HP Pavilion Dv6800 Thrive Special Edition Entertainment Notebook Pc Series Service Guide

							a.Hard drive (see Hard drive on page 51)
b.Optical drive (see 
Optical drive on page 59)
c.Switch cover (see 
Switch cover on page 61)
d.Keyboard (see 
Keyboard on page 65)
e.Speaker assembly (see 
Speaker assembly on page 63)
f.Display assembly (see 
Display assembly on page 68)
g.Top cover (see 
Top cover on page 74)
h.Audio board (see 
Audio board on page 85)
i.USB/power connector board (see 
USB/power connector board on page 81)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●Memory modules (see 
Memory module on page 53)
●RTC battery (see 
RTC battery on page 55)
●WLAN module (see 
WLAN module on page 56)
●Bluetooth module (see 
Bluetooth module on page 78)
●ExpressCard assembly (see 
ExpressCard assembly on page 79)
●Fan/heat sink assembly (see 
Fan/heat sink assembly on page 86)
●Processor (see 
Processor on page 88)
Remove the system board:
1.Remove the USB/power connector board cable (1) from the clips built into in the base enclosure.
2.Remove the two Phillips PM2.5×4.0 screws (2) that secure the system board to the base enclosure.
Component replacement procedures 83 
						

							3.Use the optical drive connector (1) to lift the right side of the system board (2) until it rests at an
angle.
4.Disconnect the audio board cable (3) from the system board.
5.Release the system board (4) by sliding it to the right until the connectors on the left side of the system
board disengage from the base enclosure.
6.Remove the system board.
7.If it is necessary to replace the USB/power connector board cable, turn the system board upside
down with the expansion port 3 toward you.
8.Disconnect the power connector cable (1) and the USB board cable (2) from the system board. The
USB/power connector board cable is included in the Cable Kit, spare part number 446519-001.
Reverse the above procedure to install the system board and USB/power connector board cable.
84 Chapter 4   Removal and replacement procedures 
						

							Audio board
DescriptionSpare part number
For use in full-featured models (includes audio connectors, audio board cable, and infrared lens)446523-001
For use in defeatured models (includes audio connectors, audio board cable, and infrared lens) 449967-001
Before removing the audio board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 46).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 51)
b.Optical drive (see 
Optical drive on page 59)
c.Switch cover (see 
Switch cover on page 61)
d.Keyboard (see 
Keyboard on page 65)
e.Speaker assembly (see 
Speaker assembly on page 63)
f.Display assembly (see 
Display assembly on page 68)
g.Top cover (see 
Top cover on page 74)
h.System board (see 
System board on page 82)
Remove the audio board:
1.Remove the two Phillips PM2.5×4.0 screws (1) that secure the audio board to the computer.
2.Release the audio board (2) by sliding it back to disengage the audio connectors from the openings
in the base enclosure.
Component replacement procedures 85 
						

							3.Remove the audio board (3) by lifting it straight up.
Reverse this procedure to install the audio board.
Fan/heat sink assembly
NOTE:All fan/heat sink assembly spare part kits include replacement thermal material.
DescriptionSpare part number
For use only in computer models with Intel processors: 
●Equipped with discrete graphics subsystem memory and 8.1 processors450933-001
●Equipped with discrete graphics subsystem memory and 7.9 processors434986-001
●Equipped with UMA graphics subsystem memory446521-001
For use only in computer models with AMD processors: 
●Equipped with discrete graphics subsystem memory449960-001
●Equipped with UMA graphics subsystem memory 451860-001
NOTE:When replacing the fan/heat sink assembly, be sure that the power button board is removed
from the defective fan/heat sink assembly and installed on the replacement fan/heat sink assembly.
See 
Power button board on page 64 for power button board removal information.
NOTE:To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the right side
and rear panel of the computer. The computer uses an electric fan for ventilation. The fan is controlled by
a temperature sensor and is designed to turn on automatically when high temperature conditions exist.
These conditions are affected by high external temperatures, system power consumption, power
management/battery conservation configurations, battery fast charging, and software applications.
Exhaust air is displaced through the ventilation grill located on the left side of the computer.
86 Chapter 4   Removal and replacement procedures 
						

							Before removing the fan/heat sink assembly, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 46).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 51)
b.Optical drive (see 
Optical drive on page 59)
c.Switch cover (see 
Switch cover on page 61)
d.Keyboard (see 
Keyboard on page 65)
e.Speaker assembly (see 
Speaker assembly on page 63)
f.Display assembly (see 
Display assembly on page 68)
g.Top cover (see 
Top cover on page 74)
h.Audio board (see 
Audio board on page 85)
i.USB/power connector board (see 
USB/power connector board on page 81)
j.System board (see 
System board on page 82)
Remove the fan/heat sink assembly:
1.Turn the system board upside down with the expansion port 3 and external monitor port toward you.
2.Disconnect the fan cable (1) from the system board.
3.Loosen the three Phillips PM2.5×5.0 screws (2) and the Phillips PM2.5×4.0 screw (3) that secure
the fan/heat sink assembly to the system board.
Component replacement procedures 87 
						

							4.Remove the fan/heat sink assembly (4).
NOTE:Due to the adhesive quality of the thermal paste and thermal pads located between the
fan/heat sink assembly and system board components, it may be necessary to move the fan/heat
sink assembly from side to side to detach the assembly.
NOTE:The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink
assembly (1) and (2), the processor (3), and the system board component (4) each time the fan/heat
sink assembly is removed. Thermal material must be installed on all surfaces before the fan/heat sink
assembly is reinstalled. Thermal material is included with all fan/heat sink assembly, system board, and
processor spare part kits.
Reverse this procedure to install the fan/heat sink assembly.
Processor
NOTE:All processor spare part kits include thermal paste.
DescriptionSpare part number
Intel Core 2 Duo processors:
2.20-GHz processor (4-MB L2 cache, 800-MHz FSB)
453771-001
88 Chapter 4   Removal and replacement procedures 
						

							DescriptionSpare part number
2.00-GHz processor (2-MB L2 cache, 800-MHz FSB)455515-001
1.86-GHz processor (1-MB L2 cache, 533-MHz FSB)453773–001
1.50-GHz processor (2-MB L2 cache, 667-MHz FSB)453772-001
Intel Core Duo processors:
T7300 2.00-GHz processor (2-MB L2 cache)
446478-001
T7100 1.80-GHz processor (2-MB L2 cache)446479-001
T5250 1.50-GHz processor (2-MB L2 cache)453033-001
T2330 1.6-GHz processor (1-MB L2 cache, 533-MHz FSB)455944–001
T2310 1.46-GHz processor (1-MB L2 cache, 533-MHz FSB)455943–001
Intel Celeron processor: 
M530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB)457315–001
AMD processors: 
Turion MK-38 (2.2-GHz, 512-MB L2 cache)449904-001
Turion TL-66 (2.3 -GHz, 1-MB L2 cache)450804-001
Turion TL-60 (2.0 -GHz, 1-MB L2 cache)450803-001
Turion TL-58 (1.9 -GHz, 1-MB L2 cache)450802-001
Turion TL-56 (1.8 -GHz, 1-MB L2 cache)450801-001
Athlon TK-53 (1.7-GHz. 512-MB L2 cache)451013-001
Processor bracket 
For use with 7.9 processors450370-001
For use with 8.1 processors450371-001
Before removing the processor, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 46).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 51)
b.Optical drive (see 
Optical drive on page 59)
c.Switch cover (see 
Switch cover on page 61)
Component replacement procedures 89 
						

							d.Keyboard (see Keyboard on page 65)
e.Speaker assembly (see 
Speaker assembly on page 63)
f.Display assembly (see 
Display assembly on page 68)
g.Top cover (see 
Top cover on page 74)
h.Audio board (see 
Audio board on page 85)
i.USB/power connector board (see 
USB/power connector board on page 81)
j.System board (see 
System board on page 82)
k.Fan/heat sink assembly (see 
Fan/heat sink assembly on page 86)
Remove the processor:
1.Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
2.Lift the processor (2) straight up and remove it.
NOTE:The gold triangle (3) on the processor must be aligned with the triangle icon (4) embossed
on the processor socket when you install the processor.
Reverse this procedure to install the processor.
90 Chapter 4   Removal and replacement procedures 
						

							5
Setup Utility
Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows® operating system is not working or will not load.
NOTE:The fingerprint reader (select models only) does not work when accessing the Setup Utility.
The utility reports information about the computer and provides settings for startup, security, and other
preferences.
To start the Setup Utility:
1.Turn on or restart the computer.
2.Before Windows opens and while “Press  to enter setup” is displayed in the lower-left corner
of the screen, press f10.
Starting the Setup Utility 91 
						

							Using the Setup Utility
Changing the language of the Setup Utility
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press  to
enter setup” is displayed in the lower-left corner of the screen.
2.Use the arrow keys to select System Configuration > Language, and then press enter.
3.Press f5 or f6 (or use the arrow keys) to select a language, and then press enter to select a language.
4.When a confirmation prompt with your preference selected is displayed, press enter to save your
preference.
5.To set your preferences and exit the Setup Utility, press f10 and then follow the instructions on the
screen.
Your preferences go into effect when the computer restarts in Windows.
Navigating and selecting in the Setup Utility
Because the Setup Utility is not Windows-based, it does not support the TouchPad. Navigation and
selection are by keystroke.
●To choose a menu or a menu item, use the arrow keys.
●To choose an item in a drop-down list or to toggle a field, for example an Enable/Disable field, use
either the arrow keys or f5 or f6.
●To select an item, press enter.
●To close a text box or return to the menu display, press esc.
●To display additional navigation and selection information while the Setup Utility is open, press f1.
Displaying system information
The following procedure explains how to display system information in the Setup Utility. If the Setup Utility
is not open, begin at step 1. If the Setup Utility is open, begin at step 2.
1.To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press  to
enter setup” is displayed in the lower-left corner of the screen.
2.Access the system information by using the Main menu.
3.To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter. (The computer restarts in Windows.)
92 Chapter 5   Setup Utility