HP LaserJet Enterprise P3015dn User Manual

ItemSub-itemValuesDescription
PERSONALITY AUTO*
PCL
PDF
PSSet the default personality.
CLEARABLE WARNINGS JOB *
ONSets whether a warning is cleared
on the control panel or when
another job is sent.
AUTO CONTINUE OFF
ON *Determines product behavior
when the system generates an
Auto Continuable error.
JAM RECOVERY AUTO *
OFF
ONSet whether the product tries to
reprint pages after a jam.
AUTO : The product reprints pages
if enough memory is available for
full-speed two-sided printing.
RAM DISK AUTO *
OFFSets...

I/O menu
Items on the I/O (input/output) menu affect the communication between the product and the computer.
If the product contains an HP Jetdirect print server, you can configure basic networking parameters by
using this submenu. You can also configure these and other parameters through HP Web Jetadmin or
the embedded Web server.
For more information on these options, see 
Network configuration on page 65.
To display: Press the  Menu button 
, select the  CONFIGURE DEVICE  menu, and then select the...

ItemSub-itemSub-itemValuesDescription
 IPV4 SETTINGSCONFIG METHODBOOTP
DHCP*
AUTO IP
MANUALSpecify the method that TCP/IPv4
parameters are configured on the
HP Jetdirect print server.
BOOTP : Automatic configuration from a
BootP (Bootstrap Protocol) server.
DHCP : Automatic configuration from a
DHCPv4 (Dynamic Host Configuration
Protocol) server. If selected and a DHCP
lease exists, the  DHCP RELEASE  and
DHCP RENEW  menus are available to set
DHCP lease options.
AUTO IP : Automatic link-local IPv4...

ItemSub-itemSub-itemValuesDescription
  DHCP RENEWYES
NO*Specify whether the print server requests to
renew the DHCP lease.
NOTE: This menu appears if the  CONFIG
METHOD  menu is set to the  DHCP option
and a DHCP lease for the print server exists.
  PRIMARY DNS Specify the IP address (n.n.n.n) of a Primary
DNS Server.
  SECONDARY DNS Specify the IP address (n.n.n.n) of a
Secondary Domain Name System (DNS)
Server.
 IPV6 SETTINGSENABLEON *
OFFEnable or disable IPv6 operation on the print
server....

ItemSub-itemSub-itemValuesDescription
 PROXY SERVER  Specifies the proxy server to be used by
embedded applications in the product. A
proxy server is typically used by network
clients for Internet access. It caches Web
pages, and provides a degree of Internet
security, for those clients.
To specify a proxy server, enter its IPv4
address or fully-qualified domain name. The
name can be up to 255 octets.
For some networks, you might need to
contact your Internet Service Provider (ISP)
for the proxy server...

ItemSub-itemSub-itemValuesDescription
 RESET SECURITY YES
NO*Specify whether the current security settings
on the print server will be saved or reset to
factory defaults.
DIAGNOSTICSEMBEDDED TESTS  This menu provides tests to help diagnose
network hardware or TCP/IP network
connection problems.
Embedded tests help to identify whether a
network fault is internal or external to the
product. Use an embedded test to check
hardware and communication paths on the
print server. After you select and enable a...

ItemSub-itemSub-itemValuesDescription
 PING TEST  Check network communications. This test
sends link-level packets to a remote network
host, then waits for an appropriate response.
To run a ping test, set the following items:
  DEST TYPEIPV4
IPV6Specify whether the target product is an IPv4
or IPv6 node.
  DEST IPV4 Type the IPv4 address.
  DEST IPV6 Type the IPv6 address.
  PACKET SIZE Specify the size of each packet, in bytes, to
be sent to the remote host. The minimum is
64 (default) and the maximum...

ItemSub-itemSub-itemValuesDescription
  RTT AVERAGE Shows the average round-trip-time (RTT),
from 0 to 4096 milliseconds, for packet
transmission and response. The default is 0.
  PING IN
PROGRESSYES
NO*Select whether the control panel indicates
when a ping test is in progress.
  REFRESHYES
NO*When viewing the ping test results, this item
updates the ping test data with current
results. A refresh automatically occurs when
the menu times out or you manually return to
the main menu.
LINK SPEED    AUTO*
10T...

ItemSub-itemValuesDescription
RESTORE FACTORY
SETTINGS  Clear the page buffer, remove all
perishable personality data,
reset the printing environment,
and return all default settings to
factory defaults.
SLEEP MODE OFF
ON* Select whether the product can
enter sleep mode. If you turn this
setting off, you cannot change
any settings in the 
SLEEP
DELAY  menu.
ENWW Configure device menu 37
 

Diagnostics menu
Use the DIAGNOSTICS  menu to run tests that can help you identify and solve problems with the product.
To display: Press the  Menu button 
, and then select the  DIAGNOSTICS menu.
NOTE:Values that have an asterisk (*) are the factory-default values. Some menu items have no
default.
ItemSub-itemValuesDescription
PRINT EVENT LOG  Prints a report containing the last
50 entries in the product’s event
log, starting with the most recent.
SHOW EVENT LOG  Displays the last 50 events, starting...