HP Lp2065 User Guide

2 Safety and Maintenance Guidelines
Important Safety Information
A power cord is included with the monitor. If another cord is used, use only a power source and
connection appropriate for this monitor. For information on the correct power cord set to use with the
monitor, refer to the 
Power Cord Set Requirements on page 40 section in Appendix C.
WARNING!To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding feature. The grounding plug is an important...

Maintenance Guidelines
To enhance the performance and extend the life of the monitor:
●Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those
controls that are covered in the operating instructions. If the monitor is not operating properly or
has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider.
●Use only a power source and connection appropriate for this monitor, as indicated on the label/
back plate of the monitor.
●Be sure...

3 Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other
attached devices, then follow the instructions below.
NOTE:Be sure the master power switch, located on the rear panel of the monitor, is in the off position.
The master power switch turns off all power to the monitor.
Installing the Monitor Pedestal Base
NOTE:Do not install the pedestal base if the monitor will be used on a wall, swing arm, or other
mounting fixture; instead see...

Rear Components
Figure 3-2  Rear Components
Component Function
1Cable Lock ProvisionProvides slot for use with cable security locks.
2Master Power SwitchTurns off all power to the monitor.
3AC Power ConnectorConnects the AC power cord to the monitor.
4DVI-I ConnectorsConnects the DVI-I to VGA signal cable or DVI-D signal cable
to the monitor.
5USB Upstream
ConnectorConnects the monitor USB hub to a host USB port/hub.
6USB Downstream
ConnectorsConnects optional USB devices to the monitor.
7 USB...

Selecting the Signal Connectors and Cables
The monitor features two DVI-I connectors capable of supporting either analog or digital input.
The video mode supported by the DVI-I connector is determined by the video cable used.
●For digital operation, use the DVI-D signal cable provided. Connect the DVI-D signal cable to a
DVI-I connector on the monitor and the other end to the DVI connector on the computer.
●For analog operation, use the DVI-I to VGA signal cable provided. Connect the DVI-I to VGA signal...

Connecting the Monitor
1.Place the monitor in a convenient, well-ventilated location near the computer.
2.Connect one end of the USB hub cable to the USB connector on the rear panel of the computer,
and the other end to the upstream USB connector on the monitor.
Figure 3-5  Connecting the USB Cable
WARNING!To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
• Plug the power cord into a grounded...

4.Place the cables through the cable management channel on the back of the monitor base.
Figure 3-7  Using the Cable Management Feature
Adjusting the Monitor
1.Tilt the monitors panel forward or backward to set it to a comfortable eye level.
Figure 3-8  Tilting the Monitor
NOTE:The 24 model has a tilt range of -5 to +25 degrees.
ENWWAdjusting the Monitor 9
 

2.Swivel the monitor to the left or right for the best viewing angle.
Figure 3-9  Swiveling the Monitor
3.Adjust the monitors height so that it is parallel to your eye height for a comfortable viewing position.
WARNING!A lock-down/release button on the front of the column prevents the display head of
the 19 model from sliding up when the monitor is lifted. If the display head is locked in the lowest
height position:
a. Make sure that the monitor is safely positioned on a stable surface.
b. Gently push...

4.Pivot the monitor from landscape to portrait orientation viewing to adapt to your application.
Figure 3-11  Pivoting the Monitor
NOTE:The 20 model (shown above) pivots counter-clockwise; the 19 and 24 models pivot
clockwise.
To view information on the screen in portrait mode, you will need to install the Pivot Pro software
included on the software and documentation CD.
Turning on the Monitor
1.Press the power switch to turn on the computer.
2.Press the master power switch on the rear of the monitor....

Connecting USB Devices
The monitor provides four USB connectors, two on the side panel and two on the rear panel, used to
connect devices such as a digital camera, USB keyboard, or USB mouse.
NOTE:You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0
ports on the monitor. Refer to Step 2 in 
Connecting the Monitor on page 8.
Figure 3-12  Connecting USB Devices
12 Chapter 3   Setting Up the Monitor ENWW