HP Zr2040w User Guide

2 Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other
attached devices, then follow the instructions below.
NOTE:Be sure the master power switch, located on the rear panel of the monitor, is in the off
position. The master power switch turns off all power to the monitor.
Installing the Pedestal
NOTE:Do not install the pedestal if the monitor will be used on a wall, swing arm, or other mounting
fixture; instead see 
Mounting the...

Models ZR2240w, ZR2440w, and ZR2740w use the HP Quick Release 2 mechanism for easy moving
of the monitor. To mount the panel onto the pedestal:
1.Slide the mounting plate on the pedestal under the upper lip of the recess in the back of the
panel.
2.Lower the pedestal into the recess until it snaps into place.
3.The HP Quick Release 2 latch pops up when the monitor is locked in place.
Figure 2-2  Mounting the Panel onto the HP Quick Release 2
Rear Components
ZR2040w Model
Figure 2-3  ZR2040w Rear...

ZR2240w Model
Figure 2-4  ZR2240w Rear Components
221232425262789
1111
1010
Component Function
1 Cable Lock Provision Provides slot for use with cable security locks.
2 Master Power Switch Turns off all power to the monitor.
NOTE:Putting the switch in the Off position will yield the
lowest power state for the monitor when not in use.
3 AC Power Connector Connects the AC power cord to the monitor.
4 DisplayPort Connector Connects the DisplayPort cable to the monitor.
5 HDMI Connector Connects an HDMI...

Component Function
10 Information Card Provides information needed for a support call.
11 USB Downstream Connectors
(side panel)Connects optional USB devices to the monitor.
ZR2440w Model
Figure 2-5  ZR2440w Rear Components
Component Function
1 Cable Lock Provision Provides slot for use with cable security locks.
2 Master Power Switch Turns off all power to the monitor.
NOTE:Putting the switch in the Off position will yield the
lowest power state for the monitor when not in use.
3 AC Power Connector...

Component Function
5 Analog Audio Output Connects an audio cable with 3.5 mm L/R mini-plug to the
monitor.
6 DisplayPort Connector Connects the DisplayPort cable to the monitor.
7 HDMI Connector Connects an HDMI cable to the monitor.
8 DVI-D Connector Connects the DVI-D cable to the monitor.
9 USB Upstream Connector Connects the monitor USB hub cable to a host USB port/
hub.
10 USB Downstream Connectors Connects optional USB devices to the monitor.
11 Information Card Provides information about the...

ZR2740w Model
Figure 2-6  ZR2740w Rear Components
Component Function
1 Cable Lock Provision Provides slot for use with cable security locks.
2 Master Power Switch Turns off all power to the monitor.
NOTE:Putting the switch in the Off position will yield the
lowest power state for the monitor when not in use.
3 AC Power Connector Connects the AC power cord to the monitor.
4 DisplayPort Connector Connects the DisplayPort cable to the monitor.
5 DVI-D Connector Connects the DVI-D cable to the monitor.
6 USB...

Routing and Connecting the Cables
Place the monitor in a convenient, well-ventilated location near the computer.
ZR2040w Model
The cable-restraining bar on the pedestal of the ZR2040w is held in place by four tabs.
Figure 2-7  Cable-Restraining Bar
1.To remove the bar, first pull one end of the bar away from the pedestal (1). When it is free, the
bar can be removed (2).
2.Connect the video cables provided to the connectors shown in ZR2040w Model on page 6. You
do not have to connect them all.
3.For each...

4.Connect the AC power cord and plug it into the wall outlet.
WARNING!To reduce the risk of electric shock or damage to the equipment:
Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
For your safety, do not place anything on power cords or cables. Arrange them so...

ZR2240w, ZR2440w, and ZR2740w Models
1.Remove the cable routing cover by pulling it straight off the front of the column.
Figure 2-9  Cable Routing Cover
2.Before connecting the cables, route them through the cable routing hole in the column (1) and
replace the cable routing cover (2).
Figure 2-10  Cable Routing
Routing and Connecting the Cables 13
 

3.Connect the desired signal sources. Refer to the drawings in (Rear Components on page 6) to
identify the connectors on your monitor. For each one, plug in one end of the appropriate cable.
Attach the other end to your computer or other video source.
The ZR2440w model supports audio output from the HDMI and DisplayPort inputs. Use the RCA
jack for digital output and the 3.5 mm mini-jack for analog 2.0 Sound.
NOTE:It is not necessary to connect all the connectors to video sources.
4.If you will be using...