HP Lp2480zx User Guide

							Power Source90 — 265 VAC, 45–63 Hz 
Altitude:
Operating
Storage
0 to 3657.6 m
0 to 12192 m0 to 12,000 feet
0 to 40,000 feet
Power Consumption (maximum)
						

							Recognizing Preset Display Resolutions
The display resolutions listed below are the most commonly used modes and are set as factory defaults.
This monitor automatically recognizes these preset modes and they will appear properly sized and
centered on the screen.
Table C-2  LP2480zx Model Factory Preset Display Modes
PresetPixel FormatHorz Freq (kHz)Horz
PolarityVert Freq (Hz)Vert
PolarityPixel Clk
(MHz)Source
1640 × 48031.47–59.94–25.175VGA
2640 × 48037.50–75.00–31.500VGA
3720 × 40031.47–70.08+28.321VGA
4800 × 60037.88+60.32+40.000VESA
51024 × 76848.36–60.00–65.000VESA
61152 × 72044.86–60.0o+66.750CVT 0.83MA
DVT 16:10
71280 × 76847.396+60.00–68.250CVT
0.98M9-R
81280 × 96060.00+
–60.00+
–108.000VESA
91280 × 102463.98+60.02+108.000VESA
101600 x 100061.648+60.00–108.500CVT
1.60MA-R
111600 × 120075.00+60.00+162.000VESA
121680 × 105065.29–60.00+146.250CVT 1.76MA
131920 × 108067.158–60.00+173.000CVT 2.07M9
DTV 16:9
141920 × 120059.257–47.943+150.750CVT
151920 × 120074.04+60.00–154.000CVT
2.30MA-R
161920 × 120074.56–60.00+193.250CVT 2.30MA
172048 x 108053.347–47.931+144.250CVT
182048 x 108066.576+59.924–147.000CVT-R
192048 x 120059.283–47.964+161.250CVT
20 2048 x 1200 74.049 + 59.959 – 163.500 CVT-R
NOTE:The 2048 x 1200 – 60 Hz mode is only supported on the DVI Digital, HDMI, and DisplayPort
inputs.
The following high definition modes are also supported.
46 Appendix C   Technical Specifications
 
						

							Table C-3  LP2480zx Model High Definition Video Formats
PresetTiming NamePixel FormatHorz Freq
(kHz)Vert Freq
(kHz)Pixel Rate
(MHz)OSD Display
1480i720 x 48015.7346013.5480i
2480p720 x 48031.4696027480p
3720p601280 x 720456074.25720p-60Hz
41080i601920 x 108033.756074.251080i-60Hz
5576i720 x 57615.6255013.5576i
6576p720 x 57631.255027576p
7720p501280 x 72037.55074.25720p-50Hz
81080i501920 x 108028.1255074.251080i-50Hz
91080p601920 x 108067.560148.51080p-60Hz
10 1080p50 1920 x 1080 56.25 50 148.5 1080p-50Hz
Entering User Modes
The video controller signal may occasionally call for a mode that is not preset if:
●You are not using a standard graphics adapter.
●You are not using a preset mode.
It this occurs, you may need to readjust the parameters of the monitor screen by using the on-screen
display. Your changes can be made to any or all of these modes and saved in memory. The monitor
automatically stores the new setting, then recognizes the new mode just as it does a preset mode. In
addition to the factory preset modes, there are twenty user modes that can be entered and stored.
Energy Saver Feature
When the monitor is in its normal operating mode, the monitor uses less than 90 watts of power and the
Power light is green.
The monitor also supports a reduced power state. The reduced power state will be entered into if the
monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal. Upon
detecting the absence of these signals, the monitor screen is blanked, the backlight is turned off, and
the power light is turned amber. When the monitor is in the reduced power state, the monitor will utilize
less than 3 watts of power. There is a brief warm up period before the monitor will return to its normal
operating mode.
Refer to the computer manual for instructions on setting energy saver features (sometimes called power
management features).
NOTE:The above power saver feature only works when connected to computers that have energy
saver features.
By selecting the settings in the monitors Energy Saver utility, you can also program the monitor to enter
into the reduced power state at a predetermined time. When the monitors Energy Saver utility causes
the monitor to enter the reduced power state, the power light blinks amber.
Entering User Modes 47
 
						

							D Agency Regulatory Notices
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and the receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by Hewlett Packard Company may void the users authority to operate the
equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods
to maintain compliance with FCC Rules and Regulations.
Declaration of Conformity for Products Marked with the
FCC Logo (United States Only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received, including interference that may cause
undesired operation.
For questions regarding the product, contact:
48 Appendix D   Agency Regulatory Notices
 
						

							Hewlett Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
Or, call 1-800-HP-INVENT (1-800 474-6836)
For questions regarding this FCC declaration, contact:
Hewlett Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
Or, call (281) 514-3333
To identify this product, refer to the Part, Series, or Model number found on the product.
Canadian Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Avis Canadien
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
European Union Regulatory Notice
This product complies with the following EU Directives:
●Low Voltage Directive 2006/95/EC
●EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for
this product or product family.
This compliance is indicated by the following conformity marking placed on the product:
This marking is valid for non-Telecom
products and EU harmonized Telecom
products (e.g. Bluetooth)This marking is valide for EU non-
harmonized Telecom products.
*Notified body number (used only if
applicable — refer to the product label).
Canadian Notice 49
 
						

							Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany
German Ergonomics Notice
HP products which bear the “GS” approval mark, when forming part of a system comprising HP brand
computers, keyboards and monitors that bear the “GS” approval mark, meet the applicable ergonomic
requirements. The installation guides included with the products provide configuration information.
Japanese Notice
Korean Notice
Power Cord Set Requirements
The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the
monitor to operate on input voltages between 100–120V or 200–240V.
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use
in the country where you purchased the equipment.
If you need to obtain a power cord for a different country, you should purchase a power cord that is
approved for use in that country.
The power cord must be rated for the product and for the voltage and current marked on the products
electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and
current rating marked on the product. In addition, the cross-sectional area of the wire must be a minimum
of 0.75 mm² or 18 AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m).
If you have questions about the type of power cord to use, contact an authorized HP service provider.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon
it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the
cord exits from the product.
Japanese Power Cord Requirements
For use in Japan, use only the power cord received with this product.
50 Appendix D   Agency Regulatory Notices
 
						

							CAUTION:Do not use the power cord received with this product on any other products.
Product Environmental Notices
Materials Disposal
This HP product contains mercury in the fluorescent lamp in the display LCD that might require special
handling at end-of-life.
Disposal of this material can be regulated because of environmental considerations. For disposal or
recycling information, contact the local authorities or the Electronic Industries Alliance (EIA)
http://www.eiae.org.
Disposal of Waste Equipment by Users in Private Household in the
European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your household waste. Instead, it is your responsibility to dispose of your waste equipment by handing
it over to a designated collection point for the recycling or waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of disposal will help to
conserve natural resources and ensure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your waste equipment for recycling,
please contact the local city office, the household waste disposal service or the shop where you
purchased the product.
Chemical Substances
HP is committed to providing our customers with information about the chemical substances in our
products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006
of the European Parliament and the Council). A chemical information report for this product can be found
at: 
http://www.hp.com/go/reach
Restriction of Hazardous Substances (RoHS)
A Japanese regulatory requirement, defined by specification JIS C 0950, 2005, mandates that
manufacturers provide Material Content Declarations for certain categories of electronic products
offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit
http://www.hp.com/go/jisc0950.
Product Environmental Notices 51
 
						

							11363-2006
11363-2006
52 Appendix D   Agency Regulatory Notices
 
						

							E LCD Monitor Quality and Pixel Policy
The TFT monitor uses high-precision technology, manufactured according to HP standards, to
guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that
appear as small bright or dark spots. This is common to all LCD displays used in products supplied by
all vendors and is not specific to the HP LCD. These imperfections are caused by one or more defective
pixels or sub-pixels.
●A pixel consists of one red, one green, and one blue sub-pixel.
●A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off
(a dark spot on a bright background). The first is the more visible of the two.
●A defective sub-pixel (dot defect) is less visible than a defective whole pixel and is small and only
visible on a specific background.
To locate defective pixels, the monitor should be viewed under normal operating conditions, in normal
operating mode at a supported resolution and refresh rate, from a distance of approximately 50 cm (20
in).
HP expects that, over time, the industry will continue to improve its ability to produce LCDs with fewer
cosmetic imperfections and HP will adjust guidelines as improvements are made.
53