HP Pavilion Dv7 1100 Entertainment Notebook Pc Series Manual

							Keyboard
For use in country or regionSpare part numberFor use in country or regionSpare part number
For use with all computer models:
Denmark, Norway, and Sweden
483275-DH1Saudi Arabia483275-171
France483275-051Spain483275-071
French Canada483275-121Switzerland483275-111
Germany483275-041Turkey483275-141
Italy483275-061The United Kingdom483275-031
The Netherlands483275-B31The United States483275-001
Portugal483275-131 
For use only with computer models equipped with AMD processors:
Asia Pacific countries and regions
483275-371Japan483275-291
Belgium483275-A41Latin America483275-161
Brazil483275-201The Netherlands483275-B31
The Czech Republic483275-221The Peoples Republic of China483275-AA1
Denmark, Norway, and Sweden483275-DH1Portugal483275-131
Europe, the Middle East,
and Africa483275-021Russia483275-251
France483275-051Saudi Arabia483275-171
French Canada483275-121Spain483275-071
Germany483275-041Switzerland483275-111
Greece483275-151Thailand483275-281
Hong Kong483275-AC1Turkey483275-141
Italy483275-061The United Kingdom483275-031
Israel 483275-BB1 The United States 483275-001
Before removing the keyboard, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 54).
5.Remove the accessory cover (see 
Hard drive on page 59).
6.Remove the switch cover (see 
Switch cover on page 69).
Component replacement procedures 71 
						

							Remove the keyboard:
1.Turn the computer upside down, with the front toward you.
2.Remove the Phillips PM2.5×13.0 screw that secures the keyboard to the computer.
3.Turn the computer display-side up, with the front toward you.
4.Open the computer as far as possible.
5.Remove the three Phillips PM2.0×4.0 screws (1) and the Phillips PM2.0×3.0 broad-head
screw (2) that secure the keyboard to the computer.
6.Lift the rear edge of the keyboard (1) until it rests at an angle.
72 Chapter 4   Removal and replacement procedures 
						

							7.Slide the keyboard (2) back to disengage the tabs on the front edge of the keyboard from the top
cover and rest it on the display.
8.Release the ZIF connector (1) to which the keyboard cable is attached and disconnect the keyboard
cable (2).
9.Remove the keyboard.
Reverse this procedure to install the keyboard.
Component replacement procedures 73 
						

							Bluetooth module
NOTE:The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 480474-001.
DescriptionSpare part number
Bluetooth module483113-001
Before removing the Bluetooth module, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 54).
5.Remove the switch cover (see 
Switch cover on page 69).
6.Remove the keyboard (see 
Keyboard on page 71)
7.Remove the following components:
Remove the Bluetooth module:
1.Remove the two Phillips PM2.0×4.0 screws (1) that secure the Bluetooth module to the top cover.
2.Release the Bluetooth module (2) as far as the Bluetooth module cable allows.
3.Disconnect the Bluetooth module cable (3) from the Bluetooth module.
4.Remove the Bluetooth module.
Reverse this procedure to install the Bluetooth module.
74 Chapter 4   Removal and replacement procedures 
						

							Speaker assembly
DescriptionSpare part number
Speaker assembly480470-001
Before removing the speaker assembly, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 54).
5.Remove the switch cover (see 
Switch cover on page 69).
6.Remove the keyboard (see 
Keyboard on page 71).
Remove the speaker assembly:
1.Disconnect the speaker assembly cable (1) from the power button board.
2.Remove the three Phillips PM2.5×4.0 screws (2) that secure the speaker assembly to the computer.
3.Remove the speaker assembly (3).
Reverse this procedure to install the speaker assembly.
Component replacement procedures 75 
						

							Display assembly
NOTE:All display assembly spare part include a webcam, microphone, and wireless antenna
transceivers and cables.
  
17.0-inch WSXGA+ AntiGlare display assembly for use only with computer models equipped with
AMD processors497104-001
17.0-inch WXGA AntiGlare display assembly for use only with computer models equipped with
AMD processors497103-001
17.0-inch WSXGA+ BrightView display assembly with webcam and 2 microphones for use only
with computer models equipped with AMD processors488881-001
17.0-inch WXGA BrightView display assembly with webcam and 2 microphones for use only with
computer models equipped with AMD processors488880-001
17.0-inch WSXGA+ AntiGlare display assembly with webcam and 2 microphones for use only with
computer models equipped with Intel processors480378-001
17.0-inch WXGA AntiGlare display assembly with webcam and 2 microphones for use only with
computer models equipped with Intel processors480377-001
17.0-inch WSXGA+ BrightView display assembly with webcam and 2 microphones for use only
with computer models equipped with Intel processors480376-001
17.0-inch WXGA BrightView display assembly with webcam and 2 microphones for use only with
computer models equipped with Intel processors480375-001
Before removing the display assembly, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 54).
5.Remove the memory/WLAN module compartment cover (see 
Memory module on page 67).
6.Disconnect the wireless antenna cables from the WLAN module (see 
WLAN module on page 64).
7.Remove the following components:
a.Switch cover (see 
Switch cover on page 69)
b.Keyboard (see 
Keyboard on page 71)
c.Speaker assembly (see 
Speaker assembly on page 75)
Remove the display assembly:
1.Disconnect the display panel cable (1) from the system board.
76 Chapter 4   Removal and replacement procedures 
						

							2.Remove the wireless antenna cables (2) from the routing channels in the top cover.
CAUTION:The display assembly will be unsupported when the following screws are removed.
To prevent damage to the display assembly, support it before removing the screws.
3.Remove the three Phillips PM2.5×13.0 screws (1) and the three Phillips PM2.5×6.0 screws (2) that
secure the display assembly to the computer.
4.Remove the display assembly (3).
NOTE:Steps 5 through 24 provide display assembly internal component removal information for
computer models equipped with AntiGlare display assemblies. See steps 25 through 40 for display
assembly internal component removal information for computer models equipped with BrightView
display assemblies.
NOTE:See Webcam/microphone module on page 56 for webcam/microphone module
replacement instructions for computer models equipped with BrightView display assemblies.
5.If it is necessary to replace the display enclosure or any of the display assembly internal
components, remove the two rubber screw covers (1) on the display bezel lower edge. The rubber
screw covers are available in the Display Rubber Kit, spare part number 495896-001.
Component replacement procedures 77 
						

							6.Remove the two Phillips PM2.5×5.0 screws (2) that secure the display enclosure to the
display assembly.
7.Turn the display enclosure upside down, with the hinges toward you.
8.Release the display enclosure (1) by sliding it toward the top of the display assembly until it
detaches from the display assembly.
9.Lift the bottom edge of the display enclosure (2) until the display enclosure logo LED cable
is accessible.
10.Disconnect the display enclosure logo LED cable (3) from the display panel cable.
11.Remove the display enclosure. The display enclosure is available using spare part number
480445-001.
12.If it is necessary to replace the webcam/microphone module, remove the two Phillips PM2.5×3.0
screws (1) that secure the webcam/microphone module to the display bezel.
13.Release the webcam/microphone module (2) as far from the display bezel as the webcam/
microphone module cable allows.
78 Chapter 4   Removal and replacement procedures 
						

							14.Disconnect the webcam/microphone module cable (3) from the webcam/microphone module.
15.Remove the webcam/microphone module. The webcam/microphone module is available using
spare part number 480446-001.
16.If it is necessary to replace the display inverter, remove the 7 Phillips PM2.5×5.0 screws (1) that
secure the display inverter cover to the display bezel.
17.Remove the display inverter cover (2) by lifting it straight up. The display inverter cover is available
using spare part number 485606-001.
18.Remove the Phillips PM2.5×5.0 screw (1) that secures the display inverter to the display bezel.
19.Release the inverter (2) as far from the display bezel as the display panel cable and backlight
cables allow.
Component replacement procedures 79 
						

							20.Disconnect the display panel cable (3) and the backlight cable (4) from the display inverter.
21.Remove the display inverter. The display inverter is available using spare part number
480447-001.
22.If it is necessary to replace the display hinges, remove the two Phillips PM2.5×5.0 screws (1) and
the four Phillips PM2.5×4.0 screws (2) that secure the display hinges to the display panel.
23.Remove the eight Phillips PM2.0×4.0 screws (1) that secure the display hinges to the display panel.
80 Chapter 4   Removal and replacement procedures