HP Le1851w User Guide

●Be sure the total ampere rating of the products connected to the outlet does not exceed the current
rating of the electrical outlet, and the total ampere rating of the products connected to the cord
does not exceed the rating of the cord. Look on the power label to determine the ampere rating
(AMPS or A) for each device.
●Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the
plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling...

3 Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other
attached devices, then follow the instructions below.
Attaching the Monitor Base
1.Set the base on a flat surface such as a table top.
2.Using both hands, position the pedestal over the base and press down firmly to lock it in place. Be
sure the base is securely locked in place and adjust the tilt angle to the desired position.
CAUTION:Do not touch the surface of the LCD panel....

Rear Components
Figure 3-2  LE1851w, LE1851wl, LE1851wt, LE2001w, and LE2001wl Rear Components
Table 3-1  LE1851w, LE1851wl, LE1851wt, LE2001w, and LE2001wl
Rear Components
Component Function
1 AC Power Connector Connects the AC power cord to the monitor.
2 DC Connector (LE1851wt
only)Connects the DC to DC cable to the monitor and MultiSeat
Computing device.
3 VGA Connector Connects the VGA cable to the monitor.
Figure 3-3  LE2001wm Rear Components
Table 3-2  LE2001wm Rear Components
Component Function
1...

Connecting the Cables
WARNING!To reduce the risk of electric shock or damage to the equipment:
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
For your safety, do not place anything on power cords or cables. Arrange them so that no one may
accidentally step on or...

LE1851wt Model (Connecting for MultiSeat Computing)
1.Place the monitor in a convenient, well-ventilated location near the computer.
2.Connect the VGA signal cable to the VGA connector on the rear of the monitor and the other end
to the VGA connector on the T150 multiseat computing device.
3.Connect one end of the USB cable (not provided) to the USB connector on the monitor and
connect the other end to a USB connector on the computer.
4.Connect one end of the DC to DC cable to the DC OUT connector on the...

LE2001wm Model
1.Place the monitor in a convenient, well-ventilated location near the computer.
2.Connect a VGA signal cable or DVI-D signal cable.
NOTE:The monitor is capable of supporting either analog or digital input. The video mode is
determined by the video cable used. The monitor will automatically determine which inputs have
valid video signals. The inputs can be selected by pressing the +/Source button on the front panel
or through the On-Screen Display (OSD) feature by pressing the Menu...

Adjusting the Monitor
Tilt the monitors panel forward or backward to set it to a comfortable eye level.
Figure 3-7  Tilting the Monitor
Turning on the Monitor
1.Press the power button on the computer to turn it on.
2.Press the power button on the front of the monitor to turn it on.
CAUTION:Burn-in image damage may occur on monitors that display the same static image on
screen for a prolonged period of time.* To avoid burn-in image damage on the monitor screen, you
should always activate a screen saver...

CAUTION:Before beginning to disassemble the monitor, be sure the monitor is turned off and the
power and signal cables are both disconnected.
1.Disconnect and remove the signal and power cables from the back of the monitor.
2.Lay the monitor face down on a flat surface.
3.Remove the four screws on the back of the monitor that connect the monitor panel to the pedestal
base (1) and slide the pedestal base from the monitor panel (2).
Figure 3-8  Removing the Pedestal Base
10 Chapter 3   Setting Up the...

4.To attach the monitor to a swing arm, insert four 10mm screws through the holes on the swing arm
plate and into the mounting holes on the monitor.
Figure 3-9  Installing the Monitor on a Swing Arm
To attach the monitor to other mounting fixtures, follow the instructions included with the mounting
fixture to ensure that the monitor is safely attached.
CAUTION:This monitor supports the VESA industry standard 100 mm mounting holes. To
attach a third-party mounting solution to the monitor, four 4 mm, 0.7...

Mounting the MultiSeat Computing Device to the
Monitor (Sold Separately)
You can connect a multiseat computing device to the rear of the LE1851wt model only.
1.Install the bracket for the multiseat computing device to the rear of the monitor using the two
10mm screws provided. Install the screws in the upper two VESA mounting holes.
Figure 3-10  Installing the MultiSeat Computing Device Bracket
12 Chapter 3   Setting Up the Monitor ENWW