HP Pavilion Dv3000 Entertainment Notebook Pc Series Manual

Display assembly
DescriptionSpare part number
13.3-inch, WXGA BrightView display assembly for use in dv3000 models (includes webcam/
microphone module, webcam/microphone module cable, 2 microphones, and 3 wireless antenna
transceivers and cables)468806-001
13.3-inch, WXGA BrightView display assembly for use in dv3500 models with an LCD display
(includes webcam/microphone module, webcam/microphone module cable, 2 microphones, and 3
wireless antenna transceivers and cables)496107-001
13.3-inch, WXGA...

4.Remove the WLAN antenna cables from the channel (2) located between the wireless module
compartment and the memory module compartment.
5.Turn the computer right-side up, with the rear panel toward you.
6.Open the computer as far as possible.
7.Disconnect the display panel cable (1) from the system board and remove the cable from the cavity
between the system board and the display left hinge.
8.Disconnect the webcam/microphone module cable (2) from the system board.
9.Remove the WLAN antenna cables (3)...

11.Remove the display assembly (2).
12.If it is necessary to replace any of the display assembly internal components, remove the two rubber
screw covers (1) on the display bezel bottom edge. The rubber screw covers are included in the
Display Rubber Kit, spare part number 468802-001 for dv3000 models, 500966-001 for dv3500
models with an LCD display, and 502460-001 for dv3500 models with an LED display.
13.Remove the two Phillips PM2.5×5.0 screws (2) that secure the display bezel to the display...

15.Remove the display bezel (3). The display bezel is available using spare part number 468797-001
on dv3000 models, 500953-001 on dv3500 models with an LCD display, and 500954-001 on
dv3500 models with an LED display.
16.If it is necessary to replace the webcam/microphone module, release the module (1) as far as the
webcam/microphone module allows.
17.Disconnect the webcam/microphone module cable from the module (2).
18.Remove the webcam/microphone module. The webcam/microphone module is available...

20.Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
21.Remove the inverter. The display inverter is available using spare part number 468798-001 for
dv3000 models, 500957-001 for dv3500 models.
22.If it is necessary to replace the display panel, disconnect the display logo LED board cable (1) from
the display panel cable.
23.Remove the six Phillips PM2.5×5.0 screws (2) that secure the panel to the display enclosure.
24.Remove the display panel (3) from the...

26.Remove the display hinges (2) from the display panel. The display hinges are available using spare
part number 468799-001 for dv3000 models, 500959-001 for dv3500 models with an LCD display,
500960-001 for dv3500 models with an LED display.
27.If it is necessary to replace the wireless antenna transceivers and cables, remove the Phillips
PM2.5×4.0 screw (1) that secures the left transceiver to the display enclosure.
28.Detach the wireless antenna transceivers (2) from the display enclosure.
29.Remove...

31.If it is necessary to replace the webcam/microphone module cable, remove the cable from the
display enclosure. The webcam/microphone module cable is available using spare part number
468805-001.
NOTE:The webcam/microphone module cable is attached to the display enclosure with double-
sided tape.
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures 69 

System board
NOTE:All system board spare part kits include replacement thermal material.
DescriptionSpare part number
System board for use only in dv3000 models (includes replacement thermal material and power
connector cable)468499-001
System board for use only in dv3500 models (includes replacement thermal material and power
connector cable)496097-001
Before removing the system board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn...

Remove the system board:
1.Disconnect the speaker cable (1) and the Bluetooth module cable (2) from the system board.
2.Remove the two Phillips PM2.5×5.0 screws (1) that secure the system board to the base enclosure.
3.Remove the two Phillips PM2.0×4.0 screws (2) that secure the power connector to the base
enclosure.
4.Remove the power connector (3) and the RJ11 jack (4) from the clips in the base enclosure.
5.Flex the right side of the base enclosure (1) above the USB port and RJ45 jack.
Component...

6.Use the optical drive connector (2) to lift right side of the system board (3) until the USB port and
RJ45 jack are clear of the base enclosure.
7.Flex the left side of the base enclosure (1) above the external monitor port.
8.Lift back edge of the system board (2) until the external monitor port is clear of the base enclosure.
9.Flex the left side of the base enclosure (1) above the eSATA connector and HDMI connector.
10.Lift the back edge of the system board (2) until the eSATA connector and HDMI...