HP PhotoSmart C5183 User Manual

Connect the HP All-in-One to the network
An Ethernet port is provided on the back of the HP All-in-One.
To connect the HP All- in-One to the network
1. Remove the yellow plug from the back of the HP All-in-One.
2. Connect the Ethernet cable to the Ethernet port on the back of the HP All-in-One.
3. Connect the other end of the Ethernet c able to an available port on your Ethernet
router or switch.
4. Once you have connected the HP All-in-One to the network, install the software.
Install the software for a...

To install the Windows HP All-in-One software
1. Quit all applications running on your computer, and any firewall or virus detectionsoftware.
2. Insert the Windows CD that came with the HP All-in-One into the CD-ROM drive on your computer and follow the onscreen instructions.
3. If a dialog box pertaining to firewalls appears, respond as follows:
–The  Issues Stopping Installation  screen means that a firewall or anti-spyware
program might be running that could interfere with the HP Software...

6. Follow the onscreen instructions to complete all the installation steps, includingthe Setup Assistant .
When you have finished installing the software, the HP All-in-One is ready for use.
7. To test your network connection, go to your Mac and print a self-test report to the
HP All-in-One.
Load originals and load paper
You can copy or scan up to letter- or A4-size originals by loading them on the glass.
To load an original on the glass
1. Lift the lid on the HP All-in-One.
2. Load your original print...

3. Insert the stack of paper into the input tray with the short edge forward and the printside down. Slide the stack of paper forward until it stops.
Tip If you are using letterhead, insert the top of the page first with the print
side down. For more help on loading full-size paper and letterhead, refer to
the diagram engraved in the base of the input tray.
4. Slide the paper-width and paper-length guides inward until they stop at the edges
of the paper.
Do not overload the input tray; make sure the...

To load 10 x 15 cm (4 x 6 inch) photo paper in the photo tray
1. Raise the output tray, and then pull out the photo tray.
2. Insert the stack of photo paper into the photo tray with the short edge forward andthe print side down. Slide the stack of photo paper forward until it stops.
If the photo paper you are using has perforated tabs, load the photo paper so that
the tabs are closest to you.
3. Slide the paper-length and paper-width guides inward against the stack of photo
paper until the guides stop....

To make a copy from the control panel
1. Make sure you have paper loaded in the input tray.
2. Load your original print side down in the right front corner of the glass.
3. Press Start Copy Black  or Start Copy Color  to begin copying.
Scan an image
You can start a scan from your computer or from the HP All-in-One. This section explains
how to scan from the control panel of the HP All-in-One only.
To use the scan features, the HP All-in-One and computer must be connected and turned
on. The HP Photosmart...

b. Press  or  to highlight a paper size, and then press OK.
The paper size choices available vary depending on your country/region.
Note Depending on the paper size you choose, you might be prompted
to choose a layout for the photos on your pages.
c. When the  Fix Faded Original?  prompt appears, highlight  Yes or No as
appropriate, and then press  OK.
The HP All-in-One scans your original  and shows a preview of the photo on the
display.
d. Press  OK to display the selection menu.
Tip If you want to...

b. Press OK to select the default computer, or press  to select a different
computer, and then press  OK.
The  Scan To  menu appears on the display, listing the applications on the
selected computer.
If the HP All-in-One is connected directly to a computer with a USB cable, proceed
to step 5.
5. Press  OK to select the default application to receive the scan, or press 
 to select
a different application, and then press  OK.
A preview image of the scan appears on  your computer, where you can edit it.
6....

–Bottom left : xD-Picture Card
– Bottom right : Memory Stick, Magi c Gate Memory Stick, Memory Stick Duo
(with user-supplied adapter), Memory Stick Pro
2. Press  OK to select  View & Print .
When you press  OK, the most recent photo on your memory card appears on the
display.
3. Press 
 or  to scroll through the photos on your memory card.
4. When the photo you want to print appears, press  OK.
Tip If you want to print the photo using the default print settings, press  Print
Photos . The HP All-in-One...

To print from a software application (Windows)
1. Make sure you have paper loaded in the input tray.
2. On the File menu in your software application, click  Print.
3. Select the HP All-in-One as the printer. If you set the HP All-in-One as the default printer, you can skip this step. The HP All-
in-One will already be selected.
4. If you need to change settings, click the button that opens the  Properties dialog
box.
Depending on your software application, this button might be called  Properties,...