HP Pavilion 15 P000 Notebook Pc Series Manual

							Setting up a WLAN
To set up a WLAN and connect to the Internet, you need the following equipment:
●A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from
an Internet service provider
●A wireless router (2) (purchased separately)
●A wireless computer (3)
NOTE:Some modems have a built-in wireless router. Check with your ISP to determine what type
of modem you have.
The illustration below shows an example of a wireless network installation that is connected to the
Internet.
As your network grows, additional wireless and wired computers can be connected to the network to
access the Internet.
For help in setting up your WLAN, see the information provided by your router manufacturer or your
ISP.
Configuring a wireless router
For help in setting up a WLAN, see the information provided by your router manufacturer or your ISP.
NOTE:It is recommended that you initially connect your new wireless computer to the router by
using the network cable provided with the router. When the computer successfully connects to the
Internet, disconnect the cable, and access the Internet through your wireless network.
Protecting your WLAN
When you set up a WLAN or access an existing WLAN, always enable security features to protect
your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and
airports may not provide any security. If you are concerned about the security of your computer in a
hotspot, limit your network activities to email that is not confidential and basic Internet surfing.
Wireless radio signals travel outside the network, so other WLAN devices can pick up unprotected
signals. Take the following precautions to protect your WLAN:
●Use a firewall.
A firewall checks both data and requests for data that are sent to your network, and discards any
suspicious items. Firewalls are available in both software and hardware. Some networks use a
combination of both types.
●Use wireless encryption.
Wireless encryption uses security settings to encrypt and decrypt data that is transmitted over
the network. For more information, see Help and Support.
Connecting to a wireless network 19 
						

							Connecting to a WLAN
To connect to the WLAN, follow these steps:
1.Be sure that the WLAN device is on.
2.Click the network status icon in the notification area, at the far right of the taskbar.
3.Select your WLAN from the list.
4.Click Connect.
If the WLAN is a security-enabled WLAN, you are prompted to enter a security code. Type the
code, and then click OK to complete the connection.
NOTE:If no WLANs are listed, you may be out of range of a wireless router or access point.
NOTE:If you do not see the WLAN you want to connect to, click Open Network and Sharing
Center, and then click Set up a new connection or network. A list of options is displayed,
allowing you to manually search for and connect to a network or to create a new network
connection.
After the connection is made, place the mouse pointer over the network status icon in the notification
area, at the far right of the taskbar, to verify the name and status of the connection.
NOTE:The functional range (how far your wireless signals travel) depends on WLAN
implementation, router manufacturer, and interference from other electronic devices or structural
barriers such as walls and floors.

A Bluetooth device provides short-range wireless communications that replace the physical cable
connections that traditionally link electronic devices such as the following:
●Computers (desktop, notebook, PDA)
●Phones (cellular, cordless, smart phone)
●Imaging devices (printer, camera)
●Audio devices (headset, speakers)
●Mouse
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network
(PAN) of Bluetooth devices. For information about configuring and using Bluetooth devices, see the
Bluetooth software Help.
Connecting to a wired network (select models only)
Connecting to a local area network (LAN)
Use a LAN connection if you want to connect the computer directly to a router in your home (instead
of working wirelessly), or if you want to connect to an existing network at your office.
Connecting to a LAN requires an 8-pin, RJ-45 network cable.
To connect the network cable, follow these steps:
1.Plug the network cable into the network jack (1) on the computer.
20 Chapter 3   Connecting to a network 
						

							2.Plug the other end of the network cable into a network wall jack (2) or router.
NOTE:If the network cable contains noise suppression circuitry (3), which prevents
interference from TV and radio reception, orient the circuitry end of the cable toward the
computer.
Connecting to a wired network (select models only) 21 
						

							4 Enjoying entertainment features
Use your HP computer as an entertainment hub to socialize via the webcam, enjoy and manage your
music, and download and watch movies. Or, to make your computer an even more powerful
entertainment center, connect external devices like a monitor, projector, or TV, or speakers and
headphones.
Multimedia features
Here are some of the entertainment features on your computer.
Component Description
(1)  Memory card reader Reads optional memory cards that store, manage, share, or
access information.
To insert a card:
Hold the card label-side up, with connectors facing the slot,
insert the card into the slot, and then push in on the card
until it is firmly seated.
To remove a card:
Press in on the card it until it pops out.
(2)
USB 3.0 ports (2) Each USB 3.0 port connects an optional USB device, such
as a keyboard, mouse, external drive, printer, scanner or
USB hub.
(3)
HDMI port Connects an optional video or audio device, such as a
high-definition television, any compatible digital or audio
component, or a high-speed HDMI device.
22 Chapter 4   Enjoying entertainment features 
						

							Component Description
(4)  Speakers (2) Produce sound.
(5)  Internal microphones (2) Record sound.
(6)  Webcam light On: The webcam is in use.
(7)  Webcam Records video and captures photographs. Some models
allow you to video conference and chat online using
streaming video.
For information on using the webcam, select Start > All
Programs > Communication and Chat > Cyberlink YouCam
5.
(8)  Optical drive Depending on your computer model, reads an optical disc
or reads and writes to an optical disc.
NOTE:For disc compatibility information, go to the Help
and Support web page (see 
More HP resources
on page 2). Follow the web page instructions to select your
computer model. Select Drivers & Downloads, and then
follow the on-screen instructions.
(9)
USB 2.0 port Connects an optional USB device, such as a keyboard,
mouse, external drive, printer, scanner or USB hub.
(10)
Audio-out (headphone)/Audio-in
(microphone) jackConnects optional powered stereo speakers, headphones,
earbuds, a headset, or a television audio cable. Also
connects an optional headset microphone. This jack does
not support optional microphone-only devices.
WARNING!To reduce the risk of personal injury, adjust
the volume before putting on headphones, earbuds, or a
headset. For additional safety information, see the
Regulatory, Safety, and Environmental Notices. To access
the user guides, select Start > Help and Support > User
Guides.
NOTE:When a device is connected to the jack, the
computer speakers are disabled.
NOTE:Be sure that the device cable has a 4-conductor
connector that supports both audio-out (headphone) and
audio-in (microphone).
Using the webcam
The computer has an integrated webcam that records video and captures photographs. Some models
may allow you to video conference and chat online using streaming video.
▲To start the webcam, select Start > All Programs > Communication and Chat > CyberLink
YouCam 5.
For details about using the webcam, select Start > Help and Support.
Using audio
On your computer, or on select models using an external optical drive, you can play music CDs,
download and listen to music, stream audio content from the web (including radio), record audio, or
Using the webcam 23 
						

							mix audio and video to create multimedia. To enhance your listening enjoyment, attach external audio
devices such as speakers or headphones.
Connecting speakers
You can attach wired speakers to your computer by connecting them to USB ports (or the audio-out
jack) on your computer or on a docking station.
To connect wireless speakers to your computer, follow the device manufacturer's instructions. To
connect high-definition speakers to the computer, see 
Setting up HDMI audio on page 26. Before
connecting audio devices, be sure to adjust the volume.
Connecting headphones and microphones
You can connect wired headphones or headsets to the audio-out (headphone)/audio-in (microphone)
jack on your computer. Many headsets with integrated microphones are commercially available.
To connect 
wireless headphones or headsets to your computer, follow the device manufacturer's
instructions.
WARNING!To reduce the risk of personal injury, lower the volume setting before putting on
headphones, earbuds, or a headset. For additional safety information, see the 
Regulatory, Safety and
Environmental Notices
. To access this guide, select Start > HP Support Assistant  > Next > My
computer > User Guides.
Using Beats Audio (select models only)
Beats Audio is an enhanced audio feature that provides a deep, controlled bass while maintaining a
clear sound. You can experience Beats Audio through the computer's internal speakers, through
external speakers connected to a USB port, or through Beats Audio headphones connected to the
headphone jack.
Accessing Beats Audio Control Panel
Beats Audio Control Panel allows you to view and manually control audio and bass settings.
▲To open Beats Audio Control Panel, select Start > Control Panel > Hardware and Sound > Beats
Audio Control Panel.
Enabling and Disabling Beats Audio
▲To enable or disable Beats Audio, press the fn key in combination with the b key.
Testing your audio features
To check the audio functions on your computer, follow these steps:
1.Select Start > Control Panel > Hardware and Sound > Sound.
2.When the Sound window opens, click the Sounds tab. Under Program Events, select any sound
event, such as a beep or alarm, and click the Test button.
To check the recording functions on your computer, follow these steps:
1.Select Start > All Programs > Accessories > Sound Recorder.
2.Click Start Recording and speak into the microphone.
24 Chapter 4   Enjoying entertainment features 
						

							3.Save the file to your desktop.
4.Open a multimedia program and play the recording.
To confirm or change the audio settings on your computer, select Start > Control Panel > Hardware
and Sound > Sound.
Using video
Your computer is a powerful video device that enables you to watch streaming video from your
favorite websites and download video and movies to watch on your computer, without needing to
access a network.
To enhance your viewing enjoyment, use one of the video ports on the computer to connect an
external monitor, projector, or TV. Most computers have a high-definition multimedia interface (HDMI)
port, which allows you to connect a high-definition monitor or TV.
IMPORTANT:Be sure that the external device is connected to the correct port on the computer,
using the correct cable. Check the device manufacturer's instructions if you have questions.
Connecting video devices by using an HDMI cable
NOTE:To connect an HDMI device to your computer, you need an HDMI cable, sold separately.
To see the computer screen image on a high-definition TV or monitor, connect the high-definition
device according to the following instructions.
To connect a high-definition TV or monitor to your computer:
1.Connect one end of the HDMI cable to the HDMI port on the computer.
2.Connect the other end of the cable to the high-definition TV or monitor.
3.Press f4 to alternate the computer screen image between 4 display states:
●Computer only: View the screen image on the computer only.
●Duplicate: View the screen image simultaneously on both the computer and external
device.
Using video 25 
						

							●Extend: View the screen image extended across both the computer and external device.
●External device only: View the screen image on the external device only.
Each time you press f4, the display state changes.
NOTE:Adjust the screen resolution of the external device, especially if you choose the
“Extend” option. Go to Start > Control Panel > Appearance and Personalization > Adjust screen
resolution for best results.
Setting up HDMI audio
HDMI is the only video interface that supports high-definition video and audio. After you connect an
HDMI TV to the computer, you can then turn on HDMI audio by following these steps:
1.Right-click the Speaker icon in the notification area, at the far right of the taskbar, and then click
Playback devices.
2.On the Playback tab, click Digital Output Device (HDMI).
3.Click Set Default, and then click OK.
To return the audio stream to the computer speakers, follow these steps:
1.Right-click the Speakers icon in the notification area, at the far right of the taskbar, and then click
Playback devices.
2.On the Playback tab, click Speakers.
3.Click Set Default, and then click OK.
26 Chapter 4   Enjoying entertainment features 
						

							5 Navigating the screen
You can navigate the computer screen in the following ways:
●Touch gestures
●Keyboard and mouse
Touch gestures can be used on your computer's TouchPad or on a touch screen (select models
only).
NOTE:An external USB mouse (purchased separately) can be connected to one of the USB ports
on the computer.
Select computer models have special action keys or hot key functions on the keyboard to perform
routine tasks.
Some computer models may also have an integrated numeric keypad.
Using the TouchPad and gestures
The TouchPad allows you to navigate the computer screen and control the pointer by using simple
finger movements. You can customize the touch gestures by changing settings, button configurations,
click speed, and pointer options. You can also view demonstrations of TouchPad gestures.
Select Start > Control Panel > Hardware and Sound > Synaptics ClickPad v1.0.
TIP:Use the left and right buttons on the TouchPad as you would use the corresponding buttons on
an external mouse.
NOTE:TouchPad gestures are not supported in all programs.
Using the TouchPad and gestures 27 
						

							Tapping
To make an on-screen selection, use the tap function on the TouchPad.
●Point to an item on the screen, and then tap one finger on the TouchPad zone to make a
selection. Double-tap an item to open it.
28 Chapter 5   Navigating the screen