HP LaserJet Enterprise P3015d User Manual

							Manually configure IPv6 TCP/IP parameters from the control panel
Use the control-panel menus to manually set an IPv6 address.
1.Press the  Menu button 
.
2. Open each of the following menus. Press the down arrow 
 to highlight it and then press the  OK
button to select it.
a. CONFIGURE DEVICE
b. I/O
c. EMBEDDED JETDIRECT MENU
d. TCP/IP
e. IPV6 SETTINGS
f. ADDRESS
g. MANUAL SETTINGS
h. ENABLE
i. ON
j. ADDRESS
3. Use the numeric keypad, or press the up arrow 
 or the down arrow  to enter the address. Press
the  OK button.
NOTE: If you are using the arrow buttons to enter the address, you must press the  OK button
after entering each character.
4. Press the up arrow  or the down arrow  to select the stop character . Press the OK  button.
5. Press the  Menu button 
 to return to the  Ready state.
ENWW Network configuration 69
 
						

							Disable network protocols (optional)
By factory default, all supported network protocols are enabled. Disabling unused protocols has the
following benefits:
●Decreases product-generated network traffic
● Prevents unauthorized users from printing to the product
● Provides only pertinent information on the configuration page
● Allows the product control panel to display protocol-specific error and warning messages
Disable IPX/SPX, AppleTalk, or DLC/LLC
NOTE: Do not disable IPX/SPX in Windows-based systems that print through IPX/SPX.
1.Press the  Menu button .
2. Open each of the following menus. Press the down arrow 
 to highlight it and then press the  OK
button to select it.
a. CONFIGURE DEVICE
b. I/O
c. EMBEDDED JETDIRECT MENU
d. IPX/SPX , APPLETALK, or DLC/LLC
e. ENABLE
f. OFF
3. Press the  Menu button 
 to return to the  Ready state.
70 Chapter 5   Connectivity ENWW
 
						

							Link speed and duplex settings
The link speed and communication mode of the print server must match the network. For most situations,
leave the product in automatic mode. Incorrect changes to the link speed and duplex settings might
prevent the product from communicating with other network devices. If you need to make changes, use
the product control panel.
NOTE:Making changes to these settings causes the product to turn off and then on. Make changes
only when the product is idle.
1. Press the  Menu button .
2. Open each of the following menus. Press the down arrow 
 to highlight it and then press the  OK
button to select it.
a. CONFIGURE DEVICE
b. I/O
c. EMBEDDED JETDIRECT MENU
d. LINK SPEED
3. Press the down arrow 
 to highlight one of the following options.
SettingDescription
AUTOThe print server automatically confi gures itself for the highest link speed and
communication mode allowed on the network.
10T HALF10 megabytes per second (Mbps), half-duplex operation
10T FULL10 Mbps, full-duplex operation
100TX HALF100 Mbps, half-duplex operation
100TX FULL100 Mbps, full-duplex operation
100TX AUTOLimits auto-negotiation to a maximum link speed of 100 Mbps
1000TX FULL 1000 Mbps, full-duplex operation
4.Press the  OK button. The product turns off and then on.
ENWW Network configuration 71
 
						

							72 Chapter 5   ConnectivityENWW
 
						

							6 Paper and print media
●Understand paper and print media use
●
Supported paper and print media sizes
●
Custom paper sizes
●
Supported paper and print media types
●
Tray and bin capacity
●
Special paper or print media guidelines
●
Load trays
●
Configure trays
●
Use paper output options
ENWW 73
 
						

							Understand paper and print media use
This product supports a variety of paper and other print media in accordance with the guidelines in this
user guide. Paper or print media that does not meet these guidelines might cause poor print quality,
increased jams, and premature wear on the product.
For best results, use only HP-brand paper and print media designed for laser printers or multiuse. Do
not use paper or print media made for inkjet printers. Hewlett-Packard Company cannot recommend
the use of other brands of media because HP cannot control their quality.
It is possible for paper to meet all of the guidelines in this user guide and still not produce satisfactory
results. This might be the result of improper handling, unacceptable temperature and/or humidity levels,
or other variables over which Hewlett-Packard has no control.
CAUTION:Using paper or print media that does not meet Hewlett-Packards specifications might
cause problems for the product, requiring repair. This repair is not covered by the Hewlett-Packard
warranty or service agreements.
74 Chapter 6   Paper and print media ENWW
 
						

							Supported paper and print media sizes
NOTE:To obtain best results, select the correct paper size and type in the printer driver before printing.
Table 6-1   Supported paper and print media sizes
Size and dimensionsTray 1Tray 2 and the
optional 500-sheet
traysDuplexer
(d, dn, and x models only)
Letter
216 x 279 mm (8.5 x 11 in)
Legal
216 x 356 mm (8.5 x 14 in)
Executive
184 x 267 mm (7.24 x 10.51 in) 
Statement
140 x 216 mm (5.5 x 8.5 in) 
8.5 x 13
216 x 330 mm (8.5 x 13 in)
3 x 5
76 x 127 mm (3 x 5 in)  
4 x 6
102 x 152 mm (4 x 6 in)  
5 x 7
127 x 188 mm (5 x 7 in) 
5 x 8
127 x 203 mm (5 x 8 in) 
A4
210 x 297 mm (8.27 x 11.69 in)
A5
148 x 210 mm (5.83 x 8.27 in) 
A6
105 x 148 mm (4.1 x 5.8 in) 
B5 (JIS)
182 x 257 mm (7.2 x 10.1 in) 
B6 (JIS)
128 x 182 mm (5.0 x 7.2 in) 
ENWW Supported paper and print media sizes 75
 
						

							Size and dimensionsTray 1Tray 2 and the
optional 500-sheet
traysDuplexer
(d, dn, and x models only)
10 x 15 cm
100 x 150 mm (3.9 x 5.9 in)  
16K
184 x 260 mm (7.2 x 10.2 in) 
16K
195 x 270 mm (7.7 x 10.6 in) 
16K
197 x 273 mm (7.8 x 10.8 in) 
Double Postcard (JIS)
148 x 200 mm (5.8 x 7.9 in) 
Custom
76 x 127 mm to 216 x 356 mm (3.0 x 5.0 in to 8.5 x 14 in)  
Custom
105 x 148 mm to 216 x 356 mm (4.13 x 5.83 in to 8.5 x 14
in)  
Custom
210 x 280 mm to 216 x 356 mm (8.27 x 11 in to 8.5 x 14 in)  
Envelope Commercial #10
105 x 241 mm (4.13 x 9.49 in)  
Envelope DL ISO
110 x 220 mm (4.33 x 8.66 in)  
Envelope C5 ISO
162 x 229 mm (6.93 x 9.84 in)  
Envelope B5 ISO
176 x 250 mm (6.7 x 9.8 in)  
Envelope Monarch #7-3/4
98 x 191 mm (3.9 x 7.5 in)  
Table 6-1  Supported paper and print media sizes (continued)
76 Chapter 6   Paper and print mediaENWW
 
						

							Custom paper sizes
This product supports a variety of custom paper sizes that are within the minimum- and maximum-size
guidelines for the product but are not listed in the supported paper sizes table. When using a supported
custom size, specify the custom size in the print driver, and load the paper in a tray that supports custom
sizes.
ENWW Custom paper sizes 77
 
						

							Supported paper and print media types
For a complete list of specific HP-brand paper that this product supports, go to www.hp.com/support/
ljp3010series.
Paper type (control panel)Paper type (printer driver)Tray 1Tray 2 and
optional 500-
sheet traysAutomatic
duplex printing
PLAINPlain
LIGHT 60–74 G/M2Light 60-75g
BONDBond
RECYCLEDRecycled
MIDWEIGHT 96–110 G/M2Midweight
HEAVY 111–130 G/M2Heavy
EXTRA HEAVY 131–175 G/M2Extra Heavy  
CARDSTOCKCardstock  
MONO TRANSPARENCYMonochrome Laser Transparency  
LABELSLabels  
LETTERHEADLetterhead
ENVELOPEEnvelope  
PREPRINTEDPreprinted
PREPUNCHEDPrepunched
COLOREDColored
ROUGH Rough  
78 Chapter 6   Paper and print media ENWW