HP Pavilion Dv7 1000 Entertainment Notebook Pc Series Manual

							Where used: 4 captive screws that secure the heat sink assembly to the system board on computer
models equipped with graphics subsystems with UMA memory (screws are spring-loaded and secured
by C-clips)
Phillips PM2.0×10.0 captive screw 151 
						

							8 Backup and Recovery
Recovering system information
Recovery after a system failure is as complete as your most current backup. HP recommends that you
create recovery discs immediately after software setup. As you add new software and data files, you
should continue to back up your system on a regular basis to maintain a reasonably current backup.
Tools provided by the operating system and Recovery Manager software are designed to help you with
the following tasks for safeguarding your information and restoring it in case of a system failure:
●Making a set of recovery discs (Recovery Manager software feature). Recovery discs are used to
start up (boot) your computer and restore the operating system and software programs to factory
settings in case of system failure or instability.
●Backing up your information regularly to protect your important system files.
●Creating system restore points (operating system feature). System restore points allow you to
reverse undesirable changes to your computer by restoring the computer to an earlier state.
●Recovering a program or driver (Recovery Manager software feature). This feature helps you
reinstall a program or driver without performing a full system recovery.
●Performing a full system recovery (Recovery Manager software feature). With Recovery Manager,
you can recover your full factory image if you experience system failure or instability. Recovery
Manager works from a dedicated recovery partition (select models only) on the hard drive or from
recovery discs you create.
NOTE:If your computer includes a solid-state drive (SSD), you may not have a recovery partition.
Recovery discs have been included for computers that do not have a partition. Use these discs to recover
your operating system and software. To check for the presence of a recovery partition, select Start >
Computer. If the partition is present, an HP Recovery drive is listed in the Hard Disk Drives section of
the window.
152 Chapter 8   Backup and Recovery 
						

							Creating recovery discs
NOTE:HP recommends that you create recovery discs to be sure that you can restore your system
to its original factory state if you experience serious system failure or instability. Create these discs after
setting up the computer for the first time.
NOTE:Handle these discs carefully and keep them in a safe place. The software allows the creation
of only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●You will need high quality CD-R, DVD-R, double-layer DVD-R, DVD+R, double-layer DVD+R, or
BD-R (writable Blu-ray) discs. All these discs are purchased separately.
NOTE:Read-write discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE
(rewritable Blu-ray) discs, are not compatible with the Recovery Manager software.
●The computer must be connected to AC power during this process.
●Only one set of recovery discs can be created per computer.
●Number each disc before inserting it into the computer optical drive.
●If necessary, you can exit the program before you have finished creating the recovery discs. The
next time you open Recovery Manager, you will be prompted to continue the disc creation process.
To create a set of recovery discs:
1.Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
2.Click Advanced Options.
NOTE:If you are operating the computer on battery power, you will be prompted to connect to
AC power before you can go to the next step.
3.Click Recovery disc creation, and then click Next.
4.Follow the on-screen instructions.
Recovering system information 153 
						

							Backing up your information
When to back up
●On a regularly scheduled basis
NOTE:Set reminders to back up your information periodically.
●Before the computer is repaired or restored
●Before you add or modify hardware or software
Backup suggestions
●Create a set of recovery discs using Recovery Manager.
●Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●Store personal files in the Documents folder and back up these folders periodically.
●Back up templates stored in their associated programs.
●Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document, follow these steps:
1.Display the screen.
2.Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3.Open a word-processing document, and then select Edit > Paste.
Using system restore points
When you back up your system, you are creating a system restore point. A system restore point allows
you to save and name a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE:Recovering to an earlier restore point does not affect data files saved or e-mails created since
the last restore point.
You also can create additional restore points to provide increased protection for your system files and
settings.
154 Chapter 8   Backup and Recovery 
						

							When to create restore points
●Before you add or extensively modify software or hardware
●Periodically, whenever the system is performing optimally
NOTE:If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.Select Start > Control Panel > System and Maintenance > System.
2.In the left pane, click System Protection.
3.Click the System Protection tab.
4.Under Automatic restore points, select the disk for which you want to create a restore point.
5.Click Create.
The System Protection window opens.
6.Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally, follow these steps:
1.Select Start > Control Panel > System and Maintenance > System.
2.In the left pane, click System protection.
3.Click the System Protection tab.
4.Click the System Restore button, and then click Next.
The System Restore window opens.
5.Follow the on-screen instructions.
Backing up your information 155 
						

							Performing a recovery
NOTE:You can recover only files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure
or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition (select models only) on the hard drive. However, if your computer includes a solid-state drive
(SSD), you may not have a recovery partition. If that is the case, recovery discs have been included
with your computer. Use these discs to recover your operating system and software.
NOTE:Windows has its own built-in repair features, such as System Restore and driver roll-back
capabilities. If you have not already tried these features, try them before using Recovery Manager.
NOTE:Recovery Manager recovers only software that was preinstalled at the factory. Software not
provided with this computer must be downloaded from the manufacturers Web site or reinstalled from
the disc provided by the manufacturer.
Recovering from the recovery discs
To restore the system from the recovery discs:
1.Back up all personal files.
2.Insert the first recovery disc into the optical drive and restart the computer.
3.Follow the on-screen instructions.
Recovering from the dedicated recovery partition (select models only)
NOTE:If your computer includes a solid-state drive (SSD), you may not have a recovery partition. You
will not be able to recover using this procedure. Recovery discs have been included for computers that
do not have a partition. Use these discs to recover your operating system and software.
On some models, you can perform a recovery from the partition on the hard drive from either the Start
button or f11.
To restore the system from the partition, follow these steps:
1.Access Recovery Manager in either of the following ways:
●Select Start > All Programs > Recovery Manager > Recovery Manager.
–or–
●Restart the computer and press f11 while the “Press  for recovery” message is displayed
on the screen. Then select Recovery Manager.
2.Click Advanced Options.
3.Click System recovery, and then click Next.
4.Follow the on-screen instructions.
156 Chapter 8   Backup and Recovery 
						

							9 Connector pin assignments
1394
PinSignal
1Power
2Ground
3TPB-
4TPB+
5TPA-
6 TPA+
1394 157 
						

							Audio-in (microphone)
PinSignal
1Audio signal in
2Audio signal in
3 Ground
Audio-out (headphone)
PinSignal
1Audio out, left channel
2Audio out, right channel
3 Ground
158 Chapter 9   Connector pin assignments 
						

							External monitor
PinSignal
1Red analog
2Green analog
3Blue analog
4Not connected
5Ground
6Ground analog
7Ground analog
8Ground analog
9+5 VDC
10Ground
11Monitor detect
12DDC 2B data
13Horizontal sync
14Vertical sync
15 DDC 2B clock
External monitor 159 
						

							HDMI
PinSignal
1TMDS data 2+
2TMDS data 2 shield
3TMDS data 2–
4TMDS data 1+
5TMDS data 1 shield
6TMDS data 1–
7TMDS data 0+
8TMDS data 0 shield
9TMDS data 0–
10TMDS clock+
11TMDS clock shield
12TMDS clock-
13CEC
14No connect
15DDC clock
16DDC data
17Ground
18+5V power
19Hot plug detect
20 Shell
160 Chapter 9   Connector pin assignments