HP LaserJet 3052 User Manual

Copy: How do I?
Use this section to answer copying questions.
Copy two-sided documents (HP LaserJet 3050 all-in-one)
To copy a multiple-page stack of two-sided documents (HP LaserJet 3050 all-in-one)
Copies resulting from this procedure are printed on one side, and need to be hand-collated.
1.Load the documents to be copied into the  automatic document feeder (ADF) input tray with the
first page facing down, and with the top of the page leading into the ADF.
2. Press  Start Copy. The odd-numbered pages...

Copy two-sided documents (HP LaserJet 3052/3055 all-in-one)
To copy a multiple-page stack of two-sided documents (3052/3055 all-in-one)
Copies resulting from this procedure are printed on one side, and need to be hand-collated.
1.Load the documents to be copied into the  automatic document feeder (ADF) input tray with the
first page facing up, and with the top of the page leading into the ADF.
2. Press  Start Copy . The odd-numbered pages are copied and printed.
3. Remove the stack from the ADF output...

Use automatic two-sided printing (duplexing) to copy documents
(HP LaserJet 3390/3392 all-in-one)
Use the 2-Sided button on the control panel display to use duplexing to achieve various results.
NOTE The default setting is  1–1. The  2-Sided  LED on the control panel turns on when
another setting is used.
Table 11-1   2-Sided  settings
Document type2-Sided  settingResulting copies2-Sided LED
One-sided1–1One-sidedOff
One-sided1–2Two-sidedOn
Two-sided 2–2Two-sidedOn
To make two-sided copies from one-sided...

To change the default 2-Sided setting
1.On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  Copy setup, and then press 
.
3. Use the  < or the  > button to select  Default 2-sided, and then press 
.
4. Use the  < or the  > button to select the option for how  you normally want to use the automatic
duplexer when you copy documents.
5. Press 
 to save the selection
226 Chapter 11   How do I? ENWW
 

Reduce or enlarge copies
The all-in-one can reduce copies to as little as 25% of the original size or enlarge copies to as much
as 400% of the original size.
Adjusting the copy size
To reduce or enlarge copies for the current job
1.On the all-in-one control panel, press  Reduce/Enlarge.
2. Select the size to which you would like to reduce or enlarge the copies in this job (see the
settings listed under 
Reducing or enlarging copies ).
NOTE If you select  Custom: 25-400%, type a percentage by using the...

Adjust the lighter/darker (contrast) setting
The lighter/darker setting affects the lightness or darkness (contrast) of the copy. Use the following
procedure to change the contrast for the current copy job only.
To adjust the lighter/darker setting for the current job
1.On the all-in-one control panel, press  Lighter/Darker to see the current contrast setting.
2. Use the  < or the  > button to adjust the setting. Move the slider to the left to make the copy
lighter than the original, or move the slider...

Change the copy-collation setting
You can set the all-in-one to automatically collate multiple copies into sets. For example, if you are
making two copies of three pages and the automatic collation is on, the pages print in this order:
1,2,3,1,2,3. If automatic collation is off, the pages print in this order: 1,1,2,2,3,3.
To use the automatic collation, the original document size must  fit into the memory. If it does not, the
all-in-one makes only one copy and a message appears notifying you of the...

Adjust the copy quality
Five copy-quality settings are available: Draft,Text , Mixed , Film photo, and  Picture.
The factory-set default for copy quality is  Text. This setting is the best for items that contain mostly
text.
When making a copy of a photo or graphic, you can select the  Film photo setting for photos or the
Picture  setting for other graphics to increase the  quality of your copy. Select the Mixed setting for
documents that include both text and graphics.
If you want to conserve toner, and...

Copy onto media of different types and sizes
The all-in-one is set to copy on either letter- or A4-size paper, depending on the country/region in
which it was purchased. You can change the size and type of media that you copy to for the current
copy job or for all copy jobs.
Media-size settings
● Letter
● Legal
● A4
Media-type settings
● Plain
● Preprinted
● Letterhead
● Transparency
● Prepunched
● Labels
● Bond
● Recycled
● Color
● Light
● Heavy
● Cardstock
● Envelope
● Vellum
● Rough Paper
To change...

To change the default media-size setting
1.On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  Paper setup, and then press 
.
3. Use the  < or the  > button to select  Def. paper size, and then press 
.
4. Use the  < or the  > button to select a media size and then press 
.
5. Press 
 to save the selection.
To change the default media-type setting
1. On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  Paper setup, and then press 
....