HP Lp2480zx User Guide

							WARNING!If an LCD monitor is not positioned in a sufficiently stable location, it can be potentially
hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple
precautions such as:
• Using cabinets or stands recommended by the manufacturer of the LCD monitor.
• Only using furniture that can safely support the LCD monitor.
• Ensuring the LCD monitor is not overhanging the edge of the supporting furniture.
• Not placing the LCD monitor on tall furniture (for example, cupboards or bookcases) without anchoring
both the furniture and the LCD monitor to a suitable support.
• Not standing the LCD monitor on cloth or other materials placed between the LCD monitor and
supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the LCD monitor or its controls.
Maintenance Guidelines
To enhance the performance and extend the life of the monitor:
●Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those
controls that are covered in the operating instructions. If the monitor is not operating properly or
has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider.
●Use only a power source and connection appropriate for this monitor, as indicated on the label/
back plate of the monitor.
●Be sure the total ampere rating of the products connected to the outlet does not exceed the current
rating of the electrical outlet, and the total ampere rating of the products connected to the cord does
not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS
or A) for each device.
●Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the
plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
●Turn the monitor off when not in use. You can substantially increase the life expectancy of the
monitor by using a screen saver program and turning off the monitor when not in use.
●Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked
or covered. Never push objects of any kind into cabinet slots or other openings.
●Do not drop the monitor or place it on an unstable surface.
●Do not allow anything to rest on the power cord. Do not walk on the cord.
●Keep the monitor in a well-ventilated area, away from excessive light, heat or moisture.
●When removing the monitor base, you must lay the monitor face down on a soft area to prevent it
from getting scratched, defaced, or broken.
Maintenance Guidelines 5
 
						

							Cleaning the Monitor
1.Turn off the monitor and the computer.
2.Unplug the monitor from the wall outlet.
3.Clean the monitor plastics with a clean cloth dampened with water.
4.Clean the monitor screen with an antistatic screen cleaner.
CAUTION:Do not use benzene, thinner, ammonia, or any other volatile substances to clean the
monitor or the screen. These chemicals may damage the cabinet finish as well as the screen.
Shipping the Monitor
Keep the original packing box in a storage area. You may need it later if you move or ship the monitor.
6 Chapter 2   Safety and Maintenance Guidelines
 
						

							3 Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other
attached devices, then follow the instructions below.
NOTE:Be sure the master power switch, located on the rear panel of the monitor, is in the off position.
The master power switch turns off all power to the monitor.
CAUTION:For proper ventilation, the monitor must have a minimum of 5 cm (2 inches) of clearance
around all sides and the cooling fan below the handle must not be blocked.
Installing the Monitor Pedestal Base
NOTE:Do not install the pedestal base if the monitor will be used on a wall, swing arm, or other
mounting fixture; instead see 
Mounting the Monitor on page 16 in this chapter.
1.Using both hands, position the monitor over the pedestal base.
CAUTION:Do not touch the surface of the LCD panel. Pressure on the panel may cause non-
uniformity of color or disorientation of the liquid crystals. If this occurs the screen will not recover
to its normal condition.
2.Press down firmly on the monitor to lock the pedestal base in place. When the base locks, it will
make a clicking sound.
Figure 3-1  Inserting the Monitor into the Pedestal Base
Installing the Monitor Pedestal Base 7
 
						

							NOTE:Be sure the pedestal base is securely locked before continuing with the setup.
Rear Components
Figure 3-2  Rear Components
Table 3-1  HP LP2480zx Rear Components
Component Function
1USB Downstream Connectors
(side panel)Connects optional USB devices to the monitor.
2Cable Lock ProvisionProvides slot for use with cable security locks.
3DisplayPort ConnectorConnects the DisplayPort signal cable to the monitor.
4HDMI ConnectorConnects the HDMI signal cable to the monitor.
5DVI-I ConnectorsConnects the DVI-I to VGA signal cable or DVI-I to DVI-D
signal cable to the monitor.
6Component ConnectorsConnects Component signal cables to the monitor.
7S-Video ConnectorConnects an S-Video signal cable to the monitor.
8Composite ConnectorConnects a Composite signal cable to the monitor.
9USB Upstream ConnectorConnects the monitor USB hub to a host USB port/hub.
10Master Power SwitchTurns off all power to the monitor.
11 AC Power Connector Connects the AC power cord to the monitor.
8 Chapter 3   Setting Up the Monitor
 
						

							Selecting and Connecting the Signal Cables
The monitor features two DVI-I connectors capable of supporting either analog or digital input, one
DisplayPort connector, one HDMI connector, one set of Component connectors, one S-Video connector,
and one Composite connector.
The monitor will automatically select an active signal on the DVI, HDMI, and DisplayPort inputs. The
Component, S-Video, and Composite inputs must be selected manually. The inputs can be selected
through the On-Screen Display (OSD) feature by pressing the Input button on the front panel.
NOTE:Refer to Rear Components on page 8 for signal input connector locations.
Table 3-2  Signal Connectors and Cables
InputMonitor Connector and Cable
PlugConnection Description
DVI-IThe video mode supported by the DVI-I connectors are determined by the
video cable used.
●For digital operation, use the DVI-I to DVI-D signal cable provided.
Connect the DVI-I to DVI-D signal cable to the DVI-I connector on
the monitor and the other end to the DVI-D connector on the
computer.
●For analog operation, use the DVI-I to VGA signal cable provided.
Connect the DVI-I to VGA signal cable to a DVI-I connector on the
monitor and the other end to the VGA connector on the computer.
DisplayPortConnect the DisplayPort cable provided to the DisplayPort connector on
the monitor and the DisplayPort connector on the computer for digital
operation.
NOTE:The DisplayPort cable locks in place when it is connected. To
remove a DisplayPort cable, press the button on top of the cable end and
pull the cable end from the connector.
HDMIConnect the HDMI cable provided to the HDMI connector on the monitor
and the HDMI connector on the input device for digital operation.
Component
(Y Pb Pr)Connect a set of Component cables to the Component connectors on the
monitor and the Component connectors on the input device for analog
operation. Cable set purchased separately.
Selecting and Connecting the Signal Cables 9
 
						

							InputMonitor Connector and Cable
PlugConnection Description
S-VideoConnect an S-Video cable to the S-Video connector on the monitor and
the S-Video connector on the input device for analog operation. Cable
purchased separately.
CompositeConnect a Composite cable to the Composite connector on the monitor
and the Composite connector on the input device for analog operation.
Cable purchased separately.
Cable Management
Before connecting the cables, route them through the opening on the neck of the monitors pedestal.
Figure 3-3  Using the Cable Management Feature
Table 3-2  Signal Connectors and Cables (continued)
10 Chapter 3   Setting Up the Monitor
 
						

							Connecting the Monitor Power
1.Place the monitor in a convenient, well-ventilated location near the computer.
2.Connect one end of the power cable to the AC power connector on the back of the monitor (1),
and the other end to an electrical wall outlet (2).
Figure 3-4  Connecting the Power Cable
WARNING!To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
• Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
For your safety, do not place anything on power cords or cables. Arrange them so that no one may
accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical
outlet, grasp the cord by the plug.
Connecting the Monitor Power 11
 
						

							Connecting USB Devices
The monitor provides four USB connectors on the side panel that can be used to connect devices such
as a digital camera, USB keyboard, or USB mouse.
1.Connect one end of the USB hub cable to the USB connector on the rear panel of the computer,
and the other end to the upstream USB connector on the monitor.
2.Connect the USB devices to the USB downstream connectors on the side panel of the monitor.
Figure 3-5  Connecting USB Devices
Adjusting the Monitor
1.Tilt the monitors panel forward or backward to set it to a comfortable eye level.
Figure 3-6  Tilting the Monitor
12 Chapter 3   Setting Up the Monitor
 
						

							2.Swivel the monitor to the left or right for the best viewing angle.
Figure 3-7  Swiveling the Monitor
3.Adjust the monitors height so that it is parallel to your eye height for a comfortable viewing position.
WARNING!A lock-down/release button on the front of the column prevents the display panel
from sliding up when the monitor is lifted. If the display panel is locked in the lowest height position:
a. Make sure that the monitor is safely positioned on a stable surface.
b. Gently push down on the display panel.
c. While pushing down the display panel, press the lock-down/release button on the front of the
column.
d. Guide the display panel up to the desired height.
Figure 3-8  Adjusting the Height
Adjusting the Monitor 13
 
						

							4.Pivot the monitor clockwise from landscape to portrait orientation viewing to adapt to your
application.
CAUTION:USB cables that are connected to the monitor can be damaged if they come in contact
with the desk or table top surface when rotating the display panel to the portrait position. Ensure
that there is enough clearance for the USB cables as you rotate the monitor.
Be sure to remove any cables from the cable management opening before pivoting the monitor.
Figure 3-9  Pivoting the Monitor
NOTE:To view information on the screen in portrait mode, you will need to install the HP Display
Assistant software included on the software and documentation CD. The position of the OSD menu
can also be rotated to portrait mode. To rotate the OSD menu, press the Menu button on the
monitors front panel, then select OSD Control > OSD Rotation.
CAUTION:Monitor display panel orientations of 180 and 270 degrees are not supported and may
result in damage to the monitor.
Turning on the Monitor
1.Press the power switch to turn on the computer.
2.Verify the master power switch on the rear of the monitor is in the on (I) position.
3.Press the power button on the front of the monitor.
CAUTION:Burn-in image damage may occur on monitors that display the same static image on
screen for a prolonged period of time.* To avoid burn-in image damage on the monitor screen, you
should always activate a screen saver application or turn off the monitor when it is not in use for a
prolonged period of time. Image retention is a condition that may occur on all LCD screens.
* A prolonged period of time is 12 consecutive hours of non-use.
NOTE:After turning on the monitor, a minimum 30 minute warm-up time is required for best
performance.
14 Chapter 3   Setting Up the Monitor