23  Pivoting the Monitor (Select Models)
NOTE:It may be necessary to tilt the monitor panel back to prevent the corner of the panel from
coming in contact with the base when pivoting.
If your model is a ZR2740w, rotate the image using the workstation video driver...

3 Operating the Monitor
Overview of Operation
If you are not familiar with HP Performance monitors, read this section for an overview of how they
operate. This will help you locate specific information elsewhere in this manual.
Your monitor provides for more than one source of input. It will scan the various inputs to find an
active one and display that image. You can change sources manually, using the SOURCE button on
the front panel. The scanning order is initially set to DisplayPort, DVI-D, HDMI, VGA,...

through the OSD. Pressing the + button on the front of the monitor will take you directly to the OSD
source-control submenu.
Figure 3-1  ZR2040w and ZR2240w Front Panel Controls
Control Function
1
Menu Opens, selects or exits the OSD menu.
2
Minus If the OSD menu is on, press to navigate backward through
the OSD menu and decrease adjustment levels.
If the OSD menu is inactive, resets OSD choices to their
factory defaults, ZR2040w model only.
3
Plus/source If the OSD menu is on, press to navigate forward...