HP Designjet T1300 1118 mm User Manual

Change the language of the front-panel display
There are two possible ways to change the language of the front-panel menus and messages.
●
If you can understand the current front-panel display language, press 
, then , then
Setup > Front panel options > Select language.
●If you cannot understand the current front-panel display language, start with the printer powered
off. Press the Power key to turn it on. When you see icons appear on the front panel, press 
 and
then 
. The front panel acknowledges this...

You can see your printers IP address on the front panel by pressing  and then .
If you have followed these instructions but failed to get through to the Embedded Web Server, see
Cannot access the Embedded Web Server on page 193.
Change the language of the HP Utility
The HP Utility can work in the following languages: English, Portuguese, Spanish, Catalan (Windows
only), French, Italian, German, Russian, Simplified Chinese, Traditional Chinese, Korean and Japanese.
●Under Windows, select Tools > Set...

Change the units of measurement
To change the units of measurement in the front-panel display, press , then , then Setup >
Front panel options > Select units, and select English or Metric. By default the units are set to
metric.
Configure network settings
You can view and configure the network settings from the Embedded Web Server, the HP Utility or the
front panel.
To do so with the Embedded Web Server, select the Setup tab, then Networking.
With the HP Utility under Windows, select the Settings tab,...

To configure the same network settings from the front panel, press , then , then
Connectivity > Network connectivity > Fast/Gigabit Ethernet > Modify configuration.
You have various other options available from the Connectivity > Network connectivity >
Advanced menu.
●I/O timeout: Specify the time that an idle connection is allowed to remain open when the printer
is waiting for a remote computer. The default value is 30 seconds. If set to zero, the timeout is
disabled and the connection is allowed to...

Manage ePrinter security
When you have set up Web Services, the printer is in unlock mode. In unlock mode, anyone who
knows your printers email address can print to your printer by just sending a file to it. Although HP
provides a spam filtering service, you should be careful about giving out your printers email address,
as everything sent to that address may be printed on your printer.
If you are the printer administrator, you can manage ePrinter security or change your printer status to
lock mode by...

5 Paper handling
●General advice
●
Load a roll onto the spindle
●
Load a roll into the printer
●
Unload a roll
●
Load a single sheet
●
Unload a single sheet
●
View information about the paper
●
Paper presets
●
Printing paper info
●
Move the paper
●
Maintain paper
●
Change the drying time
●
Turn the automatic cutter on and off
●
Feed and cut the paper
38 Chapter 5   Paper handling ENWW
 

General advice
CAUTION:Before starting a paper loading process, ensure you have enough room around the
printer, both in front and behind.
CAUTION:Make sure the printer wheels are locked (the brake lever is pressed down) to prevent the
printer from moving.
CAUTION:All paper must be 280 mm (11 in) or longer. A4 and letter paper cannot be loaded in
landscape orientation.
TIP:For photo paper wear cotton gloves to avoid transferring oils onto the paper.
CAUTION:Keep the basket closed throughout the loading...

Load a roll onto the spindle
1.Open the roll cover.
2.Remove the black end of the spindle from the printer, then the blue end.
CAUTION:Be sure to remove the black end first. Removing the blue end first could damage the
black end.
WARNING!Do not insert your fingers into the spindle supports during the removal process.
3.The spindle has a stop at each end to keep the roll in position. The blue stop can be removed to
mount a new roll; it slides along the spindle to hold rolls of different widths. Remove the...

5.Slide the new roll onto the spindle. Make sure the paper type is oriented as shown. If it is not,
remove the roll, turn it 180 degrees and slide it back on to the spindle. There are labels on the
spindle showing the correct orientation.
NOTE:From the back of the printer, the blue stopper is inserted into the right-side holder.
Ensure both ends of the roll are as close to the spindle stops as possible.
6.Put the blue paper stop on to the open end of the spindle, and push it towards the end of the roll....

NOTE:The first three steps below are optional: you can start with step 4. However, in this case the
printer will not keep track of the length of the roll, and will print no barcode on the roll when it is next
unloaded. So you are recommended to follow all the steps, starting with step 1, unless you have turned
off the Printing paper info option. See 
Printing paper info on page 47.
1.
From the front panel, press , then the roll icon, then Load.
Alternatively, press 
, then , then Paper > Paper load >...