HP LaserJet P3005x User Manual

							
4.Press  to highlight  JAM RECOVERY , and then press .
5. Press 
 or  to select the appropriate  setting, and then press .
6. Press  Menu to exit the menu.
RAM disk
This option determines how the RAM disk  feature is configured. This option is available only if the device
has at least 8 MB of free  memory. The default is AUTO. 
● AUTO
: The device determines the optimal RAM di sk size based on the amount of available
memory.
● OFF
: The RAM disk is disabled, but a minimal RAM disk  is still active (sufficient to scan one page).
Set the RAM disk
1. Press  Menu to open the menus.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
3. Press 
 to highlight  SYSTEM SETUP , and then press .
4. Press 
 to highlight  RAM DISK, and then press .
5. Press 
 or  to select the appropriate  setting, and then press .
6. Press  Menu to exit the menu.
Language
If LANGUAGE  appears in English on the control panel, us e the following procedure. Otherwise, turn
the device off and then on again. When  XXX MB appears, press and hold 
. When all three control
panel lights ar e lit, release 
 and use the following procedure to set the language.
Select the language during initial installation
1. Turn on the device.
2. When  LANGUAGE  appears on the control-panel display in the default language, press 
 to
highlight the preferred language, and then press 
.
Change the language after the initial configuration
After the initial installation, you can change the cont rol-panel display language from the control panel.
1. Press  Menu.
2. Use 
 to highlight  CONFIGURE DEVICE , and then press .
3. Use 
 to highlight  SYSTEM SETUP , and then press .
4. Use 
 to highlight  LANGUAGE , and then press .
5. Use 
 or  to highlight the appropriate language, and then press .
6. Press  Menu to exit the menu.
ENWW Change device-control-panel configuration settings 39
 
						

							
40 Chapter 2   Control panelENWW
 
						

							
3 Input/output (I/O) configuration
This chapter describes how to configure certain network parameters on the printer:
●
Parallel configuration
●
USB configuration
●
Network configuration
ENWW 41
 
						

							
Parallel configuration
NOTEThe information in th is section applies only to mo dels HP LaserJet P3005 and
HP LaserJet P3005d.
A parallel connection is made by connecting the prin ter to the computer using a bidirectional parallel
cable (IEEE-1284 compliant) with a c onnector plugged into the printer parallel port. The cable can be a
maximum of 10 meters (30 feet) long.
When used to describe a parallel interface, the term bi directional indicates that the printer is able to both
receive data from the computer and send data to the computer through the parallel port. While the
parallel interface provides back wards compatibility, a USB or network connec tion is recommended to
optimize performance.
2
1
1Parallel port
2Parallel connector
42 Chapter 3   Input/outpu t (I/O) configuration ENWW
 
						

							
USB configuration
The printer supports a Hi-Speed USB 2.0 port. The USB cable can be a maximum of 5 meters (15 feet)
long.
Connect the USB cable
Plug the USB cable into the printer. Plug the  other end of the USB cable into the computer.
12
1Type B USB port
2Type B USB connector
ENWW USB configuration 43
 
						

							
Network configuration
NOTEThe information in this section applies only to models HP LaserJet P3005n, HP LaserJet
P3005dn, and HP LaserJet P3005x.
You might need to configure certain network parameters on the printer. You can configure these
parameters from the printer control panel, the em bedded Web server, or for most networks, from the
HP Web Jetadmin software.
NOTE For more information about using the embedded Web server, see Use the embedded
Web server .
For a complete list of supported networks and for in structions on configuring network parameters from
software, see the  HP Jetdirect Embedded Print  Server Administrator’s Guide. The guide comes with
printers in which an HP Jetdirect  embedded print server is installed.
Manually configure TCP/IP para meters from the control panel
Use manual configuration to set an IPv4 address, subnet mask, and default gateway.
Set an IPv4 address
1.Press  Menu.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
3. Press 
 to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  TCP/IP, and then press .
6. Press 
 to highlight  IPv4 SETTINGS , and then press .
7. Press 
 to highlight  CONFIG METHOD , and then press .
8. Press 
 to highlight  MANUAL SETTINGS , and then press .
9. Press 
 to highlight  IP ADDRESS , and then press .
10. Press the 
 or  arrow to increase or decrease the number  for the first byte of the IP address.
11. Press 
 to move to the next  set of numbers. (Press  to move to the previous set of numbers.)
NOTETo cycle through the numbers more qui ckly, hold down the arrow button.
12.Repeat steps 10 and 11 until the correct  IP address is complete, and then press  to save the
setting.
13. Press  Menu to return to the  Ready state.
Set the subnet mask
1.Press  Menu.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
44 Chapter 3   Input/outpu t (I/O) configuration ENWW
 
						

							
3.Press  to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  TCP/IP, and then press .
6. Press 
 to highlight  IPv4 SETTINGS , and then press .
7. Press 
 to highlight  CONFIG METHOD , and then press .
8. Press 
 to highlight  MANUAL SETTINGS , and then press .
9. Press 
 to highlight  SUBNET MASK , and then press .
10. Press the 
 or  arrow to increase or decrease the num ber for the first byte of the subnet mask.
11. Press 
 to move to the next set of numbers. (Press  to move to the previous set of numbers.)
12. Repeat steps 10 and 11 until the correct subnet mask is complete, and then press 
 to save the
subnet mask.
13. Press  Menu to return to the  Ready state.
Set the default gateway
1.Press  Menu.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
3. Press 
 to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  TCP/IP, and then press .
6. Press 
 to highlight  IPv4 SETTINGS , and then press .
7. Press 
 to highlight  CONFIG METHOD , and then press .
8. Press 
 to highlight  MANUAL SETTINGS , and then press .
9. Press 
 to highlight  DEFAULT GATEWAY , and then press .
10. Press the 
 or  arrow to increase or decrease the nu mber for the first byte of the default
gateway.
11. Press 
 to move to the next set of numbers. (Press  to move to the previous set of numbers.)
12. Repeat steps 10 and 11 until the correct def ault gateway is complete, and then press 
 to save
the default gateway.
13. Press  Menu to return to the  Ready state.
Disable network protocols (optional)
By factory default, all supported network protocol s are enabled. Disabling unused protocols has the
following benefits:
● Decreases printer-generated network traffic
● Prevents unauthorized users fr
om printing to the printer
ENWW Network configuration 45
 
						

							
●Provides only pertinent information on the configuration page
● Allows the printer control panel to display protocol-specific error and warning messages
Disable IPX/SPX
NOTE
Do not disable this protocol  in Windows-based systems that  print to the printer through
IPX/SPX.
1. Press  Menu.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
3. Press 
 to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  IPX/SPX, and then press .
6. Press 
 to select  ENABLE.
7. Press 
 to highlight  OFF, and then press .
8. Press  Menu to return to the  Ready state.
Disable AppleTalk
1.Press  Menu.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
3. Press 
 to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  APPLETALK , and then press .
6. Press 
 to select  ENABLE.
7. Press 
 to highlight  OFF, and then press .
8. Press  Menu to return to the  Ready state.
Disable DLC/LLC
1.Press  Menu.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
3. Press 
 to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  DLC/LLC, and then press .
6. Press 
 to select  ENABLE.
7. Press 
 to highlight  OFF, and then press .
8. Press  Menu to return to the  Ready state.
46 Chapter 3   Input/outpu t (I/O) configuration ENWW
 
						

							
Enhanced I/O (EIO) configuration
NOTEIf you are adding a print server to the bas e model, additional printer memory might be
required.
The enhanced input/output (EIO) slot holds compatible accessory devices, such as the HP Jetdirect
print server network cards or other devices. Plugging  an EIO network card into the slot increases the
number of network interfaces available to the printer.
HP Jetdirect EIO print servers
HP Jetdirect print servers  (network cards) can be installed in  EIO slots. These cards support multiple
network protocols and operating systems. HP Jetdirect print servers facilitate network management by
allowing you to connect a printer directly to your ne twork at any location. HP Jetdirect print servers also
support the Simple Network Management Protocol (SNMP), which provides network managers with
remote printer management and troubleshooting through the HP Web Jetadmin software.
NOTE Configure the card either through the control  panel, the printer installation software, or
with HP Web Jetadmin so ftware. Refer to the HP Jetdirect print server documentation for more
information.
ENWW Network configuration 47
 
						

							
48 Chapter 3   Input/output (I/O) configuration ENWW