HP Pavilion Dv6800 Thrive Special Edition Entertainment Notebook Pc Series Service Guide

							Using system restore points
When you back up your system, you are creating a system restore point. A system restore point allows
you to save and name a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system. 
NOTE:Recovering to an earlier restore point does not affect data files saved or e-mails created since
the last restore point.
You also can create additional restore points to provide increased protection for your system files and
settings.
When to create restore points
●Before you add or extensively modify software or hardware
●Periodically, whenever the system is performing optimally
NOTE:If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.Select Start > Control Panel > System and Maintenance > System.
2.In the left pane, click System protection.
3.Click the System Protection tab.
4.Under Automatic restore points, select the disk for which you want to create a restore point.
5.Click Create.
The System Protection window opens.
6.Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally, follow these steps:
1.Select Start > Control Panel > System and Maintenance > System.
2.In the left pane, click System protection.
3.Click the System Protection tab.
4.Click the System Restore button, and then click Next.
The System Restore window opens.
5.Follow the on-screen instructions.
Recovering system information 133 
						

							Performing a recovery
NOTE:You can only recover files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure or
instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition on the hard drive. 
NOTE:Windows has its own built-in repair features, such as System Restore and driver roll-back
capabilities. If you have not already tried these features, try them before using Recovery Manager.
NOTE:Recovery Manager recovers only software that was preinstalled at the factory. Software not
provided with this computer must be downloaded from the manufacturers Web site or reinstalled from
the disc provided by the manufacturer.
Recovering from the recovery discs
To restore the system from the recovery discs:
1.Back up all personal files.
2.Insert the first recovery disc into the optical drive and restart the computer.
3.Follow the on-screen instructions.
Recovering from the partition on the hard drive
You can perform a recovery from the partition on the hard drive from either the Start button or f11.
To restore the system from the partition, follow these steps:
1.Access Recovery Manager in either of the following ways:
●
Select Start > All Programs > Recovery Manager > Recovery Manager.
–or–
●Restart the computer and press f11 while the “Press  for recovery” message is displayed
on the screen. Then select Recovery Manager.
Recovery Manager opens.
2.Click Advanced Options.
3.Click System recovery, and then click Next.
4.Follow the on-screen instructions.
134 Chapter 8   Backup and recovery 
						

							9
Connector pin assignments
Audio-in (microphone)
PinSignal
1Audio signal in
2Audio signal in
3Ground
Audio-out (headphone)
PinSignal
1Audio out, left channel
2Audio out, right channel
3Ground
Audio-in (microphone) 135 
						

							External monitor
PinSignal
1Red analog
2Green analog
3Blue analog
4Not connected
5Ground
6Ground analog
7Ground analog
8Ground analog
9+5 VDC
10Ground
11Monitor detect
12DDC 2B data
13Horizontal sync
14Vertical sync
15 DDC 2B clock
136 Chapter 9   Connector pin assignments 
						

							RJ-11 (modem)
PinSignal
1Unused
2Tip
3Ring
4Unused
5Unused
6Unused
RJ-45 (network)
PinSignal
1Transmit +
2Transmit -
3Receive +
4Unused
5Unused
6Receive -
7Unused
8Unused
RJ-11 (modem) 137 
						

							S-Video-out
PinSignal
1S-VHS color (C) signal
2Composite video signal
3S-VHS intensity (Y) signal
4S-VHS color ground
5TV-CD
6S-VHS intensity ground
7 Composite video ground
Universal Serial Bus
PinSignal
1+5 VDC
2Data -
3Data +
4Ground
138 Chapter 9   Connector pin assignments 
						

							10
Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country
or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries or regions
The requirements listed below are applicable to all countries or regions:
●The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●All power cord sets must be approved by an acceptable accredited agency responsible for evaluation
in the country or region where the power cord set will be used.
●The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating
of 125 or 250 V AC, as required by each country or region’s power system.
●The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries or regions 139 
						

							Requirements for specific countries or regions
Country/regionAccredited agencyApplicable note number
AustraliaEANSW1
AustriaOVE1
BelgiumCEBC1
CanadaCSA2
DenmarkDEMKO1
FinlandFIMKO1
FranceUTE1
GermanyVDE1
ItalyIMQ1
JapanMETI3
South KoreaEK4
The NetherlandsKEMA1
NorwayNEMKO1
The Peoples Republic of ChinaCCC5
SwedenSEMKO1
SwitzerlandSEV1
TaiwanBSMI4
The United KingdomBSI1
The United StatesUL2
1.The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug
must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
5.The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
140 Chapter 10   Power cord set requirements 
						

							11
Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING!The backlight contains mercury. Caution must be exercised when removing and handling
the backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION:The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components.
NOTE:Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or see
the Electronic Industries Alliance (EIA) Web site at 
http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE:The procedures provided in this appendix are general disassembly instructions. Specific details,
such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one
computer model to another.
Battery 141 
						

							Perform the following steps to disassemble the display assembly:
1.Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.Remove the display bezel (3).
142 Chapter 11   Recycling