HP LaserJet 9050 User Manual

							ENWWClearing jams99
Clearing jams from the input tray areas
To clear jams in optional Tray 1
1Check for paper in the optional Tray 1 area, and remove any paper from this area. Carefully 
check to be sure you have removed all pieces of torn paper.
2 Open and close the right door to reset the printer.
To clear jams i nside the right door
1Open the right door.
2 Check for paper in the right door area, and remove any paper from this area. Carefully check 
to be sure you have removed all pieces of torn paper.
 
						

							100Chapter 6 Problem solving ENWW
3
Open the jam access cover. Pull out and lift the green tab.
4 Remove any paper from this area  by pulling it out of the printer.
5 Push the green lever down to original position.
6 Close the right door.
To clear jams in Trays 2 and 3
1Open the tray until it stops.
2 Check for paper in the tray area, and remove any paper from this area. Carefully check to be 
sure you have removed all pieces of torn paper.
 
						

							ENWWClearing jams101
3
Close the tray.
4 Open and close the right door to reset the printer.
To clear jams in optional Tray 4
1Open the vertical transfer door on optional Tray 4.
2 Check for paper in this area, and remove any paper from this area. Carefully check to be 
sure that you have removed all pieces of torn paper.
 
						

							102Chapter 6 Problem solving ENWW
3
If you did not see any paper in the right access door, open optional Tray 4.
4 Check for paper in the tray area, and remove any paper from this area. Carefully check to be 
sure you have removed all pieces of torn paper.
5 Close optional Tray 4.
6 Close the vertical transfer door.
 
						

							ENWWClearing jams103
Clearing jams from the duplex  printing accessory (duplexer)
To clear jams in the duplex printing accessory
1If an optional output device is installed, slide it away from the printer to access the left door.
2 Open the left door and carefully pull out any paper from area.
WA R N I N G ! Avoid touching the adjacent fusing area. It can be  hot.
3 Remove the duplex printing accessory by pressing the green lever and pulling the unit out 
until it stops.
4 Remove any paper by lifting the two green levers in the duplex printing accessory.
 
						

							104Chapter 6 Problem solving ENWW
5
Open the front door.
6 Check for paper in the duplex printing accessory area, and remove any paper by pulling it out 
of the printer. Be careful not to tear the paper.
7 Reinstall the duplex printing acce ssory by sliding it back into the slot until it locks into place.
8 Close all open doors. If an optional output devi ce is installed, push it back into place.
 
						

							ENWWClearing jams105
Clearing jams from the output areas
To clear jams in the standard output bin 
1If the jam extends into the output area, slowly and carefully pull the paper straight out of the 
printer so that it does not tear.
2 Open the left door and carefully pull out any paper from area. (If an optional output device is 
installed, first move it away from the printer to access the left door.)
3 Close all open doors. If an optional output devi ce is installed, push it back into place.
To clear jams in the left door (fuser area)  
1If an optional output device is installed, slide it away from the printer to access the left door.
 
						

							106Chapter 6 Problem solving ENWW
2
Open the left door.
WA R N I N G ! Avoid touching the adjacent fusing area. It can be  hot.
3 Remove any jammed or damag ed paper from this area by pulling it out of the printer.
4 Press down on the green tab and carefully check for paper. Be sure to remove all pieces of 
torn paper.
5 Close the left door. If an optional output device is installed, push it back into place.
 
						

							ENWWClearing jams107
To clear jams in the multifunction finisher
1Open the finisher cover.
2 Slowly and carefully pull the paper straight out of the finisher so that it does not tear.
3 Close the finisher cover.
 
						

							108Chapter 6 Problem solving ENWW
4
Move the finisher away from the printer.
5 Carefully remove any paper from the printer output area.
6 Carefully remove any paper from the finisher input area.
7 Open the stapler-unit door.