HP LaserJet P4015dn User Manual

Store jobs
You can store jobs on the product so you can print them at any time. You can share stored jobs with
other users, or you can make them private.
1.On the File menu, click Print.
2.Open the Job Storage menu.
3.In the Job Storage: drop-down list, select the type of stored job.
4.For the Stored Job, Private Job, and Private Stored Job types of stored jobs, enter a name for
the stored job in the box next to Job Name:.
Select which option to use if another stored job already has that name.
●Use Job...

60 Chapter 4   Use the product with Macintosh ENWW
 

5 Connectivity
●USB configuration
●
Network configuration
ENWW61
 

USB configuration
The printer supports a Hi-Speed USB 2.0 port. The USB cable can be a maximum of 5 meters (15 feet)
long.
Connect the USB cable
Plug the USB cable into the printer. Plug the other end of the USB cable into the computer.
1
2
1Type B USB port
2Type B USB connector
62 Chapter 5   ConnectivityENWW
 

Network configuration
You might need to configure certain network parameters on the product. You can configure these
parameters from the control panel, the embedded Web server, or for most networks, from the HP Web
Jetadmin software.
For a complete list of supported networks and for instructions on configuring network parameters from
software, see the HP Jetdirect Embedded Print Server Administrator’s Guide. The guide comes with
products in which an HP Jetdirect embedded print server is installed....

Service nameDescription
BOOTP (Bootstrap Protocol)For automatic IP address assignment. The BOOTP server
provides the product with an IP address. Requires the
administrator to input a products MAC hardware address on
the BOOTP server for the product to obtain an IP address from
that server.
Auto IP For automatic IP address assignment. If neither a DHCP
server nor a BOOTP server is present, the product uses this
service to generate a unique IP address.
Configure the network product
View or change network...

Manually configure IPv4 TCP/IP parameters from the control panel
In addition to using the embedded Web server, you can also use the control-panel menus to set an IPv4
address, subnet mask, and default gateway.
1.
Press Menu 
.
2.Press the down arrow 
 to highlight CONFIGURE DEVICE, and then press OK.
3.Press the down arrow 
 to highlight I/O, and then press OK.
4.Press the down arrow 
 to highlight EMBEDDED JETDIRECT MENU, and then press OK.
5.Press the down arrow 
 to highlight TCP/IP, and then press...

Manually configure IPv6 TCP/IP parameters from the control panel
In addition to using the embedded Web server, you can also use the control-panel menus to set an IPv6
address.
1.
Press Menu 
.
2.Press the down arrow 
 to highlight CONFIGURE DEVICE, and then press OK.
3.Press the down arrow 
 to highlight I/O, and then press OK.
4.Press the down arrow 
 to highlight EMBEDDED JETDIRECT MENU, and then press OK.
5.Press the down arrow 
 to highlight TCP/IP, and then press OK.
6.Press the down arrow 
 to...

Disable network protocols (optional)
By factory default, all supported network protocols are enabled. Disabling unused protocols has the
following benefits:
●Decreases product-generated network traffic
●Prevents unauthorized users from printing to the product
●Provides only pertinent information on the configuration page
●Allows the product control panel to display protocol-specific error and warning messages
Disable IPX/SPX, AppleTalk, or DLC/LLC
NOTE:Do not disable IPX/SPX in Windows-based systems that...

Link speed and duplex settings
The link speed and communication mode of the print server must match the network. For most situations,
leave the product in automatic mode. Incorrect changes to the link speed and duplex settings might
prevent the product from communicating with other network devices. If you need to make changes, use
the product control panel.
NOTE:Making changes to these settings causes the product to turn off and then on. Make changes
only when the product is idle.
1.
Press Menu .
2.Press...