HP Pavilion Dv6 1200 Artist Edition Entertainment Notebook Pc Series Manual

Switch cover and keyboard
NOTE:Only select models are equipped with media buttons on the switch cover.
DescriptionSpare part number
Switch cover for use in white computers (includes LED board and cable)518110-001
Switch cover for use in black computers (includes LED board and cable)518790-001
Switch cover for use in MTV2 artist edition computers 570205-001
KeyboardsSpare part number
White painted keyboard517864-xxx
White molded keyboard517863-xxx
Black painted keyboard518966-xxx
Black molded...

2.Remove the following screws:
(1) Two Phillips PM2.5×6.5 screws that secure the switch cover to the computer
(2) Three Phillips PM2.5×5.0 screws that secure the switch cover to the computer (inside the battery
bay)
(3) Four Phillips PM2.5×6.5 screws that secure the keyboard to the computer
3.Turn the computer display-side up, with the front toward you.
4.Open the computer as far as possible.
5.Lift the rear edge of the switch cover until it detaches from the computer.
64 Chapter 4   Removal and...

6.Move the switch cover back so it rests on the display.
7.Remove the three Phillips PM2.0×3.0 screws that secure the keyboard to the computer.
8.Lift the rear edge (1) of the keyboard.
9.Slide the keyboard (2) back until the keyboard connector on the system board is accessible.
Component replacement procedures 65 

10.Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is connected and
disconnect the cable (2) from the system board.
11.Remove the keyboard.
12.Disconnect the power button board cable (1) from the low insertion force (LIF) connector on the
system board.
13.Disconnect the LED board cable (2) from the LIF connector on the system board.
14.Remove the switch cover.
Reverse this procedure to install the switch cover and keyboard.
66 Chapter 4   Removal and replacement procedures 

Power button board
DescriptionSpare part number
Power button board (includes cable) 512834-001
Before removing the power button board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC...

Display assembly
NOTE:The display assembly includes a webcam, 2 microphones, and 2 wireless antenna transceivers
and cables.
DescriptionSpare part number
16.0-inch WXGA BrightView display assemblies: 
Non-LED for use in white computers512358-001
Non-LED for use in black computers512357-001
LED for use in white computers538349-001
LED for use in black computers538351-001
LED for use in MTV2 artist edition computers573304-001
16.0-inch WXGA AntiGlare display assemblies: 
Non-LED for use in white...

5.Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 60).
6.Remove the switch cover and keyboard (see 
Switch cover and keyboard on page 63).
Remove the display assembly:
1.Disconnect the display panel cable (1) and the webcam/microphone cable (2) from the system
board.
2.Remove the WLAN antenna cables from the clip (3) built into the top cover.
CAUTION:Support the display assembly when removing the following screws. Failure to support
the display assembly can result in...

4.Remove the display assembly (2).
NOTE:Steps 5 through 27 provide display assembly internal component removal information for
computers equipped with AntiGlare display assemblies. See steps 28 through 38 for display
assembly internal component removal information for computers equipped with BrightView display
assemblies.
NOTE:See Webcam/microphone moduleon page 49 for webcam/microphone module
replacement instructions for computers equipped with BrightView display assemblies.
5.If it is necessary to...

9.Disconnect the display logo cable (3) from the display panel cable.
10.Remove the WLAN antenna cables and the webcam cable (4) from the left hinge.
NOTE:You may have to flex the display hinge cover to remove the WLAN cables.
11.If it is necessary to replace the display inverter, remove the four Phillips PM2.5×5.0 screws (1) that
secure the display inverter cover to the display bezel. The display inverter cover is available using
spare part number 533464-001.
12.Remove the display inverter cover (2) by...

15.Slide the webcam/microphone module to the right, and then lift it from the display (2).
16.Disconnect the webcam/microphone module cable (3) from the webcam/microphone module.
17.Remove the webcam/microphone module. The webcam/microphone module is available using
spare part number 512827-001.
18.Disconnect the display inverter from the double-sided tape securing it to the display, and then
release the display inverter (1) as far from the display bezel as the display panel cable and backlight
cable...