HP LaserJet P3005dn User Manual

4.Press  to highlight  JAM RECOVERY , and then press .
5. Press 
 or  to select the appropriate  setting, and then press .
6. Press  Menu to exit the menu.
RAM disk
This option determines how the RAM disk  feature is configured. This option is available only if the device
has at least 8 MB of free  memory. The default is AUTO. 
● AUTO
: The device determines the optimal RAM di sk size based on the amount of available
memory.
● OFF
: The RAM disk is disabled, but a minimal RAM disk  is still active...

40 Chapter 2   Control panelENWW
 

3 Input/output (I/O) configuration
This chapter describes how to configure certain network parameters on the printer:
●
Parallel configuration
●
USB configuration
●
Network configuration
ENWW 41
 

Parallel configuration
NOTEThe information in th is section applies only to mo dels HP LaserJet P3005 and
HP LaserJet P3005d.
A parallel connection is made by connecting the prin ter to the computer using a bidirectional parallel
cable (IEEE-1284 compliant) with a c onnector plugged into the printer parallel port. The cable can be a
maximum of 10 meters (30 feet) long.
When used to describe a parallel interface, the term bi directional indicates that the printer is able to both
receive data from the...

USB configuration
The printer supports a Hi-Speed USB 2.0 port. The USB cable can be a maximum of 5 meters (15 feet)
long.
Connect the USB cable
Plug the USB cable into the printer. Plug the  other end of the USB cable into the computer.
12
1Type B USB port
2Type B USB connector
ENWW USB configuration 43
 

Network configuration
NOTEThe information in this section applies only to models HP LaserJet P3005n, HP LaserJet
P3005dn, and HP LaserJet P3005x.
You might need to configure certain network parameters on the printer. You can configure these
parameters from the printer control panel, the em bedded Web server, or for most networks, from the
HP Web Jetadmin software.
NOTE For more information about using the embedded Web server, see Use the embedded
Web server .
For a complete list of supported networks...

3.Press  to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  TCP/IP, and then press .
6. Press 
 to highlight  IPv4 SETTINGS , and then press .
7. Press 
 to highlight  CONFIG METHOD , and then press .
8. Press 
 to highlight  MANUAL SETTINGS , and then press .
9. Press 
 to highlight  SUBNET MASK , and then press .
10. Press the 
 or  arrow to increase or decrease the num ber for the first byte of the subnet mask.
11. Press 
 to...

●Provides only pertinent information on the configuration page
● Allows the printer control panel to display protocol-specific error and warning messages
Disable IPX/SPX
NOTE
Do not disable this protocol  in Windows-based systems that  print to the printer through
IPX/SPX.
1. Press  Menu.
2. Press 
 to highlight  CONFIGURE DEVICE , and then press .
3. Press 
 to highlight  I/O, and then press .
4. Press 
 to highlight  EMBEDDED JETDIRECT , and then press .
5. Press 
 to highlight  IPX/SPX, and then...

Enhanced I/O (EIO) configuration
NOTEIf you are adding a print server to the bas e model, additional printer memory might be
required.
The enhanced input/output (EIO) slot holds compatible accessory devices, such as the HP Jetdirect
print server network cards or other devices. Plugging  an EIO network card into the slot increases the
number of network interfaces available to the printer.
HP Jetdirect EIO print servers
HP Jetdirect print servers  (network cards) can be installed in  EIO slots. These...

48 Chapter 3   Input/output (I/O) configuration ENWW