HP PhotoSmart C5283 User Manual

4.Lower the CD/DVD access door to access the CD/DVD tray.
The CD/DVD access door is located just below  the control panel. When in its lowered
position, the CD/DVD tray sits on top of the output tray.
5. Push the CD/DVD holder into the HP All-in-One until the lines on the CD/DVD holder
line up to the white lines on the CD/DVD tray.
NOTE: The HP All-in-One pulls the CD/DVD holder while printing on the media.
The CD/DVD holder might protrude about 7.5 cm (3 inches) at the back of the
device. If the HP...

1xD-Picture Card
2Memory Stick, Memory Stick Pro, Memory Stick Select, Me mory Stick Magic Gate, Memory
Stick Duo or Duo Pro (adapter optional), or Memory Stick Micro (adapter required)
3CompactFlash (CF) types I and II
4Secure Digital (SD), Secure Digital Mini (adapter required), Secure Digital High Capacity
(SDHC), MultiMediaCard (MMC), MMC Plus, MMC Mobile (RS-MMC; adapter required),
TransFlash MicroSD Card, or Secure MultiMedia Card
To view and select photos
1. Insert a memory card into the...

9.(Optional) If you want to check and/or modify any of your print settings, press  to
highlight  Settings and press  OK.
10. To print the photo(s), use 
 or  to highlight  Print Now (or press the  Print Photos
button on the control panel).
A print status screen displays the number of pages to print and the estimated time to
complete.
Scan an image
You can start a scan from your computer or from the control panel of the HP All-in-One.
This section explains how to scan from the control panel of the HP...

To make a copy from the control panel
1.Make sure you have paper loaded in the input tray.
2. Load your original print side down on the right front corner of the glass.
3. Press  Start Copy Black  or Start Copy Color  to begin copying.
Replace the print cartridges
Follow these instructions when you need to replace print cartridges.
NOTE:When the ink level for the print cartridge is low, a message appears on the
display. You can also check the ink levels by using the  Printer Toolbox available
through...

If you are replacing the black, photo, or gray photo print cartridge, remove the print
cartridge from the slot on the right.
1Print cartridge slot for the tri-color print cartridge
2Print cartridge slot for the black and photo print cartridges
4.Pull the print cartridge toward you out of its slot.
5. If you are removing the black print cartridge in order to install the photo or gray photo
print cartridge, store the black print cartridge in the print cartridge protector or an
airtight plastic container....

7.Hold the print cartridge with the HP logo on top, and insert the new print cartridge into
the empty cartridge slot. Make sure you push the print cartridge in firmly until it snaps
into place.
If you are installing the tri-color print cartridge, slide it into the left slot.
If you are installing a black, photo, or gray photo print cartridge, slide it into the right
slot.
8.Close the print cartridge door.
If you installed a new print cartridge, the HP All-in-One prints a print cartridge
alignment page....

10.The HP All-in-One prints a test page, aligns the print head, and calibrates the printer.
Recycle or discard the page.
A success or failure message appears.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
If the alignment fails again, you might have a defective sensor or print cartridge.
Contact HP Support. Go to 
www.hp.com/support . If prompted,...

3.Dry the backing with a dry, soft, lint-free cloth.
CAUTION: Do not use paper-based wipes, as these might scratch the backing.
4.If further cleaning is needed, repeat the  previous steps using isopropyl (rubbing)
alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual
alcohol.
CAUTION: Be careful not to spill alcohol on the glass or exterior of the HP All-
in-One, as this might damage the device.
5. Plug in the power cord, and then turn on the HP All-in-One.
Chapter 1
16 HP...

2 Troubleshooting and support
This chapter contains troubleshooting information for the HP All-in-One. Specific information is
provided for installation and configuration i ssues, and some operational topics. For more
troubleshooting information,  see the onscreen Help that came with your software.
Many issues are caused when the  HP All-in-One is connected to the computer using a USB cable
before the HP All-in-One software is installed on  the computer. If you connected the HP All-in-One
to your...

Solution
•Make sure the power cord is firmly connected to both the HP All-in-One and the power
adapter. Plug the power cord into a power outlet, surge protector, or power strip.
1Power connection
2Power cord and adapter
3Power outlet
•If you are using a power strip, make sure t he power strip is on. Or, try plugging the HP All-
in-One directly into a power outlet.
• Test the power outlet to make sure it is working. Plug in an appliance that you know works,
and see if the appliance has power. If not,...