HP Pavilion M6 1000 Entertainment Notebook Pc Series User Guide

							6 Managing power
Your computer can operate on either battery power or external power. When the computer is only
running on battery power and an AC power source is not available to charge the battery, it is
important to monitor and conserve the battery charge. Your computer supports power plans to
manage how your computer uses and conserves power so that you can balance computer
performance with power conservation.
Using Sleep or Hibernation
Microsoft Windows has two power-saving states, Sleep and Hibernation.
NOTE:For select models, the Intel Rapid Start Technology (RST) feature is enabled at the factory.
Rapid Start Technology allows your computer to resume quickly from inactivity.
Rapid Start Technology manages your power-saving options as follows:
●Sleep—Rapid Start Technology allows you to select the Sleep state. To exit from Sleep, press
any key, activate the TouchPad, or press the power button briefly.
●Hibernation—Rapid Start Technology initiates Hibernation under the following conditions:
◦After 2 hours of inactivity when the computer is running on battery or external power.
◦When the battery reaches a critical level.
After Hibernation is initiated, press the power button to resume your work.
Rapid Start Technology can be disabled in Setup Utility (BIOS).
When Sleep is initiated, the screen clears, and your work is saved to memory, allowing you to resume
your work faster than when you exit Hibernation. If the computer is in the Sleep state for an extended
period or if the battery reaches a critical battery level while in the Sleep state, the computer initiates
Hibernation.
In the Hibernation state, your work is saved to a hibernation file on the hard drive and the computer
turns off.
CAUTION:To reduce the risk of possible audio and video degradation, loss of audio or video
playback functionality, or loss of information, do not initiate Sleep or Hibernation while reading from or
writing to a disc or an external media card.
NOTE:You cannot initiate any type of networking connection or perform any computer functions
while the computer is in the Sleep state or in Hibernation.
Using Sleep or Hibernation 41 
						

							Initiating and exiting Sleep
The system is set at the factory to initiate Sleep after a specific period of inactivity, depending on
whether the computer is running on battery power or on external power.
Power settings and timeouts can be changed using Power Options in Windows Control Panel.
With the computer on, you can initiate Sleep in any of the following ways:
●Briefly press the power button.
●Close the display.
●Select Start, click the arrow next to the Shut down button, and then click Sleep.
To exit Sleep:
●Briefly press the power button.
●If the display is closed, open the display.
●Press a key on the keyboard.
●Tap or swipe the TouchPad.
When the computer exits Sleep, the power lights turn on and the computer displays the screen as it
was when you stopped working.
NOTE:If you have set the computer to require a password on wakeup, you must enter your
Windows password before the computer redisplays your work.
Initiating and exiting Hibernation
The system is set at the factory to initiate Hibernation after a specific period of inactivity, depending
on whether the computer is running on battery power or on external power, or when the battery
reaches a critical battery level.
Power settings and timeouts can be changed in Windows Control Panel.
To initiate Hibernation, select Start, click the arrow next to the Shut down button, and then click
Hibernate.
To exit Hibernation, briefly press the power button.
The power lights turn on and the computer returns to the screen where you stopped working.
NOTE:If you have set a password to be required on wakeup, you must enter your Windows
password before the computer will return to the screen.
Setting password protection on wakeup
To set the computer to prompt for a password when exiting Sleep or Hibernation, follow these steps:
1.Select Start > Control Panel > System and Security > Power Options.
2.In the left pane, click Require a password on wakeup.
3.Click Change Settings that are currently unavailable.
42 Chapter 6   Managing power 
						

							4.Click Require a password (recommended).
NOTE:If you need to create a user account password or change your current user account
password, click Create or change your user account password, and then follow the on-
screen instructions.
5.Click Save changes.
Using the power meter
The power meter allows you to quickly access power settings and view the remaining battery charge.
●To display the percentage of remaining battery charge and the current power plan, move the
pointer over the Power Meter icon, at the far right of the taskbar.
●To access Power Options, or to change the power plan, click the Power Meter icon and select
an item from the list.
Different power meter icons indicate whether the computer is running on battery or external power.
The battery icon displays a message if the battery reaches a low or critical battery level.
Selecting a power plan
A power plan manages how the computer uses power and helps you conserve power and maximize
performance.
The following power plans are available:
●HP Recommended. Automatically balances performance with energy conservation.
●Power Saver. Saves power by reducing system performance and screen brightness.
●High Performance. Favors performance, but may use more energy.
You can also create your own power plan and customize it to suit your needs.
Use HP Power Manager (select models only) or Windows Control Panel to select a power plan or to
create your own plan.
To start HP Power Manager, select Start > Control Panel > Hardware and Sound > HP Power
Manager.
To access the Power Options in the Control Panel, select Start > Control Panel > System and
Security > Power Options, and then select a power plan from the list.
Using the power meter 43 
						

							Running on battery power
When a charged battery is in the computer and the computer is not plugged into external power, the
computer runs on battery power and the display brightness decreases to conserve battery life. The
battery in the computer slowly discharges when the computer is off and unplugged from external
power.
Computer battery life varies, depending on power management settings, programs running on the
computer, display brightness, external devices connected to the computer, and other factors.
Removing a user-replaceable battery
Your computer includes a user-replaceable battery.
WARNING!To reduce potential safety issues, use only the user-replaceable battery provided with
the computer, a replacement battery provided by HP, or a compatible battery purchased from HP.
CAUTION:Removing a battery that is the sole power source for the computer can cause loss of
information. So before removing the battery, save your work and initiate Hibernation, or shut down the
computer through Windows.
To remove the battery:
1.Turn the computer upside down on a flat surface.
2.Slide the battery release latch (1) to release the battery.
NOTE:The battery release latch automatically returns to its original position.
3.Pivot the battery (2) upward and remove it from the computer (3).
44 Chapter 6   Managing power 
						

							Finding battery information
Help and Support provides the following tools and information about the battery:
●Battery Check tool in Help and Support to test battery performance
●Information about calibration, power management, and proper care and storage to maximize
battery life
●Information about battery types, specifications, life cycles, and capacity
To access battery information, select Start > Help and Support > Learn > Power Plans:
Frequently Asked Questions.
Conserving battery power
Use the following tips for conserving battery power and maximizing battery life:
●Lower the brightness on the display.
●Select the Power saver setting in Power Options.
●Remove the battery from the computer when it is not being used or charged.
●Turn off wireless devices when you are not using them.
●Disconnect unused external devices that are not plugged into an external power source, such as
an external hard drive connected to a USB port.
●Stop, disable, or remove any external media cards that you are not using.
●Before you leave your computer, initiate Sleep or Hibernation, or shut down the computer.
Identifying low battery levels
When a battery that is the sole power source for the computer reaches a low or critical battery level,
the power meter icon in the notification area displays a low or critical battery notification.
NOTE:For additional information about the power meter, see Using the power meter on page 43.
The computer takes the following actions for a critical battery level:
●If Hibernation is enabled and the computer is on or in the Sleep state, the computer initiates
Hibernation.
●If Hibernation is disabled, and the computer is on or in the Sleep state, the computer remains
briefly in the Sleep state, and then shuts down and loses any unsaved information.
Storing a user-replaceable battery
CAUTION:To reduce the risk of damage to a battery, do not expose it to high temperatures for
extended periods of time.
If your computer will be unused and unplugged from external power for more than 2 weeks, remove
the battery and store it separately in a cool, dry place to prolong the battery charge.
A stored battery should be checked every 6 months. If the capacity is less than 50 percent, recharge
the battery before returning it to storage.
Running on battery power 45 
						

							Disposing of a user-replaceable battery
WARNING!To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short
external contacts; do not dispose of in fire or water.
See the Regulatory, Safety and Environmental Notices for proper battery disposal. To access this
guide, select Start > Help and Support > User Guides.
Replacing a user-replaceable battery
Battery Check in Help and Support notifies you to replace the battery when an internal cell is not
charging properly or when the battery storage capacity has reached a weak condition. If the battery is
possibly covered by an HP warranty, instructions include a warranty ID. A message refers you to the
HP website for more information about ordering a replacement battery.
Running on external power
For information about connecting to AC power, see the Setup Instructions provided in the computer
box.
The computer does not use battery power when the computer is connected to external power with an
approved AC adapter or an optional docking/expansion device.
WARNING!To reduce potential safety issues, use only the AC adapter provided with the computer,
a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP.
Connect the computer to external power under any of the following conditions:
WARNING!Do not charge the computer battery while you are onboard an aircraft.
●When charging or calibrating a battery
●When installing or modifying system software
●When writing information to a disc (select models only)
●When running Disk Defragmenter on computers with internal hard drives
●When performing a backup or recovery
When you connect the computer to external power:
●The battery begins to charge.
●The display brightness increases.
●The Power Meter icon in the notification area changes appearance.
When you disconnect external power, the following events occur:
●The computer switches to battery power.
●The display brightness automatically decreases to save battery life.
●The Power Meter icon in the notification area changes appearance.
46 Chapter 6   Managing power 
						

							HP CoolSense
HP CoolSense  automatically detects when the computer is not in a stationary position and
adjusts performance and fan settings to keep the surface temperature of your computer at the
optimum level of comfort.
When HP CoolSense is off, the position of the computer is not detected and the performance and fan
options remain at the factory setting. As a result, the surface temperature of the computer may be
higher than it would be with HP CoolSense on.
To turn CoolSense off or on, follow these steps:
1.Select Start > Control Panel > Hardware and Sound > HP CoolSense.
2.Select On or Off.
Refreshing your software content with Intel Smart
Connect Technology (select models only)
When the computer is in the Sleep state, Intel® Smart Connect Technology periodically causes the
computer to exit Sleep. Smart Connect then updates the content for certain open applications and
reinitiates Sleep. As a result, your work is immediately available to you as soon as you exit Sleep.
You do not have to wait while updates are downloaded.
▲To enable this feature or manually adjust the settings, select Start > All Programs > Intel >
Intel Smart Connect Technology.
For additional information and a list of supported applications, see the software Help.
Shutting down the computer
CAUTION:Unsaved information is lost when the computer shuts down.
The Shut down command closes all open programs, including the operating system, and then turns
off the display and computer.
Shut down the computer under any of the following conditions:
●When you need to replace the battery or access components inside the computer
●When you are connecting an external hardware device that does not connect to a USB or video
port
●When the computer will be unused and disconnected from external power for an extended
period
Although you can shut down the computer with the power button, the recommended procedure is to
use the Windows Shut down command:
NOTE:If the computer is in the Sleep state or in Hibernation, you must first exit Sleep or
Hibernation before shutdown is possible.
1.Save your work and close all open programs.
2.Select Start > Shut down.
HP CoolSense 47 
						

							If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try
the following emergency procedures in the sequence provided:
●Press ctrl+alt+delete, and then click the Shut down icon on the display.
●Press and hold the power button for at least 5 seconds.
●Disconnect the computer from external power.
●On models with a user-replaceable battery, remove the battery.
48 Chapter 6   Managing power 
						

							7 Managing and sharing information
Drives are digital storage devices or solid-state drives that help you store, manage, share, and
access information. Your computer has an internal hard drive that stores your computers software,
operating system, as well as providing storage for all of your personal files. Some computers also
have a built-in optical drive that allows you to read or write to a CD, DVD, or (on select models) Blu-
ray Disc (BD), to play and record audio and video.
For added capacity or functionality, connect an external drive (purchased separately), such as an
optical drive or hard drive, or insert a digital storage card to import information directly from your
phone or camera. A Universal Serial Bus (USB) flash drive, connected to the Universal Serial Bus
(USB) port on your computer, also allows quick data transfer. Some devices use the computers
power to run; others have their own power source. Some devices come with software that must be
installed.
NOTE:For information about connecting external wireless devices, see Connecting to a network
on page 17.
NOTE:For more information about required software and drivers, or to learn which computer port to
use, see the manufacturers instructions.
Using a USB device
Most computers have more than one USB port, because this versatile interface allows you to connect
to numerous kinds of external devices to your computer, such as a USB keyboard, mouse, external
drive, printer, scanner, or USB hub.
Your computer may have more than one type of USB port. See 
Getting to know your computer
on page 4 for the types of USB ports you have on this computer. Be sure to purchase devices that
are compatible with your computer.
Type Description
USB 2.0 Transfers data at 60 MB/s.
USB 3.0 Transfers data at 640 MB/s. USB 3.0 ports, also known as
SuperSpeed ports, are also compatible with USB 1.0 and 2.0
devices.
NOTE:A powered/charging USB port allows certain USB devices to charge while they are plugged
into this port. Standard USB ports will not charge all USB devices or will charge using a low current.
In addition, some USB devices cannot operate unless they are connected to a powered port.
Using a USB device 49 
						

							Connecting a USB device
CAUTION:To reduce the risk of damage to a USB connector, use minimal force to connect the
device.
▲Connect the USB cable for the device to the USB port.
NOTE:The USB port on your computer may look slightly different from the illustration in this
section.
A sound indicates that the device has been detected.
NOTE:The first time you connect a USB device, a message in the notification area lets you know
that the device is recognized by the computer.
Removing a USB device
CAUTION:To reduce the risk of damage to a USB connector, do not pull on the cable to remove
the USB device.
CAUTION:To reduce the risk of loss of information or an unresponsive system, use the following
procedure to safely remove the USB device.
1. To remove a USB device, save your information and close all programs associated with the device.
2. Click the remove hardware icon in the notification area, at the far right of the taskbar, and then
follow the on-screen instructions.
3. Remove the device.
Connecting a powered USB device
CAUTION:To reduce the risk of damage to the equipment when connecting a powered device, be
sure that the device is turned off and its AC power cord is unplugged.
1.Connect the device to the computer.
2.Plug the device power cord into a grounded AC outlet.
3.Turn on the device.
50 Chapter 7   Managing and sharing information