HP Pavilion Dv6 1200 Artist Edition Entertainment Notebook Pc Series Manual

Where used: One screw that secures the power connector bracket to the base enclosure
Where used: One screw that secures the optical drive to the computer
Where used: 9 screws that secure the top cover to the base enclosure
Phillips PM2.5×7.0 screw 133 

Where used: 2 screws that secure the display bezel to the display on computers equipped with
BrightView display assemblies
Phillips PM3.0×3.5 screw
ColorQuantityLengthThreadHead diameter
Silver 4 3.5 mm 3.0 mm 4.8 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
134 Chapter 7   Screw listing 

8 Backup and Recovery
Recovering system information
Recovery after a system failure is as complete as your most current backup. HP recommends that you
create recovery discs immediately after software setup. As you add new software and data files, you
should continue to back up your system on a regular basis to maintain a reasonably current backup.
Tools provided by the operating system and HP Recovery Manager software are designed to help you
with the following tasks for safeguarding your information and...

Creating recovery discs
NOTE:HP recommends that you create recovery discs to be sure that you can restore your system
to its original factory state if you experience serious system failure or instability. Create these discs after
setting up the computer for the first time.
NOTE:Handle these discs carefully and keep them in a safe place. The software allows the creation
of only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●You will need high-quality DVD-R,...

Backing up your information
When to back up
●On a regularly scheduled basis
NOTE:Set reminders to back up your information periodically.
●Before the computer is repaired or restored
●Before you add or modify hardware or software
Backup suggestions
●Create a set of recovery discs using Recovery Manager.
●Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●Store personal files in the Documents folder and back up this folder periodically.
●Back up...

Create a system restore point
1.Select Start > Control Panel > System and Maintenance > System.
2.In the left pane, click System Protection.
3.Click the System Protection tab.
4.Under Automatic restore points, select the disk for which you want to create a restore point.
5.Click Create.
The System Protection window opens.
6.Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally,...

Performing a recovery
NOTE:You can recover only files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure
or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition (select models only) on the hard drive. However, if your computer includes a solid-state...

9 Connector pin assignments
1394
PinSignal
1Power
2Ground
3TPB-
4TPB+
5TPA-
6TPA+
Audio-in (microphone)
PinSignal
1Audio signal in
2Audio signal in
3 Ground
140 Chapter 9   Connector pin assignments 

Audio-out (headphone)
PinSignal
1Audio out, left channel
2Audio out, right channel
3Ground
External monitor
PinSignal
1Red analog
2Green analog
3Blue analog
4Not connected
5Ground
6Ground analog
7Ground analog
8Ground analog
9+5 VDC
10Ground
11Monitor detect
12DDC 2B data
13Horizontal sync
14Vertical sync
15 DDC 2B clock
Audio-out (headphone) 141 

HDMI
PinSignal
1Transition minimized differential signal (TMDS) data 2+
2TMDS data 2 shield
3TMDS data 2–
4TMDS data 1+
5TMDS data 1 shield
6TMDS data 1–
7TMDS data 0+
8TMDS data 0 shield
9TMDS data 0–
10TMDS clock+
11TMDS clock shield
12TMDS clock-
13Consumer electronic control (CEC)
14Not connected
15DDC clock
16DDC data
17Ground
18+5V power
19 Hot plug detect
142 Chapter 9   Connector pin assignments