HP Pavilion Dv7 3100 Entertainment Notebook Pc Series Manual

							Removal and replacement procedures
Maintenance and Service Guide4–45
3. Remove the assembly 3 from the base enclosure.
Reverse this procedure to install the modem module cable.
Power connector cable
✎The power connector cable is also available in the Cable Kit, spare part number 516328-001.
Before removing the power connector cable, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6). 
5. Remove the following components: 
a. Optical drive (see “Optical drive” on page 4-7) 
b. Hard drive (see “Hard drive” on page 4-11)
c. TV tuner module (see “TV tuner module” on page 4-18)
d. Switch cover and keyboard (see “Switch cover and keyboard” on page 4-19)
e. Speaker assembly (see “Speaker assembly” on page 4-23)
f. Display assembly (see “Display assembly” on page 4-25)
g. Top cover (see “Top cover” on page 4-34)
h. System board (see “System board” on page 4-37)
i. USB board (see “USB board” on page 4-41)
Remove the power connector cable: 
1. Remove the Phillips PM2.5×7.0 screw 1 that secures the power connector and bracket 2 to the base enclosure.
Description Spare part number 
Power connector cable 538085-001  
						

							4–46Maintenance and Service Guide
Removal and replacement procedures
2. Remove the power connector cable 3.
Reverse this procedure to install the power connector cable.
Fan/heat sink
✎The fan/heat sink assembly spare kit includes replacement thermal material.
✎To properly ventilate the computer, allow at least a 7.6-cm (3-in) clearance on the right side and rear panel of the 
computer. The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is 
designed to turn on automatically when high temperature conditions exist. These conditions are affected by high 
external temperatures, system power consumption, power management/battery conservation configurations, 
battery fast charging, and software requirements. Exhaust air is displaced through the ventilation grill located on 
the left side of the computer.
Before removing the heat sink, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-6).
5. Remove the following components:
a. Optical drive (see “Optical drive” on page 4-7)
b. Hard drive (see “Hard drive” on page 4-11)
c. TV tuner module (see “TV tuner module” on page 4-18)
d. Switch cover and keyboard (see “Switch cover and keyboard” on page 4-19)
Description Spare part number 
Fan/heat sink assembly 587244-001  
						

							Removal and replacement procedures
Maintenance and Service Guide4–47
e. Speaker assembly (see “Speaker assembly” on page 4-23)
f. Display assembly (see “Display assembly” on page 4-25)
g. Top cover (see “Top cover” on page 4-34)
h. System board (see “System board” on page 4-37)
i. USB board (see “USB board” on page 4-41)
Remove the fan/heat sink: 
1. Turn the system board upside down, with the expansion port and external monitor port toward you.
2. Disconnect the fan cable 1 from the system board.
3. In the order indicated on the fan/heat sink, loosen the seven Phillips captive screws 2 that secure the fan/heat 
sink assembly to the system board.
4. Remove the fan/heat sink assembly 3.
✎Due to the adhesive quality of the thermal material located between the fan/heat sink assembly and system board 
components, it may be necessary to move the fan/heat sink assembly from side to side to detach the assembly.
✎The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink assembly and the system 
board each time the fan/heat sink assembly is removed. Thermal paste is used on the processor 1 and the heat 
sink section 2 that services it. Thermal pads are used on the Northbridge chip 3 and Northbridge contact 4, the 
graphics subsystem chip 5 and graphics/heat sink contact 6 and various capacitors and their contacts 7. 
Replacement thermal material is included with all fan/heat sink assembly, system board, and processor spare part 
kits. 
						

							4–48Maintenance and Service Guide
Removal and replacement procedures
Reverse this procedure to install the fan/heat sink assembly.
Processor 
✎The processor spare part kit includes replacement thermal material. 
Before removing the processor, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6) 
5. Remove the following components: 
a. Optical drive (see “Optical drive” on page 4-7) 
b. Hard drive (see “Hard drive” on page 4-11) 
c. Switch cover and keyboard (see “Switch cover and keyboard” on page 4-19)
d. Speaker assembly (see “Speaker assembly” on page 4-23)
e. Display assembly (see “Display assembly” on page 4-25)
f. Top cover (see “Top cover” on page 4-34)
g. USB board (see “USB board” on page 4-41)
h. System board (see “System board” on page 4-37)
i. Fan/heat sink (see “Fan/heat sink” on page 4-46) 
Description Spare part number 
Intel Core2 Quad processors (8-MB L2 cache, 1333-MHz FSB): 
■i7-820QM processor (1.73-GHz, SC turbo up to 3.06-GHz) 583053-001
■i7-720QM processor (1.60-GHz, SC turbo up to 2.80-GHz) 586170-001 
						

							Removal and replacement procedures
Maintenance and Service Guide4–49
Remove the processor: 
1. Use a flat-bladed screwdriver to turn the processor locking screw 1 one-half turn counterclockwise until you 
hear a click. 
2. Lift the processor 2 straight up and remove it. 
✎When you install the processor, the gold triangle 3 on the processor must be aligned with the triangle icon 4 
embossed on the processor socket. 
 
Reverse this procedure to install the processor.  
						

							Maintenance and Service Guide5–1
5
Setup Utility
Å
WARNING: Only authorized technicians trained by HP must repair this equipment. All troubleshooting and repair procedures 
are detailed to allow repair at only the subassembly or module level. Because of the complexity of the individual boards and 
subassemblies, do not attempt to make repairs at the component level or modify any printed wiring board. Improper repairs 
can create a safety hazard. Any indication of component replacement or printed wiring board modification may void any 
warranty or exchange allowances.
Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your 
Windows® operating system is not working.
✎The fingerprint reader (select models only) cannot be used to access the Setup Utility.
The utility reports information about the computer and provides settings for startup, security, and other 
preferences.
To start the Setup Utility:
»Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
f10.
– or –
1. Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
esc.
2. When the Startup Menu is displayed, press 
f10.
Using the Setup Utility
Changing the language of the Setup Utility 
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is not 
already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1. Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
esc. When the Startup Menu is 
displayed, press 
f10.
2. Use the arrow keys to select System Configuration > Language, and then press 
enter.
3. Use the arrow keys to select a language, and then press 
enter. 
4. When a confirmation prompt with your language selected is displayed, press 
enter.  
						

							5–2Maintenance and Service Guide
Setup Utility
5. To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving Changes, and 
then press 
enter. 
Your change goes into effect immediately.
Navigating and selecting in the Setup Utility
Because the Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by 
keystroke.
■To choose a menu or a menu item, use the arrow keys.
■To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or 
f5 or f6.
■To select an item, press enter.
■To close a text box or return to the menu display, press esc.
■To display additional navigation and selection information while the Setup Utility is open, press f1.
Displaying system information 
The following procedure explains how to display system information in the Setup Utility. If the Setup Utility is not 
open, begin at step 1. If the Setup Utility is open, begin at step 2.
1. Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
esc. When the Startup Menu is 
displayed, press 
f10.
2. Select the Main menu. System information such as the system time and date, and identification information 
about the computer is displayed. 
3. To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding 
Changes, and then press 
enter.
Restoring default settings in the Setup Utility 
The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is not already 
running, begin at step 1. If the Setup Utility is already running, begin at step 2. 
1. Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup 
Menu” message is displayed in the lower-left corner of the screen, press 
esc. When the Startup Menu is 
displayed, press 
f10.
2. Use the arrow keys to select Exit > Load Setup Defaults, and then press 
enter. 
3. When the Setup Confirmation is displayed, press 
enter.
4. To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving Changes, and 
then press 
enter.  
						

							Setup Utility
Maintenance and Service Guide5–3
The Setup Utility default settings go into effect when the computer restarts.
✎Your password, security, and language settings are not changed when you restore the factory default settings. 
Exiting the Setup Utility 
You can exit the Setup Utility with or without saving changes.
■To exit the Setup Utility and save your changes from the current session: 
If the Setup Utility menus are not visible, press 
esc to return to the menu display. Then use the arrow keys to 
select Exit > Exit Saving Changes, and then press 
enter.
■To exit the Setup Utility without saving your changes from the current session: 
If the Setup Utility menus are not visible, press 
esc to return to the menu display. Then use the arrow keys to 
select Exit > Exit Discarding Changes, and then press 
enter.
After either choice, the computer restarts in Windows.
Setup Utility menus 
The menu tables in this section provide an overview of Setup Utility options. 
✎Some of the Setup Utility menu items listed in this chapter may not be supported by your computer.
Main menu
Security menu 
Select To do this 
System information■View and change the system time and date. 
■View identification information about the computer. 
■View specification information about the processor, memory size, system 
BIOS, and keyboard controller version (select models only). 
Select To do this 
Administrator password  Enter, change, or delete an administrator password. 
Power-On Password  Enter, change, or delete a power-on password.  
						

							5–4Maintenance and Service Guide
Setup Utility
System Configuration menu 
Diagnostics menu 
Select To do this 
Language Support Change the Setup Utility language.
Button Sound (select models only) Enable/disable the capacitive button tapping sound.
Virtualization Technology 
(select models only)Enable/disable the processor Virtualization Technology.
Processor C6 State (select models only) Enable/disable the processor C6 sleep state.
LAN Power Saving (select models only) Enable/disable LAN Power Saving. When enabled, saves power when the 
computer is in DC mode.
Card Reader/1394 Power Saving
(select models only)Enable/disable Card Reader/1394 Power Saving.
Fan Always On Enable/disable Fan Always On. When enabled, the computer fan will 
always be on.
Boot Options Set the following boot options: 
■f9 and f10 Delay (sec.)—Set the delay for the f9 and f10 functions of the Setup 
Utility in intervals of 5 seconds each (0, 5, 10, 15, 20). 
■CD-ROM boot—Enable/disable boot from CD-ROM. 
■Floppy boot—Enable/disable boot from diskette. 
■Internal Network Adapter boot—Enable/disable boot from Internal Network 
Adapter. 
■Boot Order—Set the boot order for:
❐USB Floppy
❐Internal CD/DVD ROM Drive
❐USB CD/DVD ROM drive
❐Hard drive
❐USB Diskette on Key
❐USB Hard drive
❐Network adapter
Select To do this 
Hard Disk Self Test Run a comprehensive self-test on the hard drive. 
✎On models with two hard drives, this menu option is called the 
Primary Hard Disk Self Test.
Secondary Hard Disk Self Test 
(select models only)Run a comprehensive self-test on a secondary hard drive. 
Memory Test Run a diagnostic test on the system memory. 
						

							Maintenance and Service Guide6–1
6
Specifications
Computer specifications 
 Metric U.S.
Dimensions
Width 46.60 cm 18.35 in 
Depth 30.90 cm 12.16 in 
Height (front to back)  3.9 to 4.7 cm  1.53 to 1.85 in 
Weight 
Equipped with optical drive, hard drive, and battery 3.75 kg  8.26 lbs 
Second hard drive adds 0.13 kg 0.28 lbs
Camera adds 0.009 kg 0.02 lbs
Input power 
Operating voltage  18.5 V dc @ 3.5 A - 65 W 
Operating current  3.5 A or 4.74 A 
Temperature 
Operating (not writing to optical disc)  0°C to 35°C  32°F to 95°F 
Operating (writing to optical disc)  5°C to 35°C  41°F to 95°F 
Nonoperating  -20°C to 60°C  -4°F to 140°F 
Relative humidity 
Operating  10% to 90% 
Nonoperating 5% to 95% 
Maximum altitude (unpressurized) 
Operating -15 m to 3,048 m  -50 ft to 10,000 ft 
Nonoperating -15 m to 12,192 m  -50 ft to 40,000 ft 
✎Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this 
range of temperatures.