HP Pavilion Dm4 3000 Beats Edition Entertainment Notebook Pc Series Manual

							Adding or replacing a hard drive
CAUTION:To prevent information loss or an unresponsive system:
Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the
hard drive while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the
power button. Then shut down the computer through the operating system.
Removing the hard drive
1.Save your work and shut down the computer.
2.Disconnect all external devices connected to the computer.
3.Unplug the power cord from the AC outlet.
4.Turn the computer upside down on a flat surface.
5.Remove the battery (refer to 
Inserting or removing the battery on page 39).
6.Loosen the screw (1) on the memory module compartment cover.
7.Slide the memory module compartment cover backwards (2), and then remove the cover (3).
8.Loosen the screw (1) on the hard drive service door.
Adding or replacing a hard drive 61 
						

							9.Remove the hard drive service door (2).
10.Remove the 3 screws securing the hard drive (1) , and then pull the hard drive tab (2) to lift the
hard drive out of the hard drive bay.
11.Disconnect the hard drive cable (3), and remove the hard drive.
62 Chapter 9   Drives 
						

							Installing a hard drive
1.Connect the hard drive cable to the hard drive (1), and then insert the hard drive into the hard
drive bay (2).
2.Tighten the 3 hard drive screws to secure the drive (3).
3.Align the tabs (1) on the hard drive service door with the notches on the computer.
4.Close the hard drive service door (2).
Adding or replacing a hard drive 63 
						

							5.Tighten the screw (3) on the hard drive service door.
6.Align the tabs (1) on the memory module compartment cover with the notches on the computer.
7.Slide the cover forward(2).
8.Tighten the screw (3) on the memory module compartment cover.
9.Replace the battery.
10.Reconnect external power and external devices.
11.Turn on the computer.
64 Chapter 9   Drives 
						

							Using optical drives
Optical drives include the following:
●CD
●DVD
●Blu-ray (BD)
Identifying the installed optical drive
▲Select Start > Computer.
A list of all drives installed in your computer, including your optical drive, is displayed.
Inserting an optical disc
1.Turn on the computer.
2.Press the release button (1) on the drive bezel to release the disc tray.
3.Pull out the tray (2).
4.Hold the disc by the edges to avoid touching the flat surfaces and position the disc label-side up
over the tray spindle.
NOTE:If the tray is not fully accessible, tilt the disc carefully to position it over the spindle.
5.Gently press the disc (3) down onto the tray spindle until the disc snaps into place.
6.Close the disc tray.
NOTE:After you insert a disc, a short pause is normal. If you have not selected a media player, an
AutoPlay dialog box opens. It prompts you to select how you want to use the media content.
Using optical drives 65 
						

							Removing an optical disc
There are 2 ways to remove a disc, depending on whether the disc tray opens normally or not.
When the disc tray opens normally
1.Press the release button (1) on the drive bezel to release the disc tray, and then gently pull out
the tray (2) until it stops.
2.Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer
edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
NOTE:If the tray is not fully accessible, tilt the disc carefully as you remove it.
3.Close the disc tray and place the disc in a protective case.
66 Chapter 9   Drives 
						

							When the disc tray fails to open normally
1.Insert the end of a paper clip (1) into the release access in the front bezel of the drive.
2.Press in gently on the paper clip until the tray is released, and then pull out the tray (2) until it
stops.
3.Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer
edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
NOTE:If the tray is not fully accessible, tilt the disc carefully as you remove it.
4.Close the disc tray and place the disc in a protective case.
Using optical drives 67 
						

							Sharing optical drives
Although your computer may not have an integrated optical drive, you can access software and data,
and install applications, by sharing an optical drive connected to another computer in your network.
Sharing drives is a feature of the Windows operating system that allows a drive on one computer to
be accessible to other computers on the same network.
NOTE:You must have a network set up in order to share an optical drive; refer to Networking
on page 17 for additional information on setting up a network.
NOTE:Some discs, such as DVD movies and game discs, may be copy-protected and therefore
unusable through DVD or CD drive sharing.
To share an optical drive:
1.From the computer with the optical drive you are sharing, select Start > Computer.
2.Right-click the optical drive you want to share, and click Properties.
3.Select the Sharing tab > Advanced Sharing.
4.Select the Share this folder check box.
5.Type a name for the optical drive in the Share name text box.
6.Click Apply, and then click OK.
7.To view the shared optical drive:
Select Start > Control Panel > Network and Internet > Network and Sharing Center.
68 Chapter 9   Drives 
						

							10 Memory modules
Adding or replacing memory modules
The computer has two memory module slots. The capacity of the computer can be upgraded by
adding a memory module to the vacant expansion memory module slot or by upgrading the existing
memory module in the primary memory module slot.
WARNING!To reduce the risk of electric shock and damage to the equipment, unplug the power
cord and remove all batteries before installing a memory module.
CAUTION:Electrostatic discharge (ESD) can damage electronic components. Before beginning
any procedure, ensure that you are discharged of static electricity by touching a grounded metal
object.
NOTE:To use a dual-channel configuration with a second memory module, be sure that both
memory modules are identical.
To add or replace a memory module:
CAUTION:To prevent information loss or an unresponsive system:
Shut down the computer before adding or replacing memory modules. Do not remove a memory
module while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the
power button. Then shut down the computer through the operating system.
1.Save your work and shut down the computer.
2.Disconnect all external devices connected to the computer.
3.Unplug the power cord from the AC outlet and remove the battery.
4.Loosen the screw (1) on the memory module compartment cover.
Adding or replacing memory modules 69 
						

							5.Slide the cover backwards (2), and then remove the cover (3).
6.If you are replacing a memory module, remove the existing memory module:
a.Pull away the retention clips (1) on each side of the memory module. The memory module
tilts up.
70 Chapter 10   Memory modules