HP Pavilion Dv6 1000 Entertainment Notebook Pc Series Manual

Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is...

Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●Place items on a grounded surface before removing items from their containers.
●Always be properly grounded when...

Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●When standing, use foot straps and a grounded floor mat....

Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 112 screws, in 11 different sizes, that must be removed, replaced, or loosened
when servicing the computer. Make special note of each screw size and location during removal and
replacement.
Service tag
When ordering parts or requesting information, provide the computer serial number and model
description provided on the service tag.
(1) Product name: This is the product name affixed to the...

Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare
part number 516499-001. There are 4 rubber feet that attach to the base enclosure in the locations
illustrated below.
Component replacement procedures 47 

Battery
DescriptionSpare part number
12-cell, 95-Wh, 8.8-Ah Li-ion battery509460-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery509459-001
6-cell, 47-Wh, 2.20-Ah Li-ion battery 509458-001
Before disassembling the computer, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by...

Webcam/microphone module
NOTE:This section applies only to computers equipped with BrightView display assemblies. See
Display assemblyon page 68 for webcam/microphone module removal instructions for computers
equipped with AntiGlare display assemblies.
NOTE:If it has been determined that the webcam/microphone module is the component that must be
replaced to complete the computer repair, the display assembly does not have to be removed. Follow
the procedures in this section to replace the...

4.Release the display bezel top edge (3) from the display enclosure.
5.Release the webcam/microphone module (1) from the display enclosure as far as the webcam/
microphone module cable allows.
6.Disconnect the webcam/microphone module cable (2) from the webcam/microphone module.
7.Remove the webcam/microphone module.
Reverse this procedure to install the webcam/microphone module.
50 Chapter 4   Removal and replacement procedures 

Optical drive
NOTE:The optical drive spare part kit includes an optical drive bezel and bracket.
DescriptionSpare part number
Blu-ray ROM DVD±R/RW SuperMulti Double-Layer Drive509420-002
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti Double-Layer Drive509421-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive 509419-002
Before removing the optical drive, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then...

7.Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
drive.
8.Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install the optical drive.
52 Chapter 4   Removal and replacement procedures