HP DesignJet T610 A1 User Manual

When the printer is powered back on, it takes about three minutes to initialize and check and prepare
the printheads. Preparing the printheads takes about one minute and 15 seconds. However, if the printer
has been off for six weeks or more, preparing the printheads could take up to 45 minutes.
Change the language of the front-panel display
There are two possible ways to change the language of the front-panel menus and messages.
●If you can understand the current front-panel display language, press the...

Access the Embedded Web Server
The Embedded Web Server enables you to manage your printer remotely using an ordinary Web
browser running on any computer.
To access the Embedded Web Server directly, you must have a TCP/IP connection to your printer.
However, you can access the Embedded Web Server indirectly, through HP Easy Printer Care
(Windows) or HP Printer Utility (Mac OS) if you connect to your printer with a USB connection.
The following browsers are known to be compatible with the Embedded Web...

To complete the change, you must close and reopen your Web browser.
Change the sleep mode setting
If the printer is left switched on but unused for a certain period of time, it goes automatically into sleep
mode to save power. To change the time the printer waits before it goes into sleep mode, press the
Menu key to return to the main menu and select the Setup menu icon 
, then Front panel
options > Sleep mode wait time. Highlight the wait time you want and then press the OK key. You can
set the time to...

Change the graphic language setting
NOTE:You should not need to change the default graphic language setting (Automatic), and you are
not recommended to do so.
You can change the graphic language setting from the front panel. Press the Menu key to return to the
main menu the select the Setup menu icon 
, then Printer preferences > Select graphic
language. Select one of the following options and press the OK key to set the value.
●Select Automatic to let the printer determine which type of file it is...

5 Paper handling
●General advice
●
Load a roll onto the 24-inch spindle
●
Load a roll onto the 44-inch spindle
●
Load a roll into the 24-inch printer
●
Load a roll into the 44-inch printer
●
Unload a roll
●
Load a single sheet
●
Unload a single sheet
●
View information about the paper
●
Paper profiles
●
Print on loaded paper
●
Maintain paper
●
Change the drying time
●
Turn the automatic cutter on and off
●
Feed and cut the paper
ENWW25
Paper handling
 

General advice
CAUTION:Before starting a paper loading process, ensure you have enough room around the printer,
both in front and behind.
CAUTION:Make sure the printer wheels are locked (the brake lever is pressed down) to prevent the
printer from moving.
CAUTION:All paper must be 11 inches (28 cm) or longer. A4 and letter paper cannot be loaded
landscape.
TIP:For photo paper wear cotton gloves to avoid transferring oils onto the paper.
CAUTION:Keep the basket closed throughout the loading process.
Load...

1.Remove the spindle from the printer one end at a time.
WARNING!Do not insert your fingers into the spindle supports during the removal process.
2.The spindle has a stop at each end to keep the roll in position. The blue stop can be removed to
mount a new roll; it slides along the spindle to hold rolls of different widths. Remove the blue paper
stop from the end of the spindle.
3.If your roll has a three-inch cardboard core, ensure that the core adaptors supplied with the printer
have been installed....

TIP:You may need two people to handle a large roll.
5.Slide the new roll onto the spindle. Make sure the paper type is oriented as shown. If it is not,
remove the roll, turn it 180 degrees and slide it back on to the spindle. There are labels on the
spindle showing the correct orientation.
NOTE:From the back of the printer, the blue stopper is inserted into the right-side holder.
Ensure both ends of the roll are as close to the spindle stops as possible.
6.Put the blue paper stop on to the open end of...

1.Remove the black end of the spindle from the printer, then the blue end.
CAUTION:Be sure to remove the black end first. Removing the blue end first could damage the
black end.
WARNING!Do not insert your fingers into the spindle supports during the removal process.
2.The spindle has a stop at each end to keep the roll in position. The blue stop can be removed to
mount a new roll; it slides along the spindle to hold rolls of different widths. Remove the blue paper
stop from the end of the spindle.
3.If...

4.If the roll is long; rest the spindle horizontally on a table and load the roll on the table.
TIP:You may need two people to handle a large roll.
5.Slide the new roll onto the spindle. Make sure the paper type is oriented as shown. If it is not,
remove the roll, turn it 180 degrees and slide it back on to the spindle. There are labels on the
spindle showing the correct orientation.
NOTE:From the back of the printer, the blue stopper is inserted into the right-side holder.
Ensure both ends of the roll...